Showing results: 46 - 60 of 191 items found.
-
Test Head Engineering, LLC
Nest and Pod Fixtures are used to test components and sub-assemblies. They typically are built in an array and the devices under test are subjected to tests that simulate operating conditions or life-cycle testing. Test Head Engineering is experienced in providing nest and pod testers that meet the connectivity, ergonomic and mechanical requirements of component testing.
-
CB50 -
CAMI Research Inc. (CableEye®)
Populated with precision resistors, it allows users to determine empirically whether the tester requires calibration. The CB50 may be used on all CableEye models. The CB50 is intended for periodic verification of tester calibration. To ensure that resistance measurements remain accurate, CAMI recommends yearly calibration. However, depending on environmental conditions and usage, testers may need calibrating more or less frequently. Certain components within models M3U, M3UH, HVX, and HVX-21 (i.e. those capable of measuring resistance) are analog components whose characteristics change slightly over time. This aging is a natural phenomenon common to all electronic components and may cause resistance measurements or gradually deviate from normal. A tester that is out of calibration will give inaccurate results. Some (maybe all) resistance measurements will be incorrect. Consequently, it may Pass what should Fail and, conversely, Fail what should Pass. In other words product yield will be contaminated due to unreliable quality.
-
5200 Advanced -
Rhesca Co., Ltd.
This is an ultra-high-sensitivity wettability tester developed to evaluate the solder wettability of ever-miniaturizing electronic components. Electronic devices, especially mobile devices, are becoming more compact and multi-functional. As the number of electronic components mounted on them increases and the pitch of connectors that connect each device increases, soldering parts are becoming increasingly miniaturized. expected to respond to further miniaturization of electronic components and miniaturization of joints in the future .
-
GLP3 -
Schleich Gmbh
The GLP3-Windows®-testers are our premium testers to test a variety of different complex products. They are preferably used to test electric component groups, run-in test benches, power supplies, cables, washing machines and more and are ideally suited for complex test benches and inerlinkes assembly- and test lines.
-
CX-Q002 -
Shenzhen Chuangxin Instruments Co., Ltd.
Ball Pressure Tester is used for testing parts of non-metallic materials for resistance to heat. It is applicable to electrotechnical equipment, its subassemblies and components, and to solid electrical insulating materials except ceramics.
-
-
DWX Series -
ECG KOKUSAI Co., Ltd.
The DWX tester is designed to test other coils and low inductance coils used in high-end electronic components. Through the use of impulse power source with high-speed switch, highly efficient input circuit, and high-speed A/D sampling circuit, the DWX tester can offer a new solution to the low inductance coil tests.
-
Lorlin Test Systems
The Double-Impact Discrete Component Tester is designed to test small signal and power semiconductor components in both single and multi-device packages or hybrids.. The system uses a Windows 10® 64-BIT OS and a USB 2.0.
-
TIME®5100/5102/5104 -
Beijing TIME High Technology Ltd.
Pen Type Hardness Tester TIME®5100/5102/5104 is economically priced and suitable for quick hardness testing on metal materials, especially on-site hard testing of large, non-transportable components.
-
TIME®5106 -
Beijing TIME High Technology Ltd.
TIME5106 dynamic type hardness tester is integrated with impact device G for testing solid components like heavy castings and forgings. It can perform hardness test in individual mode or in system mode.
-
PS-355 -
PINTEK Electronics
*HOLD-OFF, X-Y OPERATION.*1mV/DIV SENSITIVITY.*10nS/DIV RESOLUTION.*COMPONENT TESTER.*BEAM-FINDER, ILLUMINATE.*WITH DELAY SWEEP.*TWO SWEEP MIX FUNCTION.*CE, TUV GS, UL CUL, IEC1010
-
UniTest Inc.
The module tester tests the modules in which the final tested components are assembled together. This test is also one of the most important factors to guarantee the quality of the products. DDR, DDR2, DDR3, FBDIMM,
-
1689 -
IET Labs
The GenRad 1689 Precision Impedance Meter gives you the best performance for your most demanding applications whether they be production test, incoming inspection, component design and evaluation, process monitoring or dielectric measurement. It is a versatile, full function microprocessor-based passive component tester that's available in a rack mountable, (1689M) model.
-
TH2684A -
Changzhou Tonghui Electronic Co., Ltd.
TH2684 High Precision IR Tester is an intelligent measurement instrument that is used for rapid measurement on IR Tester is an intelligent measurement instrument that is used for rapid measurement on IR properties of electronic parts and components, dielectric materials, equipments, cables, etc. Large LCD and user friendly menu provide you easier operation.
-
TH2684 -
Changzhou Tonghui Electronic Co., Ltd.
TH2684 High Precision IR Tester is an intelligent measurement instrument that is used for rapid measurement on IR Tester is an intelligent measurement instrument that is used for rapid measurement on IR properties of electronic parts and components, dielectric materials, equipments, cables, etc. Large LCD and user friendly menu provide you easier operation.