Showing results: 2611 - 2625 of 2906 items found.
-
80761 -
SYOPTEK INTERNATIONAL LIMITED
The Miller 400x Microscope helps inspect fiber optic connectors quickly and easily. Its ergonomic design and built-in features make it ideal for field and lab use. The microscope features a pressure-activated on/off switch, focusing wheel, eyepiece, auxiliary white LED light source rated for 100,000 hours, adapter tip for inserting ferrule and battery compartment. Includes 2.5mm universal adapter cap and zipper case.
-
PCAN MicroMod FD Digital 1&2 -
PEAK-System Technik GmbH
The PCAN-MicroMod FD breadboard can be purchased together with ready-to-use motherboards that provide peripherals for specific requirements. Spring clamp connectors are used to connect CAN, I/O and supply. The main boards PCAN-MicroMod FD Digital 1 and 2 focus on digital inputs and outputs, which are provided with the appropriate protective circuit. The digital outputs of Digital 1 are equipped with low-side switches and those of Digital 2 with high-side switches.
-
The Motwane Manufacturing Company
High contact resistance values are a definite cause of the failure or less than optimal performance in a wide variety of electrical devices. Contact resistance testing is therefore most critical to measure the resistance of electrical connections in switching devices, circuit breakers, isolators, busbars, relays, joints, connectors, cables, and cable joints. The device helps to find destructive or corroded contacts and hence protects substation devices from damage.
-
SFF 8639 Gen4 (U.2) -
SCHILLER AUTOMATION GmbH & Co. KG
The 8639G4-TPA-PR test adapter or test fixture kit facilitates Source and Sink compliance testing for SFF-Hosts and Devices. These SFF-8639 Gen4 fixtures utilize the multifunctional connector system supporting single/dual port SATA, dual and MultiLink SAS, and/or up to four (4) port PCIe device configurations. The SFF-8639 Gen4 receptacle fixture will accept devices with plug connectors that are in accordance with SFF-8482, SFF-8630, and SFF-8680.
-
786544-01 -
NI
PXIe, 2-Channel, 10 GHz PXI Optical to Electrical Converter—The CohSol O2EPXIe-1001-2 provides two DC-coupled photoreceivers that convert light with wavelengths from 750 nm to 1,650 nm into electricity at speeds up to 10 GHz. It offers multimode fiber with a 62.5 µm core and SC/PC, FC/PC, SC/APC, or FC/APC connectors. The CohSol O2EPXIe-1001-2 is ideal for reliable testing in manufacturing or research and development environments.
-
ASMB-815 -
Advantech Co. Ltd.
- ATX server board with Xeon® Scalable processors- DDR4 2933MHz RDIMM up to 768GB, support Intel Optane DC Persistent Memory- Five PCIe x8 or two PCIe x16 and 1 PCIe x8- Intel® X557-AT2 dual 10GbE ports- Eight SATA3.0 and one M.2 connectors (SATA / PCIe compatible)- 0 ~ 60 °C ambient operating temperature range
-
S95007B -
Keysight Technologies
Many devices do not have coaxial connectors and so they are put in fixtures in order to measure them in a coaxial environment. You must accurately remove the effects of the fixture to get a good measurement of the device under test (DUT). This option adds a powerful application wizard to guide you through characterizing a fixture and removing it from the measurement. The S95007B software is compatible with M980xA PXI Vector Network Analyzers.
-
5047 -
Abaco Systems Inc
The 5047 provides breakout of all ECM signals for debug, design validation and development. Plated through holes on the PCB allow soldering of probe wires to IO, Data, Power and Serial Identification signals. LEDs indicate presence of 3V, 5V, +12V, -12V and Ground. Elevates the ECM module by 2 mm and saves wear on the ECM carrier board connectors. Since this is a debug too there is no serial identification circuit.
-
Schwarzbeck Mess Elektronik
The Coupling- / Decoupling Networks are used to inject common mode disturbances to Equipment under Test (EuT). Further the CDNs provide sufficient decoupling between Auxiliary Equipment (AE) and disturbance signal. The requirements for CDN and their application are described in the standard IEC 61000-4-6 (Immunity to conducted disturbances, induced by radio-frequency fields). CDNs have a common mode impedance of 150 Ohm and are available for a multitude of cable types and connectors.
