Showing results: 31 - 45 of 1754 items found.
-
-
VLT3673-G6 -
Van Leeuwen Test Systems BV
The VLT 3673-G6 suspension / road contact testers operate according to the well-known EUSAMA principle. However, the diagnostic options are not restricted to the contents of this specification. In addition to the usual road contact values, the following values are also measured and displayed: the contact value difference, resonance frequency and wheel weight at minimum contact value, tyre rigidity, wheel weight and axle weight. There is a general final evaluation so that all these values do not have to be interpreted after every test.
-
Omega Engineering, Inc
Contact level devices come in contact with the tank media and are used for point or cocntinious level measurement. Types include Float, Optical, RF Capacitence, Conductivity, Ultrasonic, Tuning Fork.
-
JYL-200B/100B -
Kingrun Instrument Co., Ltd.
Product description: JYL-200B/100B contact resistance tester can measure contact resistance of high voltage switches and circuit breakeres, also can test primar side resistance of transformer and grounding wire in groups
-
WIKA Alexander Wiegand SE & Co. KG
Wherever the process temperature has to be indicated locally and, at the same time, limit values must be monitored, thermometers with switch contacts find their application. The switch contacts make or break the circuit dependent upon the pointer position of the indicating measuring instrument. If the reading is significantly above or below a set value, they trigger an alarm, hence also the term “alarm contact”. The instruments are also suitable for starting, stopping or switching processes.
-
The Motwane Manufacturing Company
High contact resistance values are a definite cause of the failure or less than optimal performance in a wide variety of electrical devices. Contact resistance testing is therefore most critical to measure the resistance of electrical connections in switching devices, circuit breakers, isolators, busbars, relays, joints, connectors, cables, and cable joints. The device helps to find destructive or corroded contacts and hence protects substation devices from damage.
-
CTX -
E-Max Instruments
The CTX relays supply a 1.5 to 2.5 seconds of a contact output time extension for a momentary contact input. The CTX allows slower device such as scada systems and annunciators to operate thus preventing data loss on the action of protective relays/devices or trip indicators such as the E-Max Trip indication Relay (TIR).
-
SDT Ultrasound Solutions
Inspect bearings, steam traps and perform other mechanical inspections with our Needle or Threaded contact sensors.
-
UWE Electronics
We differentiated the spring contact probes by center and application, for the purpose of clarity. Please choose in the left navigation bar!
-
DT141 -
Fourier Systems
This MicroLog sensor monitors Reed Relay contacts and switch status (open/closed), to identify the correlation between phenomena such as temperature change and door status.
-
Micro Power -
Virginia Panel Corporation
Rated to 10,000 cycles.Rated to 21 Amps cont w/ 12 AWG wire.Max contact resistance of 1.5 mOhms.Mating force of 2 lbs.
-
JYK II -
Kingrun Instrument Co., Ltd.
•Instrument IPC architecture for domestic production of all models of metal contacts SF6 switchgear, GIS combination of electrical, vacuum switch, oil switch and column switches, contacts and so on.•Sensor: Acceleration speed sensor, rotation speed sensor, linear stroke sensorinstallation is very easy and simple.•Trigger: The trigger, external trigger, the sensor is triggered. Sensor can trigger the circuit breaker manually switching characteristic test, such as a manual column pole division switch.
-
Amphenol Fiber Systems International
Physical Contact (PC) connections are characterized by the physical mating of two optical fibers. Precision ceramic ferrules are typically utilized for PC connections. A PC connection is accomplished by terminating the optical fiber into a precision ceramic ferrule. Epoxy is used to affix the fiber into the ferrule. The tip of the ceramic ferrule is polished in a precise manner to ensure that light enters and exits at a known trajectory with little scattering or optical loss. Polishing the terminated ceramic ferrule is a critical process in Physical Contact fiber optic connectors.
-
PeakTech Prüf- und Messtechnik GmbH
Provides a fast and accurate measurement of the speed and surface speed of rotating objects. Through the contactless or with the measuring adapter for measurements by direct contact to the object to be measured, various speeds can be determined and recorded.
-
Virginia Panel Corporation
VPC offers a range of pneumatic connectors that are ideal for use with automatic engagement interface systems. These pneumatic contacts also work well when used together with the VPC iDock Series.