Showing results: 166 - 180 of 211 items found.
-
SE-1004A -
KILTER ELECTRONIC CO.,LTD
●Measure the capacity ●Measure the impedance of the battery●Used as a battery charger●For Li-ion battery (mobile phone battery) and Ni-MH battery ●Capacity range:0~4.000Ah Accuracy: ±2% of reading Resolution: 1mAh●Voltage range: 0 ~ 5V Accuracy: ±0.5% of reading Resolution: 0.001V●Impedance range: 0~1000mΩ Accuracy: ±5% of reading Resolution: 1mΩ●Maximum charge end voltage: 4.400V●Minimum discharge end voltage: 0.000V
-
FC5000 Series -
ACECO Electronics Corp.
The Aceco FC5001 is a two-way FM radio tester that has the ability to lock automatically and almost instantly on to any FM signal within its frequency range. FM signals are demodulated and output it through its internal speaker or external earphone. The high sensitivity to nearfild signals makes it ideal for RF security, counter-surveillance and radio communication testing applications. Supplied as a complete with internal NiCd pack, AC wall charger, VHF/UHF flexible antenna and audio earphone.
-
PFK-105 -
Prostat Corporation
- Ionization Test Kit for Measuring Offset Voltage and Discharge Times- Includes a Field Meter, Charge Plate Monitor, ±1000 Volt Charger and Decay Timer- Balance Ionizers per ANSI/ESD SP3.3 Periodic Verification- Measure Ionizer Decay time as per ANSI/ESD S3.1 and ANSI/ESD SP3.3.- Measure Body Voltage Generation and Decay- Evaluate Ionizers and Packaging Materials- Includes a fixture to hold the PFM-711B, CPM-720B and PDT-740B as one- Molded Carrying Case with Foam Insert Included
-
IT8500+ Series -
I-TECH Electronic Co., Ltd
IT8500+series (150W~3000W) single-channel programmable DC electronic loads are designed for middle & high-end applications.They can be offered as multiple solutions according to customer's design and testing requirements.The user can perform online voltage measurements and adjustments or simulate short circuit test using the simple keypad on the front panel. IT8500+ series DC loads are a versatile instrument for static and dynamic testing of power supplies,batteries,DC - DC converters,battery chargers,provides user the best testing solution.
-
ST5S -
Advance Devices Corp.
*Built-in high-precision LCR probe*Convenient one-hand operation*Ideal for Surface Mount Devices*Automated component identification*Automated test range selection*Manual C, R, L, Z and ESR modes*Test signal levels 0.5 and 1.0Vrms*Swiss-made precise test leads*Diode Polarity/Short Testing*Secondary D, Q, ESR parameters*Portable and ergonomic design*Built-in Li-Ion battery*Universal Micro USB charger*High visibility OLED display
-
ATmega32U4 Board -
SparkFun Electronics
This is the LilyPad Arduino USB board, controlled by an ATmega32U4 with the Arduino bootloader. It has a built in power supply socket and an on/off switch with the only extra piece of hardware you need to program the LilyPad USB is a micro-USB cable, since the new IC has built-in USB support. Any of our LiPo batteries can be plugged right into the JST socket to provide you with easy, on-the-go power. That LiPo battery is even rechargeable through the board, no more special external LiPo chargers required!
-
Extech USB200 -
Extech Instruments Corporation
The Extech’s USB200 monitors voltage, current, and charge capacity (mAh) to determine the quality and stability of chargers, power banks, and cables. It’s designed with a standard USB-A connector to plug into a device to be measured. It also has a USB input to test the quality of charging cables by observing the displayed current. The USB Power Monitor measures the output voltage, current, capacity and stability to prolong the charging equipment’s life cycle and memory stores up to 10 readings. Includes protective USB plug cover for storage.
