Showing results: 466 - 480 of 2906 items found.
-
Part No. CCP-38S -
Teledyne Relays
Normally Open, Low PIM, SP3T, SP4T, or SP6T, Multi-Throw switch, 50Ω impedance Available with SMA connectorsDC-3GHz
-
Part No. CCR-48K/CR-48K -
Teledyne Relays
Normally open, SP3T, SP4T, or SP6T Multi-Throw switch, 50Ω impedance Available in Commercial and Elite models, with 2.92mm connectorsDC-40GHz
-
Part No. CCP-47N -
Teledyne Relays
Normally Open, Low PIM, SP3T, SP4T, or SP6T, Multi-Throw switch, 50Ω impedance Available with N connectorsDC-3GHz
-
Part No. CCP-18N -
Teledyne Relays
Normally Open, Low PIM, SP3T, SP4T, or SP6T, Multi-Throw switch, 50Ω impedance Available with N connectorsDC-3GHz
-
510170114 -
Virginia Panel Corporation
Mates with p/n 510171114.Please note: The RJ45 connectors extend beyond the width of the module. Care should be taken when installing in positions adjacent to other PCBs. Please contact VPC, if further assistance is needed.
-
510171114 -
Virginia Panel Corporation
Mates with p/n 510170114.Please note: The RJ45 connectors extend beyond the width of the module. Care should be taken when installing in positions adjacent to other PCBs. Please contact VPC, if further assistance is needed.
-
YOKOWO Co., Ltd.
Yokowo Connector Test Tools - BtoB Clips, Interface Connectors, and Tools for FPC Connectors
-
RAMSEY Electronics,Inc
Interface / Power / Cooling / Accessory Options - rf feed through connectors, fiber bulkheads, usb interfaces-rf data connectors, ethernet interfaces-rf data connectors, video interfaces, data interfaces, rf filtered power interfaces, and more.
-
JT 2111/MPV DIOS IDC -
JTAG Technologies Inc.
The JT 2111/MPV is a 64 channel boundary-scan digital I/O scan module enclosed in an impact resistant housing. The module is designed to test and control edge connectors, on-board connectors and logic clusters in boundary-scan applications. Multiple modules can be connected serially to increase the number of I/Os. Available with 96-pin DIN 41612 connectors and 20-pin 0.1″ pitch IDC connectors.
-
AS1/2 -
VECTOR Electronics and Technology, Inc.
Fits onto rear face of rear extrusion rails to mountDIN 41612 type connectors directly in subrack.HP pitch pattern of holes for precise installation of connectors.
-
540273010055 -
Virginia Panel Corporation
2 PCB Adapters, Receiver, QuadraPaddle, two 192 Position, to 2 PCB-Mounted Female VHDCI Connectors (510150126) and 2 PCB-Mounted InfiniBand Connectors (510150210)
-
MCT 192 -
REINHARDT System- und Messelectronic GmbH
MCT 192 is an easy-to-use high-speed cable tester for testing multi-wire cables and complete backplanes. The multi-contact board is equipped with contacting sockets and connectors common in industries. Fixturing is therefore unnecessary. In case you use connectors which are not supplied with the multi-contact board, you can mount and wire these connectors on a raster plug-in board.
-
DORC's ZX-1 -
Direct Optical Research Company
Used primarily to measure multi fiber (MT/MPO and MT-RJ) connectors, DORC's fourth generation "ZX-1 mini Array+" is the result of 18 years of hardware and software product development. Although optimized for mutifiber connectors, the ZX-1 mini Array plus also does an excellent job of measuring single fiber PC and APC connectors. DORC's patented design is based on a variant of the Michelson configuration, and provides BOTH 2D and 3D high resolution images of the sample under test in approximately 45 seconds for multi fiber connectors and just 3-4 seconds for single fiber connectors - from the time the connector is inserted.
-
N4432D -
Keysight Technologies
The Keysight N4432D is a precision 4-port ECal module that supports selection of Type-N and 3.5 mm connectors mixed up to 18 GHz. Select either female-female, male-male, or female-male connectors.
-
SparkFun Electronics
RJ45 connectors are the kind that are used for Ethernet jacks, but they make great general purpose connectors when you need a lot of conductors. This is a small PCB that brings out the pins of the RJ45 connector to an in-line 0.1" footprint. Use with break-away headers for breadboarding or create your own RJ45 cable. Check the related items for Ethernet cable and connectors to go with it!