Showing results: 1126 - 1140 of 2536 items found.
-
778572-10 -
NI
68-Channel, 2 A PXI Signal Insertion Switch Module—The PXI‑2510 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2510 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
-
HPx-300 -
Cambridge Pixel Ltd.
The HPx-300 Radar Signal Output card generates representative radar signals for system testing, simulation, training or radar video streaming. Under software control, the card generates radar video, trigger and azimuth signals similar to those generated by real radars. This permits radar display or processing systems to be tested and qualified using laboratory-based equipment before installation with the radar.
-
Doble Engineering
Doble offers a comprehensive line of diagnostic equipment and software solutions for the verification of system protection. Our solutions allow you to challenge any protection and control circuit and simulate system condition. Our software is flexible and our equipment is modular allowing you to customize your testing program, adhere to your company's practices and procedures, while meeting regulatory requirements.
-
WaveRunner 8000HD 8 -
Teledyne LeCroy
Today's highly complex power-conversion systems, automotive ECUs and embedded control systems are becoming smaller, denser and faster, with more signals, sensor inputs and lower-voltage power rails than ever. WaveRunner 8000HD’s combination of 12-bit resolution at 2 GHz bandwidth, 8 (or more) channels, very long capture times, and a complete software toolset makes it ideal for these key applications.
-
CIS300 -
Stanford Research Systems, Inc.
With better than 1 ppm detection limit, direct sampling at mTorr pressure, and a user-friendly Windows software package, the CIS systems will satisfy your most demanding applications. On-line process monitoring and control, verification of process gas purity at the point of use, high-vacuum residual gas analysis, and process equipment leak checking are some of the areas where these systems will prove indispensable
-
CIS200 -
Stanford Research Systems, Inc.
With better than 1 ppm detection limit, direct sampling at mTorr pressure, and a user-friendly Windows software package, the CIS systems will satisfy your most demanding applications. On-line process monitoring and control, verification of process gas purity at the point of use, high-vacuum residual gas analysis, and process equipment leak checking are some of the areas where these systems will prove indispensable
-
CIS100 -
Stanford Research Systems, Inc.
With better than 1 ppm detection limit, direct sampling at mTorr pressure, and a user-friendly Windows software package, the CIS systems will satisfy your most demanding applications. On-line process monitoring and control, verification of process gas purity at the point of use, high-vacuum residual gas analysis, and process equipment leak checking are some of the areas where these systems will prove indispensable
-
GL Communications Inc.
GL’s T1 E1/Analog Test Suite supports analysis and emulation of legacy protocols (MFCR2, E&M, SS1/SS4, SS5, Voice Call Signaling, 2-wire Call, SF Signaling (DTMF)) applicable to Federal Aviation Administration "FAA" within their National Airspace System "NAS" Ground-to-Ground Air Traffic Control Network and Voice System (NVS) to Analog Interphone.
-
Shimadzu Corp.
The Shimadzu simulated distillation system, consisting of a Nexis GC-2030 high-performance capillary gas chromatograph and LabSolutions simulated distillation GC analysis software, meets all applicable ASTM, ISO, EN, and JIS standards. Permitting accurate and highly reproducible analysis of high-boiling components in crude oil samples, it is the optimal system for product quality control and process management in oil refinery plants.
-
Seismic Source Co.
*GPS accuracy for time break collection and source equipment locations.*32-bit, high speed, ADC chip for lower noise and increased accuracy for signatures.*Operates independently of crew, including observer and shooter or operators.*Can be used with any Vibrator Control System.*Great for monitoring rental equipment and operators.*Provides accurate start times that can be used with any nodal recording system.
-
Insitec Range -
Malvern Panalytical Ltd
Insitec systems deliver the online continuous particle size analysis needed for efficient, cost-effective monitoring and control of industrial processes. Suitable for the widest variety of process streams from dry powders to hot sticky slurries, sprays and emulsions, whether milligrams of material or hundreds of tonnes per hour. Insitec systems measure particles in the size range 0.1 micron to 2.5 mm.
-
M+P International
Vibration tests must be safe and reliable and this is especially true for high value specimens in critical aerospace testing applications. Here, m+p Coda offers maximum safety: The monitoring system captures and records data such as acceleration, temperature and strain continuously during vibration tests - irrespective of the vibration control system in use. Each channel can be configured separately for total flexibility.
-
95006 -
HITEC Sensor Solutions Inc.
A patented, precision, solid state motion sensor consisting of a sensing head (encoder) and a master control panel and enclosure, the Mark II features a digital tachometer and a two-set point system. Use of a dual set point system, properly set, assures warning of a potential problem, allowing corrective action before damage can occur, and providing total shutdown if the problem is not corrected.
-
BA500 Series -
Battery Metric
The BA500 analyzers are high performance battery analyzers with charge and discharge capabilities. The analyzers connect to your computer via USB and the BA500WIN software program is used to control the analyzer and battery under test. This system has a fast data collection system allowing you to collect and view as much data as required. Once you collect this data you can graph, analyze & save it.
-
Circutor, sa
Solutions for monitoring and recording any value you wish to manage (electricity, water, gas consumption, temperatures, flow rates, pressures, units produced, etc.), either through communications or through pulse logger systems. The control system family contains the LINE solution to create a comprehensive energy management systems (SGEi), LM pulse loggers and MDC controllers to avoid surcharges in the electric bill by preventing the contracted capacity in electrical installations from being exceeded.