Showing results: 2101 - 2115 of 2272 items found.
-
785153-01 -
NI
The ISC‑1783 is a high-performance smart camera for machine vision and is powered by a 1.58 GHz dual-core Intel Celeron processor. The combination of the onboard processor with a CMOS image sensor provides an easily distributed all-in-one system. In addition to high-performance image acquisition and processing, you can use built-in digital I/O and industrial communication options for dynamic, real-time communication and integration with industrial automation devices including programmable logic controllers (PLCs), human machine interfaces (HMIs), robotics, sensors, and industrial machinery. You can configure NI Smart Cameras with the included Vision Builder for Automated Inspection (AI) software or program the camera with the LabVIEW Real‑Time Module and the Vision Development Module.
-
785146-01 -
NI
The ISC‑1781 is a high-performance smart camera for machine vision and is powered by a 1.58 GHz dual-core Intel Celeron processor. The combination of the onboard processor with a CMOS image sensor provides an easily distributed all‑in‑one system. In addition to high-performance image acquisition and processing, you can use built-in digital I/O and industrial communication options for dynamic, real-time communication and integration with industrial automation devices including programmable logic controllers (PLCs), human machine interfaces (HMIs), robotics, sensors, and industrial machinery. You can configure NI Smart Cameras with the included Vision Builder for Automated Inspection (AI) software or program the camera with the LabVIEW Real‑Time Module and the Vision Development Module.
-
786306-01 -
NI
The USB-8501 is a low-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8501 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8501 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
786307-01 -
NI
The USB-8501 is a low-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8501 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8501 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
785149-01 -
NI
The ISC‑1782 is a high-performance smart camera for machine vision and is powered by a 1.58 GHz dual-core Intel Celeron processor. The combination of the onboard processor with a CMOS image sensor provides an easily distributed all-in-one system. In addition to high-performance image acquisition and processing, you can use built-in digital I/O and industrial communication options for dynamic, real-time communication and integration with industrial automation devices including programmable logic controllers (PLCs), human machine interfaces (HMIs), robotics, sensors, and industrial machinery. You can configure NI Smart Cameras with the included Vision Builder for Automated Inspection (AI) software or program the camera with the LabVIEW Real‑Time Module and the Vision Development Module.
-
785148-01 -
NI
The ISC‑1782 is a high-performance smart camera for machine vision and is powered by a 1.58 GHz dual-core Intel Celeron processor. The combination of the onboard processor with a CMOS image sensor provides an easily distributed all-in-one system. In addition to high-performance image acquisition and processing, you can use built-in digital I/O and industrial communication options for dynamic, real-time communication and integration with industrial automation devices including programmable logic controllers (PLCs), human machine interfaces (HMIs), robotics, sensors, and industrial machinery. You can configure NI Smart Cameras with the included Vision Builder for Automated Inspection (AI) software or program the camera with the LabVIEW Real‑Time Module and the Vision Development Module.
-
785150-01 -
NI
The ISC‑1782 is a high-performance smart camera for machine vision and is powered by a 1.58 GHz dual-core Intel Celeron processor. The combination of the onboard processor with a CMOS image sensor provides an easily distributed all-in-one system. In addition to high-performance image acquisition and processing, you can use built-in digital I/O and industrial communication options for dynamic, real-time communication and integration with industrial automation devices including programmable logic controllers (PLCs), human machine interfaces (HMIs), robotics, sensors, and industrial machinery. You can configure NI Smart Cameras with the included Vision Builder for Automated Inspection (AI) software or program the camera with the LabVIEW Real‑Time Module and the Vision Development Module.
-
785151-01 -
NI
The ISC‑1782 is a high-performance smart camera for machine vision and is powered by a 1.58 GHz dual-core Intel Celeron processor. The combination of the onboard processor with a CMOS image sensor provides an easily distributed all-in-one system. In addition to high-performance image acquisition and processing, you can use built-in digital I/O and industrial communication options for dynamic, real-time communication and integration with industrial automation devices including programmable logic controllers (PLCs), human machine interfaces (HMIs), robotics, sensors, and industrial machinery. You can configure NI Smart Cameras with the included Vision Builder for Automated Inspection (AI) software or program the camera with the LabVIEW Real‑Time Module and the Vision Development Module.
-
778998-01 -
NI
13-Bit, 32-Channel, 800 kS/s PXI Analog Output Module—The PXI‑6723 delivers low-cost, high-density analog outputs to meet a wide range of applications, such as stimulus-response, signal simulation, waveform generation, and actuator stimulation. In addition, the device provides eight 5 V TTL/CMOS digital I/O lines; two 24‑bit, 20 MHz counter/timers; and digital triggering and external clocking capabilities. The PXI‑6723 can replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators. You can control each data point for each channel to define common waveforms, such as square, sine, or sawtooth, as well as complex waveforms.