-
PGA-710 -
Prostat Corporation
The PGA-710 Walking Test System is a complete kit designed to perform the walking test per ANSI/ESD STM97.2 and IEC 61340-4-5. The system consist of several devices designed for portability and to perform several different tests which includes measuring the voltage on a person in combination with floor materials and footwear.The kit includes the PGA-710B Data Logger, the PFM-711B Field Meter, CPM-720B Charge Plate Monitor, the PCS-730B Electrostatic Charger, Hand Held Electrode and the Prostat Autoanalysis Software version 2.0.
-
M97 series -
Maynuo Electronic Co.,Ltd
The new M97XX series programmable DC electronic load is a new generation product designed from Maynuo Electronic Co.,Ltd. Incorporating high-performance chips, the M97XX series delivers high speed and high accuracy with a resolution of 0.1 mV and 0.01 mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs). M97XX series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar celland fuel cell etc.test and measurement applications. From 150W to 200KW, there are many models to choose from :
-
M98 Series -
Maynuo Electronic Co.,Ltd
M98 series DC electronic load, as a new generation product of Maynuo Electronic Co., Ltd, is designed for the LED driver application. A special circuit is desiged for the LED driver on the base of the M97XX sereies. Incorporating high-performance chips, the M98XX series delivers high speed and high accuracy with a resolution of 0.1 mV and 0.01 mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs). M98XX series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar celland fuel cell etc.test and measurement applications.
-
BM 25 & MX 40 -
Teledyne Gas & Flame Detection
The BM25 packs the benefits of a fixed system area monitor into a rugged, user-friendly and transportable instrument. It was designed to detect one to five gases for mobile or temporary work applications, team protection, area surveillance or places where fixed detection systems are not suitable.Powered by a NiMH battery pack, the BM 25 multi gas monitor offers up to 170 hours of continuous run time. Other standard features include STEL and TWA values, as well as a data logging capacity of more than four months. Multiple units can be grouped using optional alarm transfer kits. This protects larger areas by transferring alarms from one BM 25 to the next. An intrinsically safe trickle charger is also available for long-term area monitoring in classified zones.
-
MI 3121 -
Metrel d.d.
The MI 3121 SMARTEC Insulation / Continuity is a tester for dead testing of electrical installations. With both an analogue and digital representation of the results, the instrument ensures accurate measurements up to 2000 Ω on continuity and up to 30 GΩ on insulation function. Configurable limits enable a PASS / FAIL evaluation of test results, which is accompanied with the bright red and green indicator lights for comfortable use even in the dark conditions. The MI 3121 is equipped with a built-in charger and has a magnetic holder in order to free up hands for testing.
-
N3600 Series -
Next Generation Instrumental (Shanghai) T&C Tech. Co., Ltd.
N3600 series is developed based on NGI's years of experience in testing for battery fluctuation simulation test, battery charger, high voltage diode, electrolytic capacitor, electromechanical control, ATE test system, etc. It is a high-voltage wide-range programmable DC power supply. According to different test environments in the fields of lab test, system integration test, and mass production line, NGI has made a number of optimization designs based on the international advanced technology. N3600 series is a market leader in similar products in terms of reliability, maintainability and safety.
-
62000D -
Chroma Systems Solutions, Inc.
Chroma 62000D programmable bidirectional DC power supplies have both power source and load characteristics, two quadrant operation, and allows feedback of the power from the DUT. They can be used for testing renewable energy power systems including PV/storage hybrid inverters, power conversion system (PCS) on charging/discharging, and as a battery simulator. The 62000D also is a fit for testing power components used in electric vehicles, such as bidirectional on-board chargers (BOBC), bidirectional DC convertors, and DC-AC motor drivers, and power conversion simulation tests of batteries in both directions.
-
Shenzhen Setec Power Co., Ltd.
SETEC Power EV charging infrastructure can be deployed anywhere EV charging is needed, which makes the foundation for a future of smarter, reliable, and emission-free mobility to become true. All-in-one EV charging solution includes EV fast charger, assorted charging plug, access server protocol and service from reliable electric car charging station with robust connectivity, compact, high-quality AC wall boxes, to innovative electric bus charging systems. SETEC Power has over a decade of experience in creating, installing, and maintaining charging infrastructure.
