Filter Results By:
Products
Applications
Manufacturers
Component
Testing of individual hardware or software components or groups of related components.
-
product
IEC60529 IPX9K Waterproof Test Chamber
CX-IPX9
Shenzhen Chuangxin Instruments Co., Ltd.
The main purpose of the equipment is to test product performance of storage, transportation and use in the rain condition.The equipment, mainly used in electronic and electrical products, lamps ,lanterns, electrical cabinets, electrical components, automobiles, motorcycles and their parts etc, tests physical and other related properties of products by simulating the rain condition.After test, judge if the performance of the product meets the demand by verification for product design, improvement, check and factory inspection use.
-
product
Hydraulic Servo Control Compression Testing Machine (Four Column)
TYE Series
Jinan Testing Equipment IE Corporation
This series Servo-Hydraulic Compression Testing Machine is mainly designed for compression test of building material items, such as concrete cubes, cement specimen, paver materials and related component, etc. With new design idea and advanced technolog, this series has more advantages in appearance, operation & applications. The compression testing machine is an ideal tester for quality control at industrial & mineral enterprises, teaching in high schools, and technology researching at scientific institutes.
-
product
Digital Telemetry Solutions
For measurements on rotating components and moving machinery, imc offers modern telemetry systems for a wide variety of tasks: whether single-channel torque monitoring of a rotating shaft, multi-channel strain gauge and temperature measurements on a train wheel-set or non-contact power measurement on a vehicle drivetrain in harsh environments. There are transmission electronics available for a large variety of sensors, such as strain gauge (quarter-, half- and full-bridge), thermocouples, PT100/1000, as well as IEPE sensors and voltage signals.
-
product
Thermal Shock Chambers
VTS-Series
Vertical Thermal Shock chambers consist of two separately controlled hot and cold zones. Product is transferred between these zones for rapid product temperature changes. Thermal Shock Chambers are designed to perform tailored environmental stress screening of component and board level electronic assemblies. The return on investment in both actual savings and customer confidence adds greatly to the value of electronic assemblies screened in a CSZ thermal shock system.
-
product
PCB Pushing Mechanism
Two pushers plate available for max. DUT areas: 450×450 and 500×650 mm 6tl precision servo pusher H7100 6000 is the recommended solution for PCB test systems combining Functional, In-Circuit, and Hipot Test in one fixture.It is available as a 19″ Rack atonomous module, including all drive, control and safety components for easy integration in automatic test systems using standard Mass Interconnection Receivers.
-
product
60 GHz Transmitter and 60 GHz Receiver Modules
The 60 GHz transmitter and 60 GHz receiver modules open up ultra high speed, high bandwidth data transmission for widespread use. Pasternack 60 GHz waveguide modules utilizes the globally unlicensed millimeter wave spectrum of 57 GHz to 64 GHz. Our wireless 60 GHz waveguide transmitter and receiver components are ideal for meeting the high speed data transmission needs of companies and developers.
-
product
Software Test Framework for LabVIEW
VI Tester
VI Tester is a software test framework for LabVIEW that allows software developers to test their LabVIEW code (VIs). Software testing is a critical component of agile development and test driven development processes and is also critical for validating software functionality. VI Tester is based on the industry standard xUnit software test architecture that is used in many other programming languages. This architecture is very flexible and powerful, but also very easy for beginners to learn.
-
product
Physical
This category covers test equipment for verification of resistance to heat, fire, tracking, mechanical stress, endurance, impact, force, torque, dimensional accuracy & similar related parameters as required by national and international safety regulatory agencies. These equipment are used to check Electrical WiringAccessories, Electrical Home Appliances, Industrial Luminaires, Motors and components or parts used in such products. Many of these test equipment are common to many standards and are essential for routine test purposes.
-
product
Environmental Test Chambers
CSZ offers a large selection of environmental test chambers with quality construction and innovative technology, serving a variety of industries. Temperatures range as low as -84C (-120F) with high temperatures to +350C (+662F) and humidity ranges from 10% to 98% RH. Test chamber sizes range from small benchtop chambers for testing small components to full walk-in/drive-in rooms large enough to accommodate a semi-truck and trailer or larger.
