Showing results: 646 - 660 of 6936 items found.
-
Bias-T PLUS -
Array Solutions
The Array Solutions Bias-T PLUS is a 1.8-148 MHz stand alone weatherproof unit that permits the application of DC control signals of up to 400ma on your coax cable. By inserting the control voltage on the coax cable feed-line, you eliminate the requirement for external DC wires for powering remote devices.The Bias-T PLUS weatherproof assembly means that it can be placed indoors or outdoors for maximum flexibility. Typically, one Bias-T PLUS will be placed indoors for inserting DC on your coax feed-line, and one Bias-T PLUS will be placed at the remote device where the DC voltage is extracted.
-
MX Series -
Aim-TTi
Three or four high performance outputs each with full functionalityRange switching gives variable voltage/current combinationsShared power mode provides double power from a single outputLow output noise and ripple via linear final regulationHigh setting resolution of up to 1mV and 0.1mAVariable OVP and OCP trips on all outputs50 setting memories per output plus 50 linked memoriesSelectable voltage tracking (isolated tracking)Selectable current meter averagingSwitchable remote sense capabilityGraphic LCD provides simultaneous output meteringNumeric or spin-wheel control of all parametersIndividual or combined output on/off control with programmable delay sequencing.3U half-rack case for bench or rack mounting (4U rack kit accessory available)RS-232, USB and LAN (LXI) interfaces (P models)GPIB option (P models only)Duplicate power & sense terminals at rear (P models)
-
EX-R Series -
Aim-TTi
Single outputs, 35V/5A, 18V/10A, 42V/10A, 20V/20ADual or triple outputs, 35V/4AIndependent digital voltage and current meters for each output with 4 digit resolutionSwitchable local or remote sensingConstant voltage or constant current operationVariable 1.5 - 5.0V auxiliary output at 5A (EX354RT)Compact design uses less bench spaceSilent fan-free cooling (not EX202R/EX4210R)DC output switches, automatic mode indicationRS232 or USB controlled models available (35V/5A single)Multi-mode dual model 2x(75V/2A) or 75V/4A or 150V/2A
-
780935-01 -
NI
The PCIe‑GPIB+ combines an IEEE 488 controller and an analyzer on one device for computers with PCIe slots. You can use this device to integrate an instrument into your system using GPIB as well as to troubleshoot and solve GPIB hardware and software problems. The PCIe‑GPIB+ achieves maximum IEEE 488.2 transfer rates. With an onboard bus master DMA controller, there is no microprocessor interruption in data transfers. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Talos-2000 Series -
ADLINK Technology Inc.
ADLINK's Talos-2000 Series ready-to-use automation control system, powered by 6th Generation IntelR Core? i7/i5/i3 processors, provides EtherCAT control and four independent PoE (power over Ethernet) ports, with data transfer rates up to 4.0Gb/s. The Talos-2000 Series offers motion control of up to 64 axes, 10,000 I/O points, and 4CH PoE camera connectivity with minimal footprint. The ideal solution for machinery automation, Talos-2110 integrates complete APIs for multi-dimensional, highly synchronized and time-deterministic event-triggered motion & I/O control, high precision image capture, and data transmission. Field device connectivity in the Talos-2000 Series is provided through RJ45 connection for easy installation, and the latest 6th Generation IntelR Core? i7/i5/i3 processors enable powerful and flexible EtherCAT slave control, broad PoE camera compatibility, and compact size.
