Showing results: 1276 - 1290 of 2618 items found.
-
HDYZ -
HD Power Test Equipment Co.ltd
HDYZ Transformer on-load tap changer Tester is a unique moving part that is connected with the circuit of the transformer, It is essential to test the on-load tap changer of action sequence and switching time.HDYZ Transformer On-load Tap Changer Tester is mainly applied to measure the transient waveform, transient time, transient resistance value, three-phase synchronization of transformer on-load tap-changers.
-
PT-14 -
Kharkovenergopribor Ltd.
The locator PT-14 is used as an induction signal receiver in a cable tracing and fault location set for the following applications:• tracing – finding the route and determining the burial depth of underground cables and other hidden utilities;• fault location – pinpointing interphase and phase-to-sheath short circuits faults;• cable identification – identifying a correct cable from a bunch.
-
V‑Series -
Keysight Technologies
The highest real-time oscilloscope measurement accuracy. Keysight uses a proprietary indium phosphide (InP) integrated circuit process to design the key technology blocks to deliver high-bandwidth performance, ultra-low noise, low jitter, and high-voltage signal input. The InP process lets you see your true signal and make the most accurate measurements.
-
T-4 Series -
Picoprobe
T-4 tips are for use in most standard commercial micropositioners for probing integrated circuits, pads, or lines. Each T-4 tip uses the same 10, 22, 35, 60, or 125 micron diameter tungsten wire as our Model 12C Picoprobe, but is mounted to a 0.020 inch diameter, 2 inch long tinned copper shaft.
-
Gold Box "Infinity" -
Acopian Technical Company
*Highly Configurable, with a seemingly Infinite number of Options*Any slot voltage from 1.5v to 150v is available*Remote Sensing*Open Sense protection*Isolated output*Short circuit and overload protection with enhanced surge capabilities*No minimum load required*Internal EMI Filtering*Pluggable connectors*Can be mounted on two surfaces in any orientation
-
North Atlantic Industries
The NAI VPX family of power products include a variety of standard features, including continuous Background Built-In-Test (BIT); remote error sensing; and protection against transients, overvoltage, overcurrent, short circuits and over temperature. These intelligent designs also have the flexibility to address special needs. Optional current share is available on main outputs.
-
Eltel Industries
*Automatic Microprocessor controlled Guarded Bridge Circuit.*Suitable for testing at voltages up to 500kV.*Can be used to measure both Grounded and Un-Grounded Specimens.*Automatic guard circuit for three-terminal measurement.*Interface measurement and automatic interference suppression circuitry.*Optional range Extension Transformer for large capacitance values.*Test data storage facility.*RS-232 computer interface and USB printer interface.*Window Interface Software for data transfer.
-
SY8125 -
Hong Kong Songyang Industrial Ltd.
The devices are fully made by aluminum alloy materials and the table board is composed of fireproofing and heat-proof materials. ● The output voltage and current use soft startup and stop. It has the protection functions of voltage short circuit, current open circuit and power amplification exception.● The device has the features of high stability, good reliability and large output power. ● High level of autoimmunization. The coexistence of special small keyboard and PCs, convenience to use.
-
3536B -
Peaceful Thriving Enterprise Co Ltd
This is a tester to test the function of the 7 way connector of the vehicle. User simply plug the tester with the 7 way or 4 way connector, and switch on the corresponding function of the vehicle to check if the LED indication has lighted up correctly. Use in the garages, workshops where there is a need to check the configuration of circuit. Widely used to test trailer light circuits on most trucks, boats, trailer campers, caravans, food trucks and other trailers.
-
Circuit Check, Inc.
Circuit Check test fixture adapters are utilized when the target ICT tester is not available or has been replaced with a newer technology tester. The tester adapter will often allow existing test fixtures from one test manufacturer to be utilized on another manufacturer test platform, eliminating the need for replacement fixtures. Contact Circuit Check to discuss your tester and fixture combinations for the best choice of a cost effective solution.
-
UTP 9011 RF -
NOFFZ Computer Technik GmbH
Circuit boards are the heart of all electronic devices. To ensure the reliable function of these boards, detailed tests are essential.Our board-level tester UTP 9011 RF works safely, quickly and cost-optimized at circuit board level. Our interchangeable adapters are particularly efficient in this system, with which you can even test different test items at the same time. The shielded NOFFZ HF test chamber always ensures consistently good results.
-
380320 -
Extech Instruments Corporation
The 380320 is an Analog Insulation Tester with a large, easy to read analog display. Featuring a live circuit warning which displays the actual AC voltage measurement, Automatic discharge circuit, Lock Power On feature for extended test times, and Insulation resistance up to 400MΩ. Complete with heavy duty test leads, alligator clip test lead, 6 x AA batteries, hanging strap and hard carrying case.
-
IBEKO Power AB
Coil analyzers and power supply units are portable and lightweight devices intended for use in harsh switchyard and industrial environments. The typical application is switchgear and circuit breaker testing when substation battery is not connected or available. An advantage over substation battery is enabled testing in under-voltage and over-voltage conditions. Furthermore, the stable voltage outputs with a very low ripple (<0,5%) enable an analysis of the coil and motor current graphs recorded with circuit breaker analyzers from different vendors.SAT40AD, POB30AD, and POB40AD are unique devices in the market due to their dual purpose:Power supply for coils and spring-charging motorsTesting circuit breaker’s coils, motor, and auxiliary circuitAll DV Power coil analyzers and power supply units have four separate outputs for opening and closing coils.SAT40AD has two powerful motor outputs (AC and DC) which can withstand up to 40 A inrush current.POB30AD and POB40AD have DC motor output rated up to 30 A and 40 A respectively. With the use of motor outputs, POB and SAT can also be used as a power source or a temporary battery charger.SAT40A II series instruments can be controlled via PC. The DV-Win application software is used to control both SAT and CAT (Circuit Breaker Analyzers & Timers) devices at the same time, making a unique test system for switchgear and circuit breaker testing.
-
Prima Series -
Scope T&M Pvt, Ltd.
Prima Series is designed for Primary Current Injection Testing of Current Transformers, Protection Relays & Circuit Breakers during their Factory Test, Commissioning and Routine Testing.
-
TestStation LX -
Teradyne, Inc.
TestStation LX is a cost-effective in-circuit test solution providing high-volume electronics manufacturers with reliable, high-quality test for the latest printed circuit board assembly technologies.