-
product
Sand & Dust Testing
Products with moving parts, electromechanical components, filtering systems and electronics are all susceptible to fine and large particle dust that can contaminate a product. These contaminates can cause premature failures and loss of function.Today’s test plans for phones, computers, vehicles, enclosures and aircraft include sand and dust testing to determine if this stress source would cause functional deterioration.Our services include military and automotive dust testing for both blowing and agitated dust and sand.
-
product
PNA-L Network Analyzers
The Keysight PNA-L network analyzers help you with your general-purpose network analysis needs. The PNA-L network analyzers give you efficiency and flexibility in both manufacturing and R&D applications. The PNA-L VNA covers various industries ranging from mobile telecommunications, wireless LAN component production, and aerospace and defense. The PNA-L network analyzers balance value and performance using the Keysight PNA network analyzer's core firmware.
-
product
Coaxial Dual-Directional Coupler, 2 GHz to 18 GHz
772D
The Keysight 772D is a high-performance, dual-directional coupler designed for broadband swept measurements in the 2 to 18 GHz range. This coupler can be combined with Keysight power sensors and power meters for reflectometer applications. Forward and reverse power measurements on transmitters, components, or other broadband systems are made simpler using the Keysight 772D. The broadband design allows the use of a single test setup and calibration for tests spanning the entire 2 to 18 GHz range.
-
product
Adapter/Stainless Steel
WADP-24FSM
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customers demand. All Warisons products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
product
Adapter/Stainless Steel
WADP-24M35F
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customers demand. All Warisons products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
product
Manual Step Attenuator
WATT-3SM352
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customers demand. All Warisons products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
product
Mini Cable Splice Tool Kit
OMK-SR-MCS
The OPTOKON OMK-SR-MCS Mini cable splice tool kit offers all necessary tools and components for field usable, quick repairs of cables in the toughest of environments. Utilising the proven mechanical splice in both singlemode and multimode applications, there is no need for power, heat or complicated termination procedures. Based on standard mechanical splice technology of the MCS-04, the tool kit provides low loss fiber jointing in just a few minutes. Cable retention and tie off is achieved through the aramid yarn and IP 67 guaranteed in the same way as connectors. With a small diamensions the Mini Cable Splice provides a permanent join of ruggedized cables up to 4 fibers. Purchased with all the tooling and consumables necessary to carry out the operation, the kit comes complete with splice unit, ready for use in a rugged field usable carry case. Splice unit, spares and consumables are then replaced and replenished at a low cost whenever necessary.
-
product
AMIDA 3KS Tester
The AMIDA-3KS test system provides a lower cost, cost-optimized test solution for all consumer power management ICs and portable product components. The AMIDA-3KS tester provides 6 board slots in the test head for the required number of analog board channels, thus reducing the overall system procurement cost, making the cost-effectiveness of each board channel 2 times higher and more flexible. The customer's product testing time is greatly shortened.
-
product
DC Electronic Load
DC electronic loads are designed for testing a wide range of power conversion products including AC/DC and server power supplies, DC/DC converters, EV batteries, automotive charging stations, and other power electronics components. These units can be synchronously paralleled up to 240kW and dynamically synchronized for generating complex multi-channel transient profiles. The 300% peak overpower capability provides extra headroom for fault condition simulations in automotive batteries, fuel cells, and more.
-
product
Compact Environmental Chambers
MicroClimate 3
The MicroClimate 3 is a compact environmental chamber designed to simulate a full range of temperature and/or humidity conditions. The small footprint of the MicroClimate 3 combined with temperature and humidity capabilities make this chamber the number one choice for testing small components and products. Whether you need to perform temperature cycling tests or expose your product to steady state temperature environments, these chambers will maintain precise and accurate temperature/humidity control throughout your test.
-
product
AC Test Transformer
Yangzhou Power Electric Co., Ltd
The AC test transformer are especially designed for testing high voltage products and components, such as cables, power transformers, gas-insulated switchgears, bushings and arresters. It is also suitable to test insulation materials. They are used to generate testing high voltage and function as part of the complete system. These systems are particularly suited for tests requiring stable voltage even if the load changes under voltage (corona, wet & pollution tests) or when the load is inductive (inductive voltage transformers).
-
product
Load Cells
The heart of each weighing system is a load cell. Load cells are mechanical components which act as force sensors by employing strain gages to provide an electrical output proportional to the applied force. Typically the electrical output is either analog (voltage or current) or digital. Load cells have specific mechanical packaging and sensing orientation to fit into electronic scales, and testing and monitoring systems. Load cells can be used for tension, compression, and/or shear measurement.
