Showing results: 331 - 345 of 427 items found.
-
CS1-RS -
Chuan Sheng Electronics Co., Ltd.
CS1-RS economic type Resistance Indicator has been designed with high accuracy measurement, display and communication of Ohm(2 wire) as like as Coil of motor or transformer.The meter supports Field Calibration function. It can be calibrated with sensor (Resistance) to meet machinery structure.They are also available 1 option of 1 Relay outputs, 1 Analogue output or 1 RS485 (Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission or communication for a wide range of machinery and testing equipments applications.
-
Rinch Industrial Co.,Limited
This instrument is compatible with four standards of site to measure surface roughness of various machinery-processed parts, calculate corresponding and clearly display all measurement parameters.When measuring the roughness of a surface, the sensor is placed on the surface and then uniformly slides along the surface by driving the mechanism by the sharp built-in probe. This roughness causes displacement of the probe which results in change of inductive amount of induction coils so as to generate analogue signal, which is in proportion to the surface roughness at output end of phase-sensitive rectifier.
-
SpecMetrix -
Sensory Analytics
SpecMetrix systems by Sensory Analytics were designed from the ground up to precisely measure the absolute thickness of just about any coating on any substrate. All our systems are flexible for use in virtually any manufacturing environment. They provide coating thickness data of unprecedented accuracy—helping manufacturers reduce costs by optimizing coating process control and product quality. Our systems are easily configured to measure webs, coils, flat sheets, small samples or finished parts.
-
RS-200K -
Taylor Dynamometer, Inc.
RS-200K towing dynamometer is designedfor testing Class A trucks and is the most full-featured, reliable andaccurate towing dynamometer in the industry. The RS-200K is builtwith a heavy-duty steel frame, heavy-duty industrial axles and rides onan air ride suspension. The RS-200K is designed to maintain 200,000Newtons of constant drawbar pull and the ability to simulate an uphillslope of 25%. The towing dyno uses absorbers with special hightemperature coils powered by an industrial generator so there are nolead-acid batteries to charge and testing is unlimited at low speeds.
-
RS-125K -
Taylor Dynamometer, Inc.
RS-125K towing dynamometer is designedfor testing Class A trucks and is the most full-featured, reliable andaccurate towing dynamometer in the industry. The RS-125K is builtwith a heavy-duty steel frame, heavy-duty industrial axles and rides onan air ride suspension. The RS-125K is designed to maintain 125,000Newtons of constant drawbar pull and the ability to simulate an uphillslope of 25%. The towing dyno uses absorbers with special hightemperature coils powered by an industrial generator so there are nolead-acid batteries to charge and testing is unlimited at low speeds
-
RS-110K -
Taylor Dynamometer, Inc.
RS-110K towing dynamometer is designedfor testing Class A trucks and is the most full-featured, reliable andaccurate towing dynamometer in the industry. The RS-110K is builtwith a heavy-duty steel frame, heavy-duty industrial axles and rides onan air ride suspension. The RS-110K is designed to maintain 110,000Newtons of constant drawbar pull and the ability to simulate an uphillslope of 25%. The towing dyno uses absorbers with special hightemperature coils powered by an industrial generator so there are nolead-acid batteries to charge and testing is unlimited at low speeds.
-
Adamant Namiki Precision Jewel Co Ltd.
There is a structure in the cage shape by only the copper wire turns around a cylindrical permanent magnet placed inside It is a feature. There There is not an anron core, it does not receive the action of the copper basket type rotor is light, the moment of inertia becomes small, so quick response is possible. A Permanent Magnet, There Is No Cogging, That Is, Rotation Is Smooth, And Vibration And Noise Can Be Reduced. - Since Rare Earth Magnets With High Magnetic Properties Are Used And The Rotor Is Formed Only With Coils, The Motor Itself Can Be Made smaller and lighter.
