Filter Results By:
Products
Applications
Manufacturers
Component
Testing of individual hardware or software components or groups of related components.
-
product
Withstand Voltage Tester
2672AM
Shenzhen Chuangxin Instruments Co., Ltd.
Withstand Voltage Tester is used to measure the dielectric (withstand voltage) strength, which can be intuitive, accurate and fast tested the electrical safety performance indicators of the object, such as the breakdown voltage, leakage current etc. And Withstand Voltage Tester can be used as a high voltage source to test performance of the components and whole machine.
-
product
Linear Motion Potentiometers
A spin-off of the Trimpot trimming potentiometer product line, the linear motion potentiometer was developed to meet the needs of designers wishing to detect movement of position. Applications for these compact components include: Solenoid positioning sensors for automated controllers, volume control on audio equipment, joystick controllers, satellite dish positioning, and robotics.
-
product
Bus Management Test System
Solution to test redundant Architecture of BMUComprehensive test system performing tests of > 3000 I/O's Special test circuits using hybrid / ceramic components to operate in Thermovac chamber Tests various subsystem functionalities like, AOCS, Sensor Electronics, Telemetry, Tele-command with Self test and application test software
-
product
HV DC Voltage Generators
Fivestar HV Testing Equipment Co., Ltd.
HV DC voltage generators are used to generate high voltage DC test voltages for routine, type and development test on components and complete systems found in electrical power supply systems and operating on DC voltage (HV transmission systems etc). There are K and M series, and available for indoor and outdoor.
-
product
Dielectric Fault Analyzer
DFA100
The DFA100 Dielectric Fault Analyzer is a handheld survey tool used to identify and locate partial discharge, particles, and mechanical defects.With three measuring modes, continuous, phase and pulse, the DFA100 uses its acoustic emission sensor to find in-service acoustic signals produced by partial discharge and loose components.
-
product
Strain Measurements and Experimental Stress Analysis
Experimental structural testing using strain gauges is necessary in a wide range of applications from airframes and sub-assemblies down to individual components such as turbine blades, satellites, wind turbines, buildings, bridges and many others. These tests enable the engineers to compare the acquired data with the predicted results from the design calculations.
-
product
Tensile Test Chamber
CSZ's Tensile Test Chamber is an environmental chamber that interfaces with a customer tensile tester load frame. This chamber is required to expose various materials and components to temperature conditions while undergoing tensile test. Tensile testing stresses materials by pushing, pulling, twisting, or bending intended for static and fatigue testing.
-
product
Agree Test Chambers
Agree test chamber are designed to perform specific temperature, humidity and vibration test to improve the quality and reliability of components. The Agree method of testing is an acronym for the Department of Defence Advisory Group Reliability of Electronics Equipments. This chamber also known as Temperature Humidity Vibration Test chamber and Stress Test Chamber
-
product
Flex Test Fixtures
FTFs are test fixtures which are dedicated for testing flex-based components and assemblies such as displays, touch panels and more. A weak spot in a typical functional test system is the method to connect DUT flexible cable to a circuit board where the simple method of attaching the flex directly with an ZIF or LIF connector fails.
-
product
Spin Testers and Bearing Assemblies
Vidac has created several spin test systems ranging from the basic manually operated model shown here to fully automated machines that can spin the customers components to a specific speed profile. Our 3D design capability ensures the tight tolerance fit required for high speed rotation.
-
product
High Voltage AC Test Systems
Our range of high voltage AC test systems cover from 5kVac to 100kVac. All units have a variable trip range setting and key lock operation to prevent unauthorised use. Applications include testing of insulation systems and measurement of break down voltage of electrical plant and components.
-
product
Microwave System Amplifier, 2 GHz To 8 GHz
87415A
The Keysight 87415A microwave component amplifier brings compact, reliable gain block performance to systems integrators and microwave designers. With 25 dB minimum gain and over 23 dBm output power from 2 to 8 GHz, this amplifier offers output power where it is needed: at the test port.
-
product
LXI Microwave Matrix
Pickering's LXI Microwave Matrix is a 2U full rack width unit that provides a compact microwave switching solution for automatic text equipment (ATE) systems. The matrix is fully configured to the specified dimensions with no extra cabling needed; saving users the cost and time of creating matrices from individual components.
