Showing results: 2086 - 2100 of 2272 items found.
-
Model 3560 -
Jinan Testing Equipment IE Corporation
This extensometer is ideally suited for testing anisotropic materials such as advanced composites as well as for general purpose tests like determining Poisson’s ratio. The Model 3560BIA uses a design unique to Epsilon, where the knife edges remain parallel during the displacement. This approach greatly reduces crosstalk between axes and allows use on round or flat specimens with equal ease. These extensometers are very easy to mount. Integral springs hold the unit on the test sample. The parallel multiple flexure design makes these units very durable.The Model 3560AVG reads axial strain only as a single averaged output. It may also be supplied with two independent outputs, one measurement from each side of the specimen. This set-up is most commonly required when an indication of specimen bending is desired. The second version, the Model 3560BIA, includes both the averaged axial strain and the transverse strain. Again, this may also be configured as dual independent axial readings, which results in a three channel extensometer.The Model 3560 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Falcon Electric, Inc
*UPS Monitoring. Falcon’s Dry Contact Relay Card facilitates UPS status via configurable relay contact activation for simple integration into existing PLC/ monitoring systems.*Flexible Configuration. Easily installs into all SSG and SSG-RP UPS models. Configurable to allow simple selection of active open or closed relay contacts.*Notification & Remote Shutdown Capability. Provides relay contact activation during a UPS event including utility power loss, low battery, UPS fault and bypass condition. Supports safe shutdown of the UPS after a utility power loss event.*Simple Integration. The detachable connection facilitates simple integration into existing programmable logic controller (PLC) or management systems.
-
CEM842 -
Axiomtek Co., Ltd.
The CEM842 Intel® Bay Trail SoC system-on-module comes with 6 PCI Express lanes, eight USB signals, double deck DDR3L SO-DIMM sockets supporting up to 8 GB of system memory, and two SATA-300. The CEM842 palm size module is based on the ultra-low power Intel® Celeron® processor J1900 or N2807 with Intel® HD Graphics engine, delivering outstanding computing, graphical and media performance. The compact computer on module is designed with all necessary components and offers the most updated bus interfaces targeting at POS and kiosk systems, gaming, medical PCs, human machine interface, IoT & M2M-related and industrial automation controllers.
-
700HPPK -
Fluke Calibration
The Fluke Calibration 700HPPK Pneumatic Test Pump Kit generates and adjusts pneumatic pressures up to 21 MPa (3000 psi), without requiring a nitrogen bottle or other external pressure supply. It supplies pressure to devices under test (DUTs) that include transmitters, controllers, pilots, digital and analog gauges, and more. It’s the perfect solution for generating high pressure in the field, where conditions and operating surfaces can vary. The 700HPPK is the ideal choice for calibration technicians, test engineers, and instrument technicians working in industries like natural gas transmission and distribution, process, aerospace and defense, who need a simple-to-use, safe and portable pressure source that they can depend on in a wide variety of conditions.
-
Instron
These three zone resistance wire wound furnaces are of split construction to facilitate fast and easy loading of a pre-assembled specimen train. The case is constructed from stainless steel with aluminium and hardened insulation board end plates. The optional front cut-out allows the use of side-entry high-temperature extensometry. Adjustable stainless steel latches keep the furnace halves locked together during use, but are then easily opened once testing is complete. The furnace is available with optional heavy duty brackets or mountings, which attach to a wide range of testing systems. An extensive range of standard controllers is available to suit most test regimes. Custom variants can be specified should the standard range not include a suitable unit.
-
Analog Devices Inc.
ADI’s portfolio of embedded Real Time Ethernet Switch are ideal solution for adding Industrial Ethernet connectivity to any field device or controller application. Designed for scalable and flexible system development, they support all major Industrial Ethernet Protocols while also providing the ability to future-proof for many Time Sensitive Networking (TSN) features, for the IEC/IEEE 60802 industrial profile. They interface easily with any host processor including any ARM® CPU utilizing the protocol specific device drivers provided by ADI. This provides the flexible system partitioning enabling the selection of processor that best fits your application requirements. It also provides the freedom to utilize any vendors protocol stack.
-
WEW-D Series -
Jinan Testing Equipment IE Corporation
WEW-D series hydraulic manual UTM is suitable for testing tension, compression and other strengths of various metallic or nonmetallic materials with high strength. The hydraulic manual UTM is capable of testing the characters of materials on physical & technology properties. As a manual control & economical UTM, the hydraulic manual UTM is with reasonable and reliable configurations (load cell or pressure transducer, extensometer, photoelectric encoder, servo motor & driver, standard screws), which can satisfy ordinary testing requirements. Digital controller and computer with software can be equipped on this machine to realize the test date/curve collecting and process. The hydraulic UTM of economical type is easy to operate and is versatile in the applications of metallurgy manufacturers such as steel mills & alloy, reinforced bar etc.
