Showing results: 2281 - 2295 of 2772 items found.
-
KRD31 series -
CME Technology Co. Ltd.
KRD31 series constant acceleration tester are used to test articles under extreme acceleration conditions based on standard like MIL-STD-810F, MIL-STD-202 and IEC68-2-7. It is most suitable for testing electronic components or devices. Under high g effect on microcircuits, to check adaptability and reliability of wiring and the internal structures. It may expose mechanical and structural defects that are not found with vibration and shock tests.
-
National Technical Systems
According to the best meteorological estimates, the surface of the earth is struck by lightning approximately 100 times each second, which averages out to about 8 million strikes per day. In addition, the Federal Aviation Administration reports that the average commercial aircraft gets hit by lightning on average about once for every 1,000 hours of flight it completes, which amounts to approximately once a year.With statistics like these, it’s obvious that providing adequate lightning protection to electrical components is crucial — whether that’s onboard an aircraft or as part of a ground-based facility. Fortunately, at NTS, we’ve been helping companies do just that for well over 50 years. Thanks to our lightning simulation and modeling services, companies are able to develop high-quality products that meet with their respective compliance regulations — from military and defense to Airbus and Boeing published standards.
-
Pasternack Enterprises, Inc.
Pasternack's low phase noise amplifiers cover select frequency bands ranging from 1.5 to 18 GHz with residual phase noise levels as low as -180 dBc/Hz @ 10 KHz offset. Additional performance specs include small signal gain ranging from 9 to 14 dB, with typical noise figure of 5.5 dB. Psat levels for these amplifiers range from +16 to +25 dBm with Output IP3 levels as high as +34 dBm. All models feature single DC voltage supplies and input/output RF ports are internally matched for 50 ohms with DC blocking capacitors. These compact module assemblies require no external components and are available in rugged Kovar metal drop-in packages that are gold-over-nickel-plated and support field replaceable SMA connectors. All models are EAR99 and guaranteed to meet MIL-STD-883 test conditions for hermeticity and temperature cycle.
-
Pasternack Enterprises, Inc.
Pasternack 2.92mm adapter category is mostly RoHS and REACH compliant. 2.92mm adapter components are part of a complete adapter product line from Pasternack. 2.92mm adapters in straight or right angle versions are in stock and ready for shipment.Our 2.92mm adapter series allow you to interface 2.92mm connectors with 1.85mm, 2.4mm, 2.92mm, 3.5mm, 7mm, Mini SMP, N or SSMA connectors. 2.92mm adapters are available in female to female, female to male, female to sexless, male to female, male to male or male to sexless gender combinations. The 2.92mm adapter category includes bulkhead, 4 hole panel or mountless configurations.Our ISO 9001:2008 registered facility ships 2.92mm adapter parts the same day from the broadest and deepest in stock inventory of RF and microwave parts. Exceptional customer service and technical support are on hand to help you.
-
Teledyne OEM Solutions
All components and subassemblies receive the highest attention to detail and workmanship, ensuring your satisfaction. From the initial design phase through to the final assembly, we are committed to producing the best possible products for our customers. Our team of skilled builders and assemblers take pride in their work and are committed to producing the best possible products.We thoroughly test and inspect all of our products before they leave our facility, and we stand behind their quality and workmanship. We are confident that you will be satisfied with your purchase, and we ensure that every product meets our high standards of quality control before it is shipped.If you have any concerns about the quality of your product, please don't hesitate to let us know. We are always happy to address any issues and ensure your complete satisfaction with our products.
-
Applied Image, Inc.
There are two SINE Sinusoidal arrays designed for FBI applications: the SINE M-13-60-S-RM and the SINE M-13-60-FBI Kit.The SINE M-13-60-S-RM was designed jointly by the Federal Bureau of Investigation, of Washington DC, and MITRE, of Bedford MA. The primary function of this Target is for computing Modulation Transfer Function (MTF) evaluation in live scanner fingerprint systems for conformance to Integrated Automated Fingerprint Identification Systems (AFIS) image quality requirements. The array is on reflective material measuring 16mm x 16mm with sinusoidal arrays ranging in frequency from 1.0 to 10.0 cycles per mm; with nominal modulation of the sinusoidal areas at 60%. The top and bottom rows are density scales, from 0.20 to 1.20 densities.The SINE M-13-60-FBI Kit consist of two individual components, the SINE M-13-60-1X-RM and the RR1-N-RM Ronchi Ruling grating.
