Showing results: 181 - 195 of 427 items found.
-
SY024PR**Dual -
Synectic Electronics
The SY024PR**2 accepts a frequency input and produces 2 outputs. These can be 2 x 4-20mA or 2 x 0-10V or one of each. The input can be configured by jumpers to match a wide range of transducer signals, e.g. TTL pulse, open collector transistor, reed switch and coil. The reed switch inputs incorporates filtering to prevent false signals from contact bounce. The coil input accepts ac signals as low as 20mV pk-pk. The input board is a master and the second output board is a slave. Three versions are available dependent on user requirements that is;
-
190 -
Electronic Specialties Inc.
Relay Buddy is a quick go / no-go tester for the most common automotive relays. It provides you with an indication of the general health and functioning of the relay switch contacts and coil. Relay Buddy will check the control side of the relay by applying a signal to the relay coil while it checks for proper functioning of the relay contacts. Relay Buddy operates the relay several times during each test session as it watches for consistency in every cycle. Relay Buddy will fail the relay and light the RED LED if any one of the cycles proves unsuccessful during the test session.
-
WTX Series Type II -
ECG KOKUSAI Co., Ltd.
Even 6 lead coil which is not conventionally made by changing the test cable into 6 from 4 is possible. The examination item of DC resistance, impulse, AC hi-pot and insulation resistance can be switched automatically at once.
-
PeakTech Prüf- und Messtechnik GmbH
An extremely robust milliohm measuring device in a splash-proof hard case for professional field service use, e.g. for resistance measurement on motor coils, generators and transformers or for continuity testing on ring bus systems in industrial plants.
-
TOMSAD
*For renewing the original keys (BMW F series and E series, Audi smart key, Porsche ..)*transponder – reading and precoding*copied transponders with SNIFFER function*pilots – test and cloning*test coil immo with ignition
-
Kyoritsu Electrical Instruments Works, Ltd.
Can measure AC current up to 1000A Flexible and light weight by the air core coil used at the sensor part Designed to meet the international safety standard IEC 61010-1 CAT IV 300V, CAT III 600V
-
Series 116 -
Pickering Electronics
SIL relays - Smallest board area. 1A version requires 0.15 x 0.27 inches .(3.8mm x 6.8mm). 1 or 2 switches with 10 Watts rating. 5 or 12 Volt coils with optional diode
-
Series 200 -
Pickering Electronics
Surface Mount Reed Relays. Wide range featuring dry or mercury wetted switches. Coaxial version for high speed digital or RF up to 6 GHz. 5, 12 or 24 volt coils with optional diode
-
Part No. 172 -
Teledyne Defense Electronics Relays & Coax Switch
Centigrid hermetically sealed package, through-hole or surface mountable (SMT-J), non-latching DPDTAvailable options include:172D - coil transient suppression diodeResistive: 1 Amp/28Vdc Inductive: 200 mA/28Vdc (320 mH) Lamp: 100 mA/28Vdc
-
AWX-05S -
ECG KOKUSAI Co., Ltd.
This equipment is a system which does several electric characteristic tests, such as Armature and Stator coils. It is a system which performs an automatic test and judge according to the set-up parameters, and anyone can perform quality test judgment easily by desorbing a work. Moreover, an impulse test is efficient and does the electric examination of the winding state by not destroying the item.It is inductance and Q which the damped oscillatory wave form generated in a transient phenomenon waveform, i.e., coil, and when there are number of turns difference in a coil, a core, the difference in the material, etc. can judge it simultaneously.That is, almost all characters required as a quality of winding can be inspected very much in a short time.
-
Fauser Elektrotechnik
Standard-compliant measurement according to EN 62233For use with the measurement system UMS4Suitable for all signal forms due to measuring with reference procedureIsotropic sensor with 3 x 100 cm coil surfaceFrequency range 10 Hz to 400 kHz
-
Dor Yang precision instrument (Shanghai) Co.,Ltd
1.Fully Automatic and All Metal Detectors - Your detector detects all kinds of metal objects. Unless you have set for some objects that you don’t want to detect.2.LCD – The LCD with light, it improve to identify the metal in night or caliginous outside. 3.Target Identity - The detected objects are shown on the LCD display. You can decide immediately if the objects worth to be recovered.4.Unwanted Target Elimination - You can set the detector not to respond to some objects.5.Unique Tone for Target - You don’t have to keep watching the LCD display, when an object is being detected, an unique tone corresponding to a target will generate. You may even searching when there is little or no light.6.No Clumsy Slack Cable - hidden search coil cable (connecting between control unit and search coil) avoid entangling and for ease of stem length adjustment.7.Headphone Jack - provided for headphone connection. Both stereo or mono headphone can be used.8.Volume Control - for adjusting the output volume to the loud speaker or headphone.9.Batteries Condition Indicator - shows the conditions of the batteries in the battery compartment.10.Waterproof Search Coil - lets you use the detector in the shallow water.11.Adjustable Stem - lets you adjust the detector’s length for comfortable use. The micro-plug that connects the search coil and the controller unit is made of metal which makes the plug more reliable.
-
SwitchPilot -
Electronic Solutions ULM GmbH & Co. KG
The ESU SwitchPilot Decoder is especially optimised for the stationary use on your layout. Regardless of what you prefer, the usual twin coil magnetic switches, switching electrical light signals or an ultra-modern servo control: One of the SwichtPilot decoders will "fit".
-
PA-23, PA-23BH, S-230 -
Geotech Instruments, llc
The Geotech Model S-230 is a high resolution, 1-component, force balanced accelerometer capable of meeting the noise and stability requirements of the most demanding seismic studies. It features a very wide frequency response (DC to 90 Hz) and an internal calibration coil.
-
Part No. S422 -
Teledyne Defense Electronics Relays & Coax Switch
TO-5 hermetically sealed package, SMT-J mounted, magnetic-latching DPDTAvailable options include:S422D - coil transient suppression diodeS422DD - polarity protection diodeResistive: 1 Amp/28Vdc Inductive: 200 mA/28Vdc (320 mH) Lamp: 100 mA/28Vdc