-
EL-R Series -
Aim-TTi
Single outputs, 30V/1A, 18V/3.3A, 56V/1.1A, 15V/5A, 30V/3ASingle, dual or triple outputs, 30V/2AIndependent digital voltage and current meters for each output with 4 digit resolutionSwitchable local or remote sensingConstant voltage or constant current operationVariable 1.5 - 5.0V auxiliary output at 2A (EL302RT)Compact design uses less bench spaceSilent fan-free coolingDC output switches, automatic mode indicationRS232 or USB controlled models available (30V/2A single)
-
780936-01 -
NI
The PCIe‑GPIB+ combines an IEEE 488 controller and an analyzer on one device for computers with PCIe slots. You can use this device to integrate an instrument into your system using GPIB as well as to troubleshoot and solve GPIB hardware and software problems. The PCIe‑GPIB+ achieves maximum IEEE 488.2 transfer rates. With an onboard bus master DMA controller, there is no microprocessor interruption in data transfers. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
QL Series II -
Aim-TTi
Advanced dc power supplies, single or triple outputUp to 112 watts per outputVery high precision, very low noise, excellent dynamicsAdvanced user interface with numeric and rotary controlMultiple voltage/current ranges for increased flexibilityMultiple non-volatile memories for power supply set-upsSwitchable remote sense provides perfect load regulationComprehensive protection including OVP and OCP tripsCompact bench footprint; modular width for rack mountingAuxiliary output fully variable 1.00V to 6.00V at 3A with selectable voltage and current metering (T models)Bus programmable via USB, RS232, GPIB or LAN (P models)LAN interface is LXI compliantDuplicate power and sense terminals at rear (P models)
-
PL Series -
Aim-TTi
ingle, dual or triple output modelsModels from 6V/8A up to 60V/1.5ALinear regulation - for the best performanceUltra-compact design - uses up less spaceTrue Analogue controls - for ease of useS-Lock function - instantly lock settingsV-Span function - customize the voltage rangeLow current range and current meter averagingDC output switches and "view limits" buttonSelectable remote sense terminalsIndependent, Isolated Tracking, Ratio Tracking and True Parallel modes on dual & triple modelsHigh current low voltage output on triple output model
-
CXAR/256-MF -
Cytec Corp.
This Chassis is intended to control up to eight 16x1 solid state 75 ohm cable TV modules, or may be used to control a great number of 8x1, 4x1, 2x1 or 2x2 modules. It is often used to control a large variety of custom configurations which may be located in separate chassis. When used as a separate driver chassis it can control up to 256 switch points from a 2 RU chassis. LEDs on the front panel show switch and power status. Add Switch Modules, CP16 Driver Modules and a Control Module to complete the system. Keypad Manual manual control with LCD display is optional.
-
CXM/32-MF -
Cytec Corp.
These Chassis controls up to 4 8x1 modules, 8 4x1 modules or mixtures of 8x1"s, 4x1"s, 2x1"s and 2x2 modules in any combination or configuration for up to 32 relay drives. LEDs on the front panel show switch and power status. Add Switch Modules and a Control Module to complete the system or simply buy the chassis wired out to D connectors to control your own relays. A pushbutton manual control is optional.
-
CXM/128-MF -
Cytec Corp.
These Chassis controls up to 16 8x1 modules, 32 4x1 modules or mixtures of 8x1"s, 4x1"s, 2x1"s and 2x2 modules in any combination or configuration for up to 128 relay drives. LEDs on the front panel show switch and power status. Add Switch Modules, display / driver modules and a Control Module to complete the system or simply buy the chassis wired out to D connectors to control your own relays. A manual control is optional. Chassis is available with sink or source relay drivers from + 5 to + 28 volts, ot TTL drivers for programmable attenuators. Firmware commands for Fade and Handover for WiFi, Cell Phone and WiMax labs. Fully custom systems built with little to no NRE.
-
JX/256-MF -
Cytec Corp.
These Chassis control up to 16 modules with as many as 32 two pole relays per module allowing 1xN multiplexers up to 1020x1, 2 pole muxes up to 512x1 or 2xN matrix configurations up to 256x2. Jumpering option allow the modules to be controlled as separate smaller muxes, i.e. 64 4x1 2 pole muxes, or combine specific groups to allow an almost unlimited combination of sizes. Add a Control Module and optional manual control to complete the system.
-
ADLINK Technology Inc.
ADLINK Bus expansion is a technology that increases the number of slots of the same or different bus type for a host computer system. ADLINK bus expansion product provides variety of interface options, including PCI, PCI Express, PXI, and ExpressCard to increase bus slots and leverage the latest computing power of both desktop and server-grade computers for a variety of applications. The interoperability of different bus interface devices, such PCI, PXI and PCI Express, is also a great benefit for those facing complicated system integration tasks. ADLINK bus expansion products also provide complete hardware and software transparency, without the need for additional drivers or software.
-
TDAS Control -
DTS, Inc.
TDAS Control is the original set-up, control, viewing and export software developed by DTS. TDAS Control provides easy-to-use tools for configuring output timing, as well as advanced features such as automatic sensor assignment, detailed channel diagnostics, real-time display and squib fire for airbag testing. TDAS Control only works with TDAS G5 and TDAS PRO.