-
SCR ELEKTRONIKS
SCR ELEKTRONIKS introduces Safety Test Panel for Domestic Mixer with PC Datalogging. The tests are Performed as Prescribed in IS the Panel Carries out different tests one by one and provides indication of the Test results as OK or NOT-OK. It is very useful and handy in line testing on Mass production line as well as type Testing. Special fixture can be provided for the specific product. This avoids the connections & disconnections of the product for different tests. The total time for entire testing is less than 20 seconds. Micro controller based sequential timer maintains the sequence of operation and displays the test status. This manual contains information about operating instructions and maintenance of the equipment. Please go through this manual carefully and retain it for future reference.
-
785151-01 -
NI
The ISC‑1782 is a high-performance smart camera for machine vision and is powered by a 1.58 GHz dual-core Intel Celeron processor. The combination of the onboard processor with a CMOS image sensor provides an easily distributed all-in-one system. In addition to high-performance image acquisition and processing, you can use built-in digital I/O and industrial communication options for dynamic, real-time communication and integration with industrial automation devices including programmable logic controllers (PLCs), human machine interfaces (HMIs), robotics, sensors, and industrial machinery. You can configure NI Smart Cameras with the included Vision Builder for Automated Inspection (AI) software or program the camera with the LabVIEW Real‑Time Module and the Vision Development Module.
-
785150-01 -
NI
The ISC‑1782 is a high-performance smart camera for machine vision and is powered by a 1.58 GHz dual-core Intel Celeron processor. The combination of the onboard processor with a CMOS image sensor provides an easily distributed all-in-one system. In addition to high-performance image acquisition and processing, you can use built-in digital I/O and industrial communication options for dynamic, real-time communication and integration with industrial automation devices including programmable logic controllers (PLCs), human machine interfaces (HMIs), robotics, sensors, and industrial machinery. You can configure NI Smart Cameras with the included Vision Builder for Automated Inspection (AI) software or program the camera with the LabVIEW Real‑Time Module and the Vision Development Module.
-
785149-01 -
NI
The ISC‑1782 is a high-performance smart camera for machine vision and is powered by a 1.58 GHz dual-core Intel Celeron processor. The combination of the onboard processor with a CMOS image sensor provides an easily distributed all-in-one system. In addition to high-performance image acquisition and processing, you can use built-in digital I/O and industrial communication options for dynamic, real-time communication and integration with industrial automation devices including programmable logic controllers (PLCs), human machine interfaces (HMIs), robotics, sensors, and industrial machinery. You can configure NI Smart Cameras with the included Vision Builder for Automated Inspection (AI) software or program the camera with the LabVIEW Real‑Time Module and the Vision Development Module.
-
785148-01 -
NI
The ISC‑1782 is a high-performance smart camera for machine vision and is powered by a 1.58 GHz dual-core Intel Celeron processor. The combination of the onboard processor with a CMOS image sensor provides an easily distributed all-in-one system. In addition to high-performance image acquisition and processing, you can use built-in digital I/O and industrial communication options for dynamic, real-time communication and integration with industrial automation devices including programmable logic controllers (PLCs), human machine interfaces (HMIs), robotics, sensors, and industrial machinery. You can configure NI Smart Cameras with the included Vision Builder for Automated Inspection (AI) software or program the camera with the LabVIEW Real‑Time Module and the Vision Development Module.
-
778998-01 -
NI
13-Bit, 32-Channel, 800 kS/s PXI Analog Output Module—The PXI‑6723 delivers low-cost, high-density analog outputs to meet a wide range of applications, such as stimulus-response, signal simulation, waveform generation, and actuator stimulation. In addition, the device provides eight 5 V TTL/CMOS digital I/O lines; two 24‑bit, 20 MHz counter/timers; and digital triggering and external clocking capabilities. The PXI‑6723 can replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators. You can control each data point for each channel to define common waveforms, such as square, sine, or sawtooth, as well as complex waveforms.
-
785155-01 -
NI
The ISC‑1783 is a high-performance smart camera for machine vision and is powered by a 1.58 GHz dual-core Intel Celeron processor. The combination of the onboard processor with a CMOS image sensor provides an easily distributed all-in-one system. In addition to high-performance image acquisition and processing, you can use built-in digital I/O and industrial communication options for dynamic, real-time communication and integration with industrial automation devices including programmable logic controllers (PLCs), human machine interfaces (HMIs), robotics, sensors, and industrial machinery. You can configure NI Smart Cameras with the included Vision Builder for Automated Inspection (AI) software or program the camera with the LabVIEW Real‑Time Module and the Vision Development Module.
-
785154-01 -
NI
The ISC‑1783 is a high-performance smart camera for machine vision and is powered by a 1.58 GHz dual-core Intel Celeron processor. The combination of the onboard processor with a CMOS image sensor provides an easily distributed all-in-one system. In addition to high-performance image acquisition and processing, you can use built-in digital I/O and industrial communication options for dynamic, real-time communication and integration with industrial automation devices including programmable logic controllers (PLCs), human machine interfaces (HMIs), robotics, sensors, and industrial machinery. You can configure NI Smart Cameras with the included Vision Builder for Automated Inspection (AI) software or program the camera with the LabVIEW Real‑Time Module and the Vision Development Module.