-
product
Systems Integration (SIL) Lab Data Acquisition
Bloomy’s SIL data system allows testing and simulation of every system component on the aircraft. The functionality of these complex integrated systems are fully tested, debugged, and verified safely in the lab prior to flight testing. This reduces cost and schedule for new aircraft. Bloomy has applied its expertise to multiple SILs.
-
product
Bench Meters
LCR Meters
The measuring objects of LCR Meters are the parameters of impedance components, including resistance R, inductance L, quality factor Q, capacitance C and loss factor D. The selection of digital bridge should consider the highest frequency, test accuracy, test speed and DCR test function of the tested device.
-
product
Hydraulics Testing
Fluid power systems play a critical role in many industries, and are one of the three major forms of power transmission along with electrical and mechanical power systems. In many cases, however, mechanical and electrical methods cannot provide a practical power transmission solution. In these cases, fluid power (whether hydraulic or pneumatic) is often used because it can deliver linear and rotary motion with high force and torque within a smaller, lighter package than is possible with other forms of power transmission. Some of the most common applications of hydraulic systems are in heavy construction and off-highway equipment. Other applications can be seen in aircraft, mass transportation systems (such as trains), construction, mining, agriculture, waste reduction, and utility equipment. The various components (such as valves, actuators, cylinders, accumulators, etc.) that make up these systems must perform reliably and have a reasonable life span. Only a thorough test program carried out under simulated field use conditions can insure that any component part or assembly will meet its original design goals for performance, reliability and longevity. Many internationally recognized organizations have published test standards that apply to hydraulic/pneumatic and fluid power systems and components. Some of these organizations are:
-
product
Walk-in Environmental Chamber for Temperature Humidity Test
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's walk-in environmental chamber for temperature humidity testing is perfectly meet the large size test application that require high temperature and high humidity. The walk-in chamber is constructed with structural steel, so it is able to test the large components and products. Various optional function available for different test standard and requirement.
-
product
Fully Automatic Eddy Current Crack Test System
ROTO-PUSH
Foerster Instruments, Incorporated
The ROTO-PUSH test station, which is integrated in production lines, serves to test cylindrical components for cracks in the liner surface. The testing configuration has to be rotated for automatic crack testing. After the test, the test pieces are sorted and separated. The continuous test run ensures a high testing rate, which increases profitability.
-
product
Sand and Dust Environmental Test Chamber
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Sand and dust test chamber is suitable for all kinds of automotive parts dust-proof, dust resistance test. Test components including automotive lights, instrumentation, electrical cover, switch system, door lock, etc., and test its sealing performance. Besides, it also has view window with illumination.
-
product
ChemWiz Analyzer Development Kit
Full spectrum chemometric analysis for multiple components can now be performed using the ChemWiz® Analyzer Development Kit (ADK). This software toolkit, when combined with StellarNet spectrometer instrumentation and SpectraWiz operating software, enables rapid development of complex analyzers needed to provide custom measurement solutions for many applications.
-
product
Leak Masters
Uson provides automatic non-destructive air leak and flow measurement equipment and solutions used in product development and manufacturing environments for medical device, automotive, electric vehicle battery, packaging and industrial applications. Uson leak testers are highly configurable and are built with premium components ensuring maximum quality, reliability and performance.
-
product
Generators and Sources
For general purpose standalone applications or as core components in a high speed test and measurement system, Yokogawa sources and signal generators are highly accurate and functional. The integration of source and measurement into a single unit greatly simplifies the test process. Semiconductor devices, sensors, displays or batteries etc can therefore be quickly and easily characterized.
-
product
Video Signal Generator
MSPG-8100S
MSPG-8100S various standard signal. (HDMI, DISPLAYPORT, DVI, VGA, COMPONENT, CVBS, S-VIDEO, SCART) So, It is a fundamental equipment of develop display. (LCD TV, LED TV, Monitor, Project) MSPG-8100S designed supports 4Kx2K/60Hz resolution by HDMI/DISPLAY ports and it can test 3D and ARC(Audio Return Channel) function.