-
GPS221 -
INSTOCK Wireless Components, Inc
GPS221 is a two way, passive, GPS signal splitter ideal for splitting a GPS antenna signal between two receivers while providing a DC current path to power a remotely located active GPS antenna from one receiver while blocking the DC path from the other. Furnished with TNC female connectors all ports. A special feature of this unit is the 200 ohm internal load which provides a current drain for the GPS receiver not powering the active antenna. Some GPS receivers incorrectly sense an antenna fault when there is no current draw. The 200 ohm internal load provides a simulated antenna current drain which prevents receiver faulting. Max voltage rating at the DC blocked port is 15 VDC; maximum current rating is 75 mA. Max voltage rating at the DC pass port is 50 VDC; max current rating is 2000 mA.
-
GPS321 -
INSTOCK Wireless Components, Inc
GPS321 is a three way, passive, GPS signal splitter ideal for splitting a GPS antenna signal between two receivers while providing a DC current path to power a remotely located active GPS antenna from one receiver while blocking the DC path from the other. Furnished with TNC female connectors all ports. A special feature of this unit is the 200 ohm internal load which provides a current drain for the GPS receiver not powering the active antenna. Some GPS receivers incorrectly sense an antenna fault when there is no current draw. The 200 ohm internal load provides a simulated antenna current drain which prevents receiver faulting. Max voltage rating at the DC blocked ports is 15 VDC; maximum current rating is 75 mA. Max voltage rating at the DC pass port is 50 VDC; max current rating is 2000 mA.
-
GPS421 -
INSTOCK Wireless Components, Inc
GPS421 is a four way, passive, GPS signal splitter ideal for splitting a GPS antenna signal between two receivers while providing a DC current path to power a remotely located active GPS antenna from one receiver while blocking the DC path from the other. Furnished with TNC female connectors all ports. A special feature of this unit is the 200 ohm internal load which provides a current drain for the GPS receiver not powering the active antenna. Some GPS receivers incorrectly sense an antenna fault when there is no current draw. The 200 ohm internal load provides a simulated antenna current drain which prevents receiver faulting. Max voltage rating at the DC blocked ports is 15 VDC; maximum current rating is 75 mA. Max voltage rating at the DC pass port is 50 VDC; max current rating is 2000 mA.
-
MCS-04 -
OPTOKON a.s.
The OPTOKON MCS-04 offers a low cost, field usable, quick repairs of tactical cables in the toughest of environments. Utilising the proven mechanical splice in both singlemode and multimode applications, there is no need for power, heat or complicated termination procedures. Based on standard mechanical splice technology the MCS-04 provides low loss fiber jointing in just a few minutes. Cable retention and tie off is achieved through the aramid yarn and IP 67 guaranteed in the same way as military connectors. With a small diamensions the Mini Cable Splice provides a permanent join of military tactical cables up to 4 fibers. The MCS-04 is supplied as the OMK-SR-MCS kit. Purchased with all the tooling and consumables necessary to carry out the operation, the kit comes complete with splice unit, ready for use in a rugged field usable carry case. Splice unit, spares and consumables are then replaced and replenished at a low cost whenever necessary.
-
OMK-SR-MCS -
OPTOKON a.s.
The OPTOKON OMK-SR-MCS Mini cable splice tool kit offers all necessary tools and components for field usable, quick repairs of cables in the toughest of environments. Utilising the proven mechanical splice in both singlemode and multimode applications, there is no need for power, heat or complicated termination procedures. Based on standard mechanical splice technology of the MCS-04, the tool kit provides low loss fiber jointing in just a few minutes. Cable retention and tie off is achieved through the aramid yarn and IP 67 guaranteed in the same way as connectors. With a small diamensions the Mini Cable Splice provides a permanent join of ruggedized cables up to 4 fibers. Purchased with all the tooling and consumables necessary to carry out the operation, the kit comes complete with splice unit, ready for use in a rugged field usable carry case. Splice unit, spares and consumables are then replaced and replenished at a low cost whenever necessary.
-
SEN-30004-K47 -
Playing With Fusion Inc
Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino. The MAX31855K supports a measured temperature range of -270C-1372C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or Mega
