Showing results: 811 - 825 of 931 items found.
-
3443 -
KANOMAX USA, Inc.
The Kanomax Digital Dust Monitor – Model 3443 measures aerosol concentrations corresponding to PM10. The intake isolates the aerosol sample so that the optics chamber is kept sterile for improved reliability and low maintenance. The unit measures 0.1 to 10µm particle size aerosol contaminants such as fumes, dust, smoke and mists. It is battery-operated, data-logging, light-scattering laser photometer that gives you real time aerosol mass readings. It is also suitable for clean office settings well as harsh industrial workplaces, construction and environmental sites, and outdoor applications.
-
Luzchem Research Inc.
The new Extra Large Photoreactor(LPD) is designed to meet stringent specifications while maximizing convenience of operation. Features include:*Sequential photochemical and thermal cycles in a single chamber optimized for dual photothermal decontamination.*Programmable exposure time.*Includes rotor/carousel to ensure samples are evenly exposed to UV irradiation.*Front window with UV protection (420 nm cut off) allows operator to inspect. No UV exposure and no need to open compartment.*Magnetic interlock shuts down system for operator safety if front window is removed.
-
FISCHERSCOPE X-RAY/XUL -
Helmut Fischer AG
For coating thickness measurements in the electroplating industryFixed aperture and fixed primary filterX-ray tube with a slightly larger primary spot, well suited for applications with measurement spot sizes starting at about 1 mmLow-energy beam components are excited with lower effectiveness, however for standard applications measuring the thickness of typical electroplated coatings such as Cr, Ni, Cu, this poses little to no problemMeasuring direction from bottom to top, this allows for quick and easy sample positioningLarge measurement chamber with a cutout (C-slot) Standard X-ray tube, proportional counter tube
-
PA-3000-A ETCHER -
TEK-VAC INDUSTRIES Inc.
Process chamber with plasma view window and full access hinged door. RF hot process shelves with opposing ground electrodes. Throttle valve. Capacitance manometer. Internal pumping system with option for Fomblin filled chemical series mechanical pump. Flow control electronics and cabinet. Up to four mass flow control assemblies can be incorporated into our system. RF matching network and 600 watt maximum power supply. Fully enclosed cabinet. Custom internal fixturing to accommodate specific substrate shapes and sizes. Plasma gas selection for optimal performance.
-
Exosens Group
As a neutron has no charge, a neutron detector incorporates a neutron-to-ionisation particle converter.The incident neutrons are captured by the converter material which then produces (detectable) ionising particles by means of a nuclear reaction.Photonis gas-filled detectors are designed to detect thermal neutrons (En < 0.025 eV), so the capture cross-section of the detecting material must be as large as possible for this low energy. We therefore use 235U (580 barn at 20 °C) for our fission chambers, and 10B (3840 barn at 20 °C) for our boron-lined proportional counters.
-
Data Patterns Pvt. Ltd.
Solution to test redundant Architecture of BMUComprehensive test system performing tests of > 3000 I/O's Special test circuits using hybrid / ceramic components to operate in Thermovac chamber Tests various subsystem functionalities like, AOCS, Sensor Electronics, Telemetry, Tele-command with Self test and application test software
-
Quest Engineering Solutions
Sound Power testing is required in many international standards. Quest also offers a variety of additional acoustic tests and the design experience to help you develop quieter products for your customers. Our chamber is able to cancel out all outside forces as well with its free floating floor boards.
-
RAIN Xplorer -
CISC Semiconductor GmbH
The CISC RAIN Xplorer is a unique RFID test product developed for convenient tag frequency sensitivity, communication range, and backscatter measurements. The RFID tester is designed for open area tests and measurements in an RF-controlled environment using portable or fixed RF test chambers. The system is supplied with software and a reference tag for self-calibration.
-
KoCoS Messtechnik AG
ACTAS test systems provide precise information as to the condition of the chamber and drive unit without requiring them to be opened. The sheer number of parameters to be determined, the wide variety of different types of switchgear equipment in use and the harsh environmental conditions encountered during on-site tests place extreme demands on test equipment.
-
HD320B2 -
Delta OHM S.r.L.
The probe measures the carbon dioxide concentration in air. It’s indicated for checking and monitoring the indoor air quality. Typical applications are the check of the air quality in all the buildings where there is a crowd of people (schools, hospitals, auditoria, canteens, etc.), in the working places to optimize the comfort. CO2 measurement is obtained with an infrared special sensor (NDIR technology: Non-Dispersive Infrared Technology) that, thanks to the use of a double filter and a special measurement technique, warranties precise, stable and long-term measurements. The air to check is spread inside the measurement chamber through the protection membrane placed at the top of the probe.
-
Sataton Instruments Technology CO., Ltd
Face Masks bacterial filtration efficiency BFE tester is to determine the bacterial filtration efficiency (BFE) of medical face mask materials by employing a ratio of the upstream bacterial challenge to downstream residual concentration of the tested medical face mask materials. The tester provides certain flow rate of bacterial aerosol. The operator can measure the number of colony forming units passing through the medical face mask material, which is clamped between a six-stage Anderson cascade impactor and an aerosol chamber, expressed as a percentage of the number of colony forming units present in the challenge aerosol.
-
220/220+ -
Atlas Material Testing Technology
The Xenotest 220 and Xenotest 220+ are large capacity lightfastness testers dedicated for textile testing. They come with premium on-rack light and temperature sensor and non-aging optical filter technology. With the ability to test 38 samples, the 220 Series provides nearly twice as much capacity in the same footprint compared to 150S+. The combination of its large test chamber and the efficient use of power and water make it today‘s most economic air-cooled instrument available. It complies to standards ISO 105 B02, AATCC TM16 (option 3), and Marks & Spencer C9, C9A.
-
TW / CW series -
Clima Temperatur Systeme
Walk or drive-in temperature and climatic test chambers can be designed from CTS by a standardized grid system affordable in all sizes. The refrigeration performance data are adjusted here by our experienced sales and project engineers on your testing out. The walk / drive-chambers are ideal for larger components and finished products. CTS as a medium sized company attaches great importance to the detail quality of the equipment components, with only the best supplier products such as compressor and solenoid valves are used. Your resulting advantages are trouble-free long-term operation and thus no loss of valuable test time.
-
TPD Workstation -
Hiden Analytical Ltd.
The Hiden TPD Workstation is a complete experimental system for UHV temperature programmed desorption (TPD) studies. The triple filter mass analyser is configured with a cooled shroud giving the analyser optimum sensitivity with minimum background contributions to desorption products from the sample. A fast sample load lock with sample transfer mechanism is included to provide for rapid sample change. The TPD Workstation features a multiport UHV chamber with heated sample stage coupled to a high precision triple filter analyser with digital pulse ion counting detector for ultimate sensitivity and time resolution.
-
Qualitest International Inc.
Qualitest offers Charpy / Izod Impact Testers with capacities up to 750J meeting and exceeding ASTM E23, ISO, DIN, JIS, standard requirements. The key benefits of this line of top technology models are price competitiveness, extremely high precision and durability, automatic motorized lifting of the pendulum hammer to optimize cycle times, flexibility, efficiency for low/high temperature testing, and much more. Optionally we offer temperature chambers, automated sample handling, centering device, Charpy sample preparation and broaching machines for preparation of notched bar specimens.