-
product
Colorimetry, Turbidity & UV-Vis Spectrophotometry
Colorimetry, turbidity, and spectrophotometry meters for water analysis. You can choose from 134 preprogrammed methods to measure the concentrations of sample components with our colorimetry meters. These portable meters can go with you anywhere to test drinking water or wastewater. Take your portable turbidity meter to the source for on-site measuring. Our turbidity meters feature white and infrared light sources allowing you to meet regulatory methods. Achieve simple and efficient water and wastewater analysis with our UV-Vis and Vis spectrophotometers. These meters include over 260 preprogrammed methods using common reagent chemistries, making them the ideal instruments to include in your laboratory.
-
product
EMC Tests
Electromagnetic compatibility (EMC) must be demonstrated for all devices with integrated radio components for approval in almost every country in the world. EMC tests examine whether the electromagnetic emissions from your product are within the specified limits and whether your product and its functionalities themselves are not negatively influenced by electromagnetic emissions. We offer EMC tests for modules and end products with integrated radio technology as well as IT and IoT products. Our accredited EMC test laboratories are equipped to test almost all modern radio technologies, and our EMC experts have many years of experience in this area. With us, your modern radio products are on the safe path to the global market.
-
product
EPON OLT ( Optical Line Termination )
OLT-1408
Hangzhou Huatai Optic Tech. Co., Ltd.
OLT-1408's Optical Line Terminal (OLT) adopts GiGA Ethernet Passive Optical Network (EPON) technology. It is a compact chassis with L2/L3 GiGA switching and routing function. All the functional components are modularized design and it supports hot-plugging with plugging and playing. 1~4 pieces of GiGA optical port or electrical port are optional in the uplink port, which provides a direct optical interface for the Ethernet/IP network core. 1~8 pieces of EPON optical port are optional in the down link port. Through a passive optical Network (PON), an optical Network unit link (ONU),it can provide final transmission with bandwidth up to 1Gbps for the user.
-
product
Field Strength Meter
SMP2
2-in-1: broadband measurements (1 Hz - 18 GHz) and spectrum analysis (1 Hz – 400 kHz)Real-time FFT-based spectrum analysis using digital processing.Weighted Peak Method (WPM) for automatic and real time comparison with limits.Special auto-gain function for peak detection (indispensable for procedures such as welding).Display of results in RMS and peak values.Function for time domain measurement of a specific frequency.Automatic field probe recognition.E&H field selection.Total field value and value for each component (X, Y, Z).Frequency SPAN selection.High Pass Filters at 1 Hz, 10 Hz, 25 Hz and 100 Hz.Max-hold function.Display of maximum, minimum and average
-
product
Qseven Module With Intel® Pentium® Processor N4200 & Celeron® Processor N3350
Q7M311
The Q7M311 has adopted the 14nm Intel® Pentium® N4200 and Celeron® N3350 quad-core/dual-core processors (codename: Apollo Lake). The extremely small embedded module supports 4GB (or optionally up to 8GB) DDR3L memory onboard and 32GB eMMC flash memory (optional). With a seismic design and for industrial-grade temperatures, both the CPU and the DDR3L RAM are soldered to deliver reliable and excellent computing performance. With rich features embedded in all the components built in a small form factor, the industrial-grade computer-on-module is aimed for industrial IoT applications, including industrial control, medical imaging, digital signage, gaming machines, military, and networking.
-
product
Sound Level Meter, 35 dB, 130 dB, 5 dB, 0.1 dB, 0 °C, 50 °C
72-6635
*Large LCD Display, easy to read*Characteristic of "A" frequency weighting network are designer to meet IEC 651 type 2*Fast time weighting characteristic mode*Build in adj. VR is available for easy calibration*Condenser microphone for high accuracy & long-term stability*Hold function to freeze the display value*Warning indicator for over and under range*LCD display for low power consumption & clear read-out even in bright ambient light condition*Durable, long-lasting components, including a strong, light weight ABS plastic case*Small and light weight design allow one hand operation*Low battery indicator*High quality with economical cost
-
product
Text Analysis
Text analytics is the process of transforming unstructured text documents into usable, structured data. Text analysis works by breaking apart sentences and phrases into their components, and then evaluating each part’s role and meaning using complex software rules and machine learning algorithms. Data analysts and other professionals use text mining tools to derive useful information and context-rich insights from large volumes of raw text, such as social media comments, online reviews, and news articles. In this way, text analytics software forms the backbone of business intelligence programs, including voice of customer/customer experience management, social listening and media monitoring, and voice of employee/workforce analytics.