-
785144-01 -
NI
The ISC‑1781 is a high-performance smart camera for machine vision and is powered by a 1.58 GHz dual-core Intel Celeron processor. The combination of the onboard processor with a CMOS image sensor provides an easily distributed all‑in‑one system. In addition to high-performance image acquisition and processing, you can use built-in digital I/O and industrial communication options for dynamic, real-time communication and integration with industrial automation devices including programmable logic controllers (PLCs), human machine interfaces (HMIs), robotics, sensors, and industrial machinery. You can configure NI Smart Cameras with the included Vision Builder for Automated Inspection (AI) software or program the camera with the LabVIEW Real‑Time Module and the Vision Development Module.
-
785145-01 -
NI
The ISC‑1781 is a high-performance smart camera for machine vision and is powered by a 1.58 GHz dual-core Intel Celeron processor. The combination of the onboard processor with a CMOS image sensor provides an easily distributed all‑in‑one system. In addition to high-performance image acquisition and processing, you can use built-in digital I/O and industrial communication options for dynamic, real-time communication and integration with industrial automation devices including programmable logic controllers (PLCs), human machine interfaces (HMIs), robotics, sensors, and industrial machinery. You can configure NI Smart Cameras with the included Vision Builder for Automated Inspection (AI) software or program the camera with the LabVIEW Real‑Time Module and the Vision Development Module.
-
785147-01 -
NI
The ISC‑1781 is a high-performance smart camera for machine vision and is powered by a 1.58 GHz dual-core Intel Celeron processor. The combination of the onboard processor with a CMOS image sensor provides an easily distributed all‑in‑one system. In addition to high-performance image acquisition and processing, you can use built-in digital I/O and industrial communication options for dynamic, real-time communication and integration with industrial automation devices including programmable logic controllers (PLCs), human machine interfaces (HMIs), robotics, sensors, and industrial machinery. You can configure NI Smart Cameras with the included Vision Builder for Automated Inspection (AI) software or program the camera with the LabVIEW Real‑Time Module and the Vision Development Module.
-
Q7B301 -
Axiomtek Co., Ltd.
The Q7B301 is an ultra-compact Qseven reference carrier board which measures only 100 x 72 mm - the size is slightly bigger than a credit card. The Q7B301 is perfect for small box applications such as those found in the latest digital signs, kiosks and traffic control system. This Qseven application board offers various I/O connectors and flexible expansion features to reduce the design effort to the minimum. The Q7B301 also has an extended industrial grade operating temperature range of -40ºC to +85ºC to withstand the rigors of harsh environments. Axiomtek’s new Qseven Rev. 2.1 application board, Q7B301, is compatible with Qseven module – Q7M311 which is powered by the Intel® Pentium® Processor N4200 and Celeron® Processor N3350. Customers can emulate required functions on Q7M301 as a reference design board or integrate the Q7M301 directly into their product as the application board. Its minimum footprint also enables the maximum potential. The Q7M301 is especially suited for industrial IoT applications such as industrial control, medical imaging, digital signage, gaming machines, military, and networking. The Q7B301 comes with two PCI Express Mini Card slots and one SIM card slot for wireless communication (3G/4G, GPS, Wi-Fi and Bluetooth). For enhanced or high-definition audiovisual devices, the Qseven reference carrier board supports one HDMI and LVDS interfaces as well as HD audio and 4-channel digital I/O. More I/O interfaces include two Gigabit LANs with Intel® i211AT Ethernet controller, two RS-232/422/485, one USB 2.0, two USB 3.0, one SMBus, and one I2C. Furthermore, it has one SATA-600 interface for storage requirements.
-
NA345E -
Axiomtek Co., Ltd.
The fanless NA345E adopts the low-power consumption Intel® Celeron® processor N3350 (codename: Apollo Lake). It aims to provide small business and SOHO customers an energy-saving and cost-effective network appliance for solutions in VPN, content filtering, UTM, network security gateway, and firewall. The desktop NA345E supports one non-ECC DDR3L-1866 SO-DIMM socket providing system memory of up to 8GB; moreover, it offers one mSATA for storage. It is equipped with three 10/100/1000 Mbps LAN ports (Intel® i211 Ethernet controller). The network appliance platform also has two USB 3.0 ports and an RJ-type serial console port. The system features a watchdog timer for reliable operation. Additionally, it supports Linux operating system.
-
ER-X Series -
Panasonic Industrial Devices Sales Company of America
The ER-X Series Area Ionizers utilize the pulse AC ionization design to achieve high-speed charge removal of wide surface areas for high-volume production lines. In addition to supporting compressed air ionization, the ER-X also features both airless and low-pressure ionization modes for applications where tiny workpieces can be easily blown away. Additional features include automatic ion balance and discharge frequency control (manual control is also possible), flat discharge surface for easy cleaning, discharge needle air barrier design to reduce contamination of the needles, replaceable discharge needle unit for easy maintenance, and a dual head configuration for enhanced charge area and layout (2 different ionizer heads can be connected to a single controller).
