Showing results: 166 - 180 of 276 items found.
-
MFA 01 set -
Langer EMV-Technik GmbH
The micro probes are used to measure magnetic fields and they have a high resolution. They measure magnetic fields up to 6 GHz, e.g. at signal conductors (150µm), SMD components (0603-0201) or IC pins. The MFA micro probes are guided by hand. An amplifier stage is integrated into the probe head. The amplifier stage (9V, 100mA) is powered via the Bias tee BT 706. It has an impedance of 50 Ohm. The micro probes are connected via the Bias tee BT 706 to a spectrum analyzer or an oscilloscope. Langer EMV-Technik GmbH includes correction lines in the delivery. With the help of the correction lines the probe output voltage is converted either into the respective magnetic field or to the current which is running through the conductor.
-
MFA 02 set -
Langer EMV-Technik GmbH
The two in the set included micro probes are used to measure low-frequency magnetic fields up to 1 GHz, e.g. at signal conductors (150µm), SMD componets (0603-0201) or IC pins. The MFA micro probes are guided by hand. An amplifier stage is integrated into the probe head. The amplifier stage (9V, 100mA) is powered via the BT 706 Bias tee. It has an impedance of 50 Ohm. The micro probes are connected via the Bias tee to a spectrum analyzer or an oscilloscope. The MFA 02 set delivery of Langer EMV-Technik GmbH includes correction lines. With the help of the correction lines the probe output voltage is converted either into the respective magnetic field or to the current which is running through the conductor.
-
4-20mA -
Riverhawk Company
Loop-Powered Transmitters convert the output from proximity probes, seismic sensors, into a 4-20mA DC current, which is proportional to the input being measured. The transmitter converts the displacement or vibration signal to DC voltage and/or current for a DCS or PLC system. They control a 4-20mA current loop for a specified vibration range (ex. 0-5 mils peak-to-peak). The transmitters have a two-wire hook-up, powered solely by the loop current and have a power supply range of 15 to 36 volts.
-
CA10 -
Teledyne LeCroy
The CA10 is a programmable and customizable interface device that seamlessly incorporates third party current transducers/transformers with Teledyne LeCroy oscilloscopes or motor drive analyzers. It allows the third party device to be recognized and operate as if it were a Teledyne LeCroy probe.
-
SEM -
JEOL Ltd.
Delivers the world's best resolution with the incorporation of the newly-developed, super-high resolution Gentle Beam (GBSH). In addition, the maximum probe current of the In-lens Schottky Plus gun has been increased from 200 nA to 500 nA.
-
DX-103 -
Dexing Magnet Tech. Co., Ltd
DX-103 Gaussmeter is a desktop gaussmeter.Which is based on he latest progress of the the Hall Effect magnetic field measuring instrument.Adapt the high stability constant current source circuit technology to design and manufacture. Test probes adapt imported GaAs linear Hall-chip, the difference between probes is small, which can be replaced directly when it is damaged, and is an ideal AC & DC magnetic field test instrument.
-
ScopeTester 5 -
DeltaTech Electronics
ScopeTester 5 is 5-channel oscilloscope tester for PCs. Unlike traditional oscilloscopes it is capable of continuous acquisition of signals without dead times. This feature gives exceptional diagnostic value. Available voltage ranges matches typical signals found in modern cars. The user may connect to vehicle sensors, actuators and other diagnostic equipment, such as current clamps, inductive and capacitive probes and other diagnostic probes.
-
inTEST Corporation
The primary element of the tester electrical interface is the Probe Pin Ring (PPR). Sometimes referred to as a ‘tower,’ this array of spring-loaded probes can be arranged to provide a controlled impedance path, a low leakage connection, a low inductance arrangement for high currents, or just about any connection characteristic you require. inTEST EMS provides electrical interfaces in various OEM-supported designs, inTEST standards, and custom configurations.
-
Integrated Geo Instruments & Services Private Limited
The instrument design incorporates several advanced techniques of digital circuitry to make it reliable Geophysical tool that provides high quality data useful for all types of mineral and groundwater exploration research etc. The SSR-MP1 sends the entire current into the ground without wasting power for constant current generation thus increasing the signal strength to probe deeper layers.
-
SX set -
Langer EMV-Technik GmbH
The SX1 set consists of 3 passive near field probes for making measurements in the development phase of E-field and magnetic field with a high clock frequency in the range from 1 GHz to 10 GHz. The probe heads of the set SX allow for measurements close to electronic assemblies, e.g. on single IC pins, conducting paths, components and their connectors, to localize interference sources. Field orientation and field distribution on an electronic assembly can be detected through trained use of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They have an internal terminating resistance.
-
DX-105 -
Dexing Magnet Tech. Co., Ltd
DX-105 Gaussmeter is a desktop gaussmeter. Which is based on the latest progress of the Hall Effect magnetic field measuring instrument.Adapt the high stability constant current source circuit technology to design and manufacture. Test probe adapts imported GaAs linear Hall-chip, the difference between any two probes is small, which can be replaced directly when it is damaged. DX-105 Gaussmeter is an ideal DC magnetic field test instrument.
-
MS2001L -
Metal Samples Company
The MS2001L is a microprocessor-based, field-mountable corrosion rate meter. This versatile instrument measures the instantaneous corrosion rate and electrochemical current between the electrodes of any standard 2-electrode linear polarization resistance (LPR) probe. Corrosion rate is displayed on the LCD display.
-
SSR-MP-ATS -
Integrated Geo Instruments & Services Private Limited
The instrument design incorporates several innovative features and advanced techniques of digital circuitry to make it a reliable Geophysical tool providing high quality data useful for mineral and groundwater exploration and any other Geophysical applications. The SSR-MP-ATS sends the entire current into the ground without wasting power for constant current generation thus increasing the signal strength to probe deeper layers.
-
Nortec -
Evident Scientific
Olympus extensive line of high performance eddy current scanners is available for use with Nortec Eddy Current Flaw Detectors. With a wide range of features consisting of speed ranges from 600 to 3000 rpm, frequency ranges from 100 Hz to 6 MHz, multiple connector types, and multiple probe types, our scanners offer a full range of application solutions.
-
RFS set -
Langer EMV-Technik GmbH
The RFS set consits of three passive near field probes designed for the use in a measurement scanner during the development of E-field and magnetic field. They are designed for frequency ranges of 30 MHz to 3 GHz. The probe heads of the RFS set allow for close measurements needed to correctly localize interference sources on an electronic assembly. They document the whole image of the device under test`s near field. The scanner probes have a sheath current attenuation and are electrically shielded. They are connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They do not have an internal terminating resistance. The measuring signal can be increased with PA 203 or PA 303 preamplifier. On request RFS, LFS and XFS scanner probes can be produced.
