Showing results: 2101 - 2115 of 2906 items found.
-
40-971B-200-1m-MM -
Pickering Interfaces Ltd.
This male rear exit to ribbon cable 1m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin male 2.54mm pitch IDC connectors. The 200-pin connector can be secured to the product by male screwlocks. This assembly can be used for applications requiring unterminated cables, simply crop off the ribbon cable headers.
-
40-971B-200D-2m-MM -
Pickering Interfaces Ltd.
This male rear exit to D-type 2m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-Pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin male D-type connectors. The connector can be secured to the product by screwlocks. The cable assembly can be used with Pickering's 50-Pin D-Type connector blocks (refer to 90-005D). Each of the four D-type cables is numbered to allow identification.
-
North Atlantic Industries
NAI offers, and continues to introduce, high density multifunction or combination-function I/O boards designed for a specific application or purpose. Based on the specialized application itself, from the interface connectors through the motherboard, to the specific function, these boards typically address I/O function integration challenges requiring higher current capacity, layout, and/or grounding requirements that are not available in our standard I/O boards. They are specifically designed for rugged defense, commercial aerospace, and industrial applications.
-
11854A -
Keysight Technologies
The Keysight 11854A accessory kit furnishes the RF components required for measurement of devices with 50 ohm, BNC connectors and when using a network analyzer with a type-N configuration. The BNC accessory kit contains two type-N male to BNC female adapters, two type-N male to BNC male adapters, two type-N female to BNC female adapters, two type-N female to BNC male adapters, a BNC male short, and a storage case.
-
8491A -
Keysight Technologies
The Keysight 8491A coaxial fixed attenuator provides precision attenuation, flat frequency response and low SWR over broad frequency ranges. The attenuator has type-N connectors and is available in nominal attenuations of 3 dB and 6 dB, as well as 10 dB increments from 10 dB to 60 dB. This attenuator is swept-frequency tested to ensure specification compliance at all frequencies. Calibration points are provided on a nameplate chart attached to each unit.
-
40-971B-200D-1m-MF -
Pickering Interfaces Ltd.
This male rear exit to D-type 1m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-Pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin female D-type connectors. The connector can be secured to the product by screwlocks. The cable assembly can be used with Pickering's 50-Pin D-Type connector blocks (refer to 90-005D). Each of the four D-type cables is numbered to allow identification.
-
40-971B-200D-2m-MF -
Pickering Interfaces Ltd.
This male rear exit to D-type 2m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-Pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin female D-type connectors. The connector can be secured to the product by screwlocks. The cable assembly can be used with Pickering's 50-Pin D-Type connector blocks (refer to 90-005D). Each of the four D-type cables is numbered to allow identification.
-
40-971B-200-2m-MM -
Pickering Interfaces Ltd.
This male rear exit to ribbon cable 2m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin male 2.54mm pitch IDC connectors. The 200-pin connector can be secured to the product by male screwlocks. This assembly can be used for applications requiring unterminated cables, simply crop off the ribbon cable headers.
-
785024-01 -
NI
100-Pin Female SCSI to 100-Pin Female Screw Terminal, DIN Rail, Wall, Pane Terminal. Block The SCB-100A is a shielded I/O connector block for interfacing I/O signals to NI data acquisition devices with 100-pin connectors. Combined with shielded cables, the SCB-100A provides rugged and protected signal connectivity. It has a mechanical enclosure that features a magnetic removable lid and pinout diagrams. It also includes pane, wall, and DIN Rail mount options.
-
dbSAFE Classic -
DVTest Inc.
Designed to be a utility enclosure for basic RF applications, the dbSAFE Classic has a wide operable frequency range offering up to 90db of isolation between 300MHz and 18GHz. Featuring the same durable aircraft-grade aluminium construction and precision machined I/O panels of the original dbSAFE, the dbSAFE Classic incorporates modern gaskets, absorbers, and interchangeable I/O panels. Added to that is the widest selection of I/O connectors and interface modules in the industry. The dbSAFE Classic will NOT disappoint.
-
SCANIO Family -
Corelis, Inc.
The Corelis family of SCANIO™ modules turn any IEEE standard 1149.1 boundary-scan controller into a powerful digital boundary-scan tester. The SCANIO family of products use boundary-scan gate arrays to add control and visibility to connectors, traces, and logic that can not be tested using traditional boundary-scan techniques.The SCANIO products, when combined with a boundary-scan controller, operate as a traditional “bed-of-nails” tester except access to the stimulus and response I/O’s is achieved via boundary-scan.
-
Teledyne LeCroy
The Teledyne LeCroy WavePulser 40iX and the Teledyne Test Tools T3SP15D are a perfect combination of complimentary products to serve the requirements on testing, validating and troubleshooting cables, backplanes, connectors, transmission lines on boards and interconnect.
-
VR300 -
Sundance Multiprocessor Technology Ltd.
The VR300 is a Test RTM, typically used during firmware and software development and debugging cycles on the VF360. The rear panel contains two mini-USB connectors, a Dual mini-SAS (SFF-8088) connector and a SFP case.
-
72-6290A -
Tenma
The 72-6290A is a multi-modular Cable Tester (LAN Tester) with LED meter display. Requires 9V battery for this modular cable tester. Used with RJ-45, RJ-12, RJ-11 connectors and USOC4, USOC6, USOC8 cables.
-
MS 1508 -
Meltronics Systemtech
- 32 Bit ARM9 LPC3250 Processor (256KB SRAM)- External memory (Flash – 2 MB, RAM - 512 KB, 8KB DPRAM)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 144 Digital IO Channels – (18 * 8 Configurable Ports)- 64 Analog Inputs (16 Bit, 1MSPS)- 16 Analog Outputs (16 Bit)- 2 RS232 Serial Ports- High Speed Logic Device with 1 M bit in system flash, 54Kbit - Block Ram and 11Kbit Distributed Ram- Power, Analog and Digital signals Interface Connectors (J1, J2 and J3 - 96 Pin Euro)- Data acquisition of all analog & digital channels- External Bus through Add on module (15 bit address bus and 16 bit data bus)- Transmission of 1Kbytes at 400us through Ethernet- Power Requirements: +15V/2.5A, -15V/2.5A and +5V/6A- Board Dimension is 366.72mm x 150mm- Portable and 9U 19” chassis mountable- Board has interface connectors in rear side as well as in front side- J1, J2 and J3 96 Pin Euro connectors at rear side and Ethernet, JTAG, RS232, USB connectors at front side