Showing results: 1381 - 1395 of 2272 items found.
-
781315-01 -
NI
14-Slot, Virtex-5 LX110 FPGA, MXI-Express CompactRIO Chassis - The NI‑9159 is a rugged MXI‑Express chassis for high-performance, high‑channel‑count applications. With the NI‑9159, you can add C Series I/O modules to your PXI system or industrial PC. You can daisy chain up to six NI‑9159 chassis in a single chain and connect up to eight chains to a single controller.
-
V1743 -
CAEN S.p.A.
V1743 houses VME (VME64X compliant) and Optical Link interfaces. The VME interface allows data transfers of 60 MB/s (MBLT64), 100 MB/s (2eVME), 160 MB/s (2eSST). The Optical Link supports transfer rate of 80 MB/s and offers Daisy chain capability. Therefore, it is possible to connect up to 8/32 ADC modules to a single Optical Link controller (Mod. A2818/A3818).
-
VX1720 -
CAEN S.p.A.
VX1720 houses VME (VME64X compliant) and Optical Link interfaces. The VME interface allows data transfers of 60 MB/s (MBLT64), 100 MB/s (2eVME), 160 MB/s (2eSST). The Optical Link supports transfer rate of 80 MB/s and offers Daisy chain capability. Therefore, it is possible to connect up to 8/32 ADC modules to a single Optical Link controller (Mod. A2818/A3818).
-
CAEN S.p.A.
The CPU controller is offered in three versions: BASIC, ADVANCED and FULL:- The BASIC version provides communication interface, RESET control, INTERLOCK control, and STATUS LED indicators.- The ADVANCED builds upon the above by adding beam handshake management connectors (CH-ON, GEN, VSEL, ISEL).- The FULL version provides a complete array of panel connectors, an ENABLE control section, and fan speed control.
-
Instron
Instron offers a wide range of Durability Testing Products such as Controller and Software modules, Hydropuls actuators (linear & rotary), Servo valves, Sensors, Power Packs & Accessories and Test frames & fixtures.
-
BW-LPD-DAQ4000 -
B&W Engineering Corp.
Computer based controller with predefined MIL-STD test sequences stored (New)Create unlimited custom tests with multiple vibration frequencies and acceleration and other parameters to meet unique requirements (New)
-
Renesas Electronics Corp.
Renesas' AEC-Q100 qualified 100V half-bridge drivers safely drive MOSFETs for bidirectional controllers in 12V to 48V automotive hybrid powertrains. The advanced ISL784x4 MOSFET driver family enables high current DC/DC conversion with adjustable dead time and maximum efficiency. The ISL784x4 drivers are also well suited for 12V to 24V bidirectional DC/DC converters, as well as other high current buck or boost applications.
-
VME385 -
AcQ Inducom
The VME385 Universal/Timer Controller VMEbus board is an ideal solution for automated test and measurement applications. The VME385 features eight timer/counter inputs, all inputs have an coaxial connector for the input range of +/- 10 V and high-voltage pins for the input range of +/- 300 V. The coupling of the inputs is either AC or DC. The VME385 provides 6 measurement functions: frequency, high-time, low-time, period, counter and phase measurements.
-
FLIR TrafiCam x-stream2 -
Teledyne FLIR
The FLIR TrafiCam x-stream2 combines a digital camera and video detector into a single vehicle presence sensor. Detecting moving and stationary vehicles at signalized intersections, TrafiCam x-stream2 transmits vehicle presence information to a traffic controller via detection outputs or TCP/IP communication for adaptive and responsive signal timing. Each cost-effective TrafiCam x-stream2 sensor helps reduce vehicle idling time and optimize traffic flow.
-
TrafiRadar -
Teledyne FLIR
FLIR’s TrafiRadar vehicle presence sensor is a combination of a video sensor and radar. TrafiRadar is typically used for stop bar and advance vehicle presence detection, traffic adaptive systems, and dilemma-zone protection and thus improves traffic safety and efficiency at signalized intersections. TrafiRadar will warn traffic light controllers whenever a vehicle is present in the dilemma zone, either extending green or red lights to improve overall safety.
-
NI
Digitizer Adapter Modules for FlexRIO can be used with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO to create a high‐performance instrument with customizable firmware. With sampling rates from 40 MS/s to 3 GS/s and up to 32 channels, these modules cover a wide range of requirements for both time- and frequency‐domain applications. Digitizer adapter modules also provide digital I/O capability for interfacing with external hardware.
-
ADLINK Technology Inc.
The COM Express Type 10 Mini (84 x 55 mm, credit card size) module is intended for low power platforms (TDP 12W and below), capable of entry level processing with ultra-low power consumption, while supporting graphics and optimized I/O count for mobile applications. Type 10 modules are targeted at handheld devices (smart battery) for industrial, medical, transportation, and controllers for outdoor applications.
-
Hilkar
Line and load reactors are generally serial-connected to the input and/or output terminals of three phase equipment such as motor speed controllers, inverters and UPS systems. These equipment make use of semiconductor switches such as IGBTs, thyristors, and diodes and therefore create harmonic distortion and high switching over-voltages (dv/dt). Use of such equipment has been becoming more widespread as the technology advances. However, the negative effects of these equipment should not be overlooked.
-
ViTec Co. Ltd
The number of the current hopper and the correct positioning, along with the indication of power and status, are displayed on the indicators. Four load cells are mounted on the cart. The system records the amount of material shipped from each hopper, and the total weight of the material in the trolley is also displayed. All information is stored in the controller memory for a specified time. After the necessary time intervals, the operator can rewrite the information on the USB drive for further processing.
-
DVTest Inc.
The DVTEST LD Positioner is a two-axis elevation over azimuth positioner, for precise angular positioning with full spherical coverage. The LD Positioner is designed for the precise characterization of lightweight devices. The positioner is constructed from a low-permittivity polymer, for minimal reflections and multipath. For increased accuracy, the motor is outfitted with an absolute encoder, and laser guided calibration. A USB controller is included, with the positioner operated via Python or Matlab software libraries.