Showing results: 976 - 990 of 6937 items found.
-
A1F -
Dwyer Instruments Inc.
Low Cost and Precision Made. The A1 Pressure Control provides the flexibility required for industrial applications. The A1 pressure switch is ideal for panel mounting wherever a high quality economical open case control is required. Optional weatherproof housing meets NEMA 4X standards
-
W-IE-NE-R, Plein & Baus GmbH
CAMAC - "Computer Aided Measurement And Control" is a joint specification of the U.S. NIM and the European ESONE committees. CAMAC was introduced in 1969 by ESONE and fully defined in 1971 with the standards EUR4100 and EUR4600. It represents a complementation of the NIM standard for computer based experiment control and data acquisition / measurements.
-
Avantes Inc.
Any Avantes AvaSpec spectrometer can operate in stand-alone mode in which the spectrometer is not connected to a computer. The stand-alone mode is developed for process control applications, in which the spectrometer must output analog or digital signals that can be directly coupled to Programmable Logical Controllers (PLC) in a process control environment.
-
QI-DL-2100 -
Quaesta Instruments
The QI-DL-2100 data logger has multiple inputs and outputs for use in a wide range of logging and control applications. The device is configured through simple commands that make it fast and easy to use. Optional Integrated cellular or Iridium modem allow data downloading and remote control.
-
RF Industries
Remote Electrical Tilt (RET) systems are being installed in many wireless infrastructure sites to optimize signal patterns. The RET control cable between the control unit and the antenna is the least appreciated system component, unless you cannot get one to complete your installation.
-
BTT Series -
Jinan Testing Equipment IE Corporation
The biaxial tensile testing machine consists of two parts, mechanical system and control system; mechanical system includes load frame, membrane specimen fixtures, servo motors(Japan), load sensors, displacement sensor and other components, while control system with the computer and software;
-
North Atlantic Industries
Vehicle Management Systems (VMS) are used to perform a multitude of functions on critical military platforms including manned and unmanned military aircraft, helicopters, shipboard vessels, autonomous missile systems and military ground vehicles, and function as the core control element within a redundant control system.
-
MKS Instruments
The 1150C Vapor Source Mass Flow Controllers are pressure based measurement and control systems designed to meter and control vapor from low vapor pressure liquid and solid sources directly, without the need of a carrier gas using viscous flow through a choked orifice.
-
HXV/32-MF -
Cytec Corp.
These Chassis controls up to 4 8x1 modules, 4 4x2 modules, or up to 2 of the 8K modules in almost any combination or configuration. LEDs on the front panel show switch and power status. Add Switch Modules, Driver Modules and a Control Module to complete the system.
-
HXV/128-MF -
Cytec Corp.
These Chassis controls up to 16 8x1 modules, 16 4x2 modules, or up to 8 of the 8K modules in almost any combination or configuration. LEDs on the front panel show switch and power status. Add Switch Modules, Driver Modules and a Control Module to complete the system.
-
HXV/96-MF -
Cytec Corp.
These Chassis controls up to 12 8x1 modules, 12 4x2 modules, or up to 6 of the 8K modules in almost any combination or configuration. LEDs on the front panel show switch and power status. Add Switch Modules, Driver Modules and a Control Module to complete the system.
-
MC108-2 -
Systems Engineering & Management
The MC100 Series Multi-Coupler is a 1U Rack-Mount device that provides RF distribution form 200 MHz to 5250 MHz. Both single and dual output configurations are available, as well as up to 8 output channels. Each output is an independent channel with +/- 5 dB gain controls, providing the ability to balance all outputs within +/- 1 dBm. Frequency Channel selection is from both front panel controls as well as remote control via Ethernet and SEMCO's MCCS Network software program.
-
Series G -
Teledyne Defense Electronics Relays & Coax Switch
Series G relays are designed for medium-power loads. The design incorporates a thyristor output. Series G relays utilize optical isolation to protect the control from load transients. An internal MOV is also provided to protect against load transient voltages. The compact size makes it ideal for designs where space is limited. Zero-Cross and Random switching options available.Available options include:G24R12-06 12Arms, 12-320Vrms, 520Vpeak Load; 3-32Vdc Control; RandomG24D12-06 12Arms, 12-320Vrms, 520Vpeak Load; 3-32Vdc Control; Zero-Cross
-
MXIe -
Terotest Systems Ltd.
The MXIe PXI-Express Bus Expanders allows for direct control of PXI-Express systems from any PCI Express slot in a desktop computer or server. MXIe-Express configurations are available for supporting both the x1 and x4 PCI-Express lane configurations. Either lane configuration can remotely control one or two PXIExpress chassis. The MXIe-Express technology utilizes a high bandwidth link that is transparent to software applications and drivers, providing the ability to use high performance desktop computers or servers to control PXI-Express systems.
-
MXIe-Express Series -
Marvin Test Solutions, Inc.
The MXIe PXI-Express Bus Expander allows for direct control of PXI-Express systems from any PCI Express slot in a desktop computer or server. MXIe-Express configurations are available for supporting both the x1 and x4 PCI-Express lane configurations. Either lane configuration can remotely control one or two PXIExpress chassis. The MXIe-Express technology utilizes a high bandwidth link that is transparent to software applications and drivers, providing the ability to use high performance desktop computers or servers to control PXI-Express systems.