-
product
Signal Generator, Audio, Compact, Handheld, 1 Channel, 20kHz, FM, US Plug
72-490
Highly versatile compact audio generator is perfect for sound system and speaker component testing. Its high precision and remote VCO input make it suitable for the serious test environment, yet its compact size and low cost make it suitable for any tool box. This device is designed to be connected to the line level of any consumer or commercial designed audio amplifier. While it is designed to be used with unbalanced inputs, it is also suitable for balanced equipment
-
product
Vsync™ Controls Platform
Vsync™ is RedViking’s 4th generation powertrain dynamic testing software, based on over 100 fielded dynamic component test benches. Developed by RedViking for aerospace, automotive and off-highway test labs. Your lab or end-of-line test stand won’t have to rely on multiple stand-alone systems with limited data acquisition and analysis capabilities. Vsync™ provides an integrated, user-friendly platform for indisputable test data with superior repeatability and traceability.
-
product
Robotic Intelligent Laboratory System
CHANGSHA KAIYUAN INSTRUMENTS CO., LTD.
Is able to determine calorific value, total sulfur, internal moisture, ash, volatile matter, CHN content and other indicators by robot technology. The main components include intelligent robot, automatic analytical instruments (calorimeter, sulfur analyzer, proximate analyzer, and elemental analyzer), automatic bottle opener and sampling device, automatic weighing device, oxygen vessel loading and cleaning device, electrical control system, and laboratory analysis and data management software.
-
product
Transformer Turns Ratio Meter
We are considered as one of the leading manufacturers and exporters of Transformer Turns Ratio Meter With/ Without Phase. The equipment is widely used in power generation and engineering industry for testing of transformers. We engineer and develop this testing equipment in accordance with industry standards using best grade components and raw materials. This Transformer Turns Ratio Meter With/ Without Phase can be also optimized according to client's specific requirement. We offer this testing equipment at competitive price.
-
product
High Current Test System
HIGHVOLT Prüftechnik Dresden GmbH
High current test systems are used to test the thermal stability of equipment and components. The test system induces a current in the test object causing it to heat up. Therefore, the test object is designed as a shorted circuit. The high current test system measures the temperature of the test object at various points, in addition to the current. As a special feature, the temperature that the test object should reach can be specified and the amount of the current can be automatically calculated by the HIGHVOLT test system.
-
product
Electronic Transformer Test System
UI2000-ET
• Input characteristics analysis 1) Measure Vrms (10-300V) Lrms (0.04-4A) W, PF, Hz, total harmonic and 0-50 component of harmonic 2) Accuracy: ± (0.4%reading + 0.1%range + 1digit) • Output characteristics analysis 1) Measure lamp voltage (1-60V) lamp current (03-20A) lamp power, crest factor and oscillatory frequency 2) Accuracy: Class 2 • It can print without compute, and provide the communication port for PC
-
product
Electrical Safety Tester
MST-8101/8103
Multi-channel output is an internal high-voltage switching module attached at the bottom of the instrument. Through multi-channel output module, multiple test points of the components can be connected with multiple channels at a time. During testing, the instrument can be set to control the channel switch. Controllable testing can be achieved by connecting the corresponding port to withstand voltage test terminal. With this multi-channel module, rapid connection can be achieved through test fixture without changing ports during the testing process.
-
product
External Frontend
FE50DTR
The R&S®FE50DTR external frontend can extend the frequency range up to 50 GHz for Rohde&Schwarz signal and spectrum analyzers as well as signal generators. The R&S®FE50DTR enables signal up and downconversion directly at the device under test (DUT), lowering cable losses, increasing sensitivity and delivering more power at the antenna in an OTA environment. With a dual connector system, testing of active components is an easy task.
-
product
TAP Signal Isolation Module
JT 2139
The JT 2139 is a TAP signal isolation module designed for use in combinational test systems that utilise multiple instrument interfaces. To avoid parasitic capacitance effects and/or unwanted ground loops the JT 2139 can be used to completely galvanically isolate any JTAG Technologies boundary-scan controller from the remainder of the instrumentation system. JT 2139 isolators are a standard component of the JTAG Technologies ‘Symphony’ systems that integrate boundary-scan with In-Circuits Testers etc..