-
Q-400 -
Dantec Dynamics A/S
The Digital 3D Image Correlation System Q-400 is an optical measuring device for true full-field, non-contact, three-dimensional measurement of shape, displacements and strains on components and structures made from almost any material.The Q-400 system is used for determination of three-dimensional material properties in tensile, torsion, bending or combined tests. In addition, deformation and strain analysis can be applied to fatigue tests, fracture mechanics, FEA validation, and much more.
-
Acroname, Inc
As part of Acroname's MTM series, the MTM-IO-Serial module is a key component to manufacturing test systems for electronic devices using a standard USB 2.0 interface, serial UARTs and one or more interface voltages. The MTM-IO-Serial module features a software controlled USB hub (USB 2.0 high-speed) with four controllable channels. Each channel has switched data and 500mA current-limited power lines.
-
National Technical Systems
The use of Scanning Electron Microscopy / Energy Dispersive X-Ray Spectroscopy (SEM/EDS) in the analysis of failure related issues of printed circuit boards (PCBs), assemblies (PCAs), and electronic components (BGA, capacitors, resistors, inductors, connectors, diodes, oscillators, transformers, IC, etc.) is a well-established and accepted protocol. As opposed to or simply in addition to normal optical microscopy, SEM/EDS allows for the “inspection” of areas of interest in a much more informative way.
-
DYNA4 Framework -
TESIS DYNAware Technische Simulation Dynamischer Systeme GmbH
DYNA4 is a modular simulation software for efficient work with simulation models in the automotive development process, e. g. of electronic control units and components. Model-based design, function development. Testing and pre-calibration in SIL and HIL environments. Fail-safe and functional tests, including evaluation of vehicle response and drivability. Advanced powertrain development and energy management. Fuel efficiency simulation for hybrid (HEV), electric (EV) or traditional vehicles.
-
TTC/CTC -
Memmert GmbH + Co.KG
Rapid, precise and energy-saving temperature changes in the range from -42 C to +190 C, along with fast humidity recovery times, make the TTC temperature test chamber and the CTC climatic test chamber with humidity unit a perfect duo for controlled material testing, function tests, ageing tests or climate tests on composites, concrete, plastics or electronic components in material technology, the automotive and aerospace industries, and electronics.
-
Kikusui Electronics Corp.
The KES7000 System is a conductive immunity test system that is fully compliant with ISO7637-2 and ISO7637-3, international standards for EMC testing required for automotive electronic components. This system consists of the KES7700 Series Transient Surge Tester, KES7400A Series Voltage variation simulator and KES7100 application software dedicated to the KES7000 system. This product configuration supports JASO standards and the special test requirements of car manufacturers with options or custom orders.
-
ES4640 -
ETAS GmbH
The ES4640 Connector Box offers a standardized wiring and connectivity for HiL testing systems in the powertrain domain. Its front panel provides connectors for the ECU, CAN bus communication, on-board diagnostics, and LEDs for ignition and injectors. Its rear panel connects loads, failure simulation, and other components. Sample applications of the ES4640 are closed loop HiL systems for 8 cylinder gasoline and diesel engine ECUs.
-
TMD Technologies Ltd
EMC HIRF testing – meeting the most demanding RTCA/DO-160 requirementsScientific ResearchHigh Power Component Testing (PIM Testing)Medical LINACSRecent developments include a range of Ultra High Power HIRF amplifiers achieving generally over 10 kW. EMC test laboratories using TMD Amplifiers have generated 14,000 V/m, easily complying with the latest, most demanding RTCA/DO-160 requirements.
-
Omegameter SMD 650 -
Specialty Coating Systems
The SCS Omegameter SMD 650, the long-time industry standard for ionic testing utilizing “static test” methodology, is designed to perform cleanliness testing on printed circuits and assemblies. Identifies the presence of ionic contamination on bare and assembled printed circuit boards and other electronic components. Provides an accurate and repeatable method for determining cleanliness on site. Provides immediate process control results, eliminating the need for outside laboratory testing.