-
ST-670 -
Standard Electric Works Co., Ltd
● DC up to 50A● AC up to 30A● Hz Meter : Measuring Ranges : 45~55 Hz, 45~65 Hz, 55~65 Hz Rated Voltage : 110V, 220V Accuracy : Class 2.0● Case and Composition: Acrylic resin front and Bakelite case. Four studs mounting.● Accuracy : Moving coil type：Class 2.0 Moving lron type：Class 2.5 Rectifier : Class 2.0● Color：Black case. white scale plate..● Pointer：Tube or knife-type, color in black or red.
-
HVST -
Test Electronics
The most important features of the surge tester are its ability to test the entire winding insulation system. A high voltage surge generates turn to turn, coil to coil, and phase to phase voltage stress, as well as ground insulation stress. When used as a dielectric test, accurate voltage readings are essential. The HV Surge Tester monitors the voltage directly across the winding under test. This voltage is displayed on an oscilloscope and recorded on the Pass/ Fail LED latch monitor. This voltage will be accurate despite the impedance of the winding being tested. The insulation system can be tested way above the operating voltage because of the brief duration of the applied voltage test pulse. This allows faults to be detected long before they become apparent at operating conditions.
-
CRMS -
Ultra-Tech Enterprises, Inc.,
The CRMS is a system designed to allow any user to measure the resistance of each set of relay contacts associated with the relay under test. The test system consists of a CONTACT RESISTANCE MEASUREMENT UNIT (CRMU), a MULTIPLE RELAY TEST RACK, as well as an interconnect CABLE ASSEMBLY. Either DC or AC energy to pick and drop relay coils under test for all contact measurements is supplied from the CRMU and easily interfaces with the Multiple Relay Test Rack. For additional and more thorough testing of relays an external relay tester can be interfaced to the Multiple Relay Test Rack to supply energy to the relay coil. It is recommended that the UTE Relay Tester With Timer/Counter (UTE Product # 15967-00) be utilized so the operator can take full advantage of the unique features it offers
-
Pulse Electronics
Molded inductors are constructed by pressing or molding a magnetic material around a pre-wound coil and lead-frame to form the inductor. Our molded inductors provide a fully shielded, high energy density, soft saturation solution for applications up to 110Apk. The construction enables low profile solutions in a cost effective and robust solution that minimizes acoustic noise. We offer a high saturation current series (commercial and automotive, -40C to 125C) and a low DCR series (automotive, -55C to 155C) in a wide range of platforms from 4x4x1.2mm up to 24x24x13mm.
-
RCTi and RCTi 3ph -
Powertek LLC
The RCTi & RCTrms sensors convert ac current to an isolated 0-5V voltage or 4-20mA current loop. TA5V-5A allows compatibility with existing 1A or 5A CT metering circuits. Both offer a choice of proportional (rms) and instantaneous outputs. The available RCT current ranges are 0-100A to 0-50,000Apk. Both RCTi and RCTrms provide accurate measurement over a wide bandwidth ensuring precise measurement even with harmonically distorted wave shapes - using a flexible clip-on sensing coil. The RCTs are available as single and three phase models.
-
DAC-6021 -
Soken Electric Co. Ltd
DAC-6021 is a measurement system for testing Partial Discharge of high frequency equipment, power devices, stator coils, etc.Since the system combines Partial Discharge Measuring Instrument (DAC-PD-3) with Testing Corona-free Variable Frequency Voltage Source (DAC-WT-50) and Testing Shielded Chamber, most external noises are removed, and the measurement is safe.
-
TDR900 -
Doble Engineering
The TDR900 is your entry-level portable circuit breaker test set.It operates and records a circuit breaker's contact timing, motion, velocity, main contact engagement & synchronization, trip and close coil initiation and currents.Use the TDR900 to verify control circuit, check motion of moving parts, validate time of operation and demonstrate results of circuit breaker maintenance.
-
BW-MST-E5000 -
B&W Engineering Corp.
The Mechanical Shock Tower develops the kinetic energy electromagnetically. An iron core "bullet" is attracted to the magnetic core of the solenoid by the dense magnetic field that is created as current flows through the field coil of the shock tower. As the bullet is drawn into the center of the magnetic field the acceleration increases exponentially as the gap reduces to zero on impact causing the high impact shock
