Showing results: 151 - 165 of 2628 items found.
-
Milwaukee Electric Tool Corporation
A clamp meter is an electrical tester that combines a basic digital multimeter with a current sensor. Clamps measure current. Probes measure voltage.
-
Shenzhen Graigar Technology Co.,Ltd.
A clamp meter is an electrical tester that combines a basic digital multimeter with a current sensor. Clamps measure current. Probes measure voltage.
-
FD1772B -
Lisun Electronics Inc.
• Constant DC output 0-6A• Auto or manual current sweep output• 5 current range output• Output voltage range: 0-11.5V• Current accuracy ± (1%reading + 2digit)
-
U60 -
LEMSYS
To measure leakage current ID, IR at given voltage range.
-
-
Shanghai MCP Corp
.Monophase and triphase Balance measures.Widerband power measure up to audio frequency .Small power measure.Connection and operation simplicity.Accuracy:better than 2% at the full current and voltage scale .Protection against over-currents by fuses .Over current and over voltage indictor
-
KM-PS-302DII / 303DII / 305DII -
Kusam Electrical Industries Limited
* High Stability* ON/OFF output switch* Fixed 5V Supply output*Coarse & fine adjustment setting for both Voltage & Current.* Full scale long duration time output.*3 digit display for each Voltage & Current function.
-
FuG Elektronik GmbH
Autoranging power supplies are power supplies with stepless range adjustment . Within a fixed power limit - up to max. 9,000W - the full output power is delivered over a wide voltage and current range. The working range is not only extended by higher voltage, but also by higher current. The output voltage is between 150V and 3000V.
-
MPS-H-1 Series -
Matrix Technology Inc.
MPS-H-1 series DC power supply is a new generation of high-quality linear DC power supply, with remote voltage compensation function, automatic conversion of voltage stabilization and current, high stability, high reliability, high precision, and display output voltage and current at the same time. Very high cost-effective advantage.
-
NI
The Power Measurements Conditioner provides voltage and current signal conditioning for a supported data acquisition module or device to make up to four simultaneous power measurements per conditioner. It also includes attenuation for voltage channels up to 2,000 V and has power, communication, and signal lines for current measurements from current transducers.
-
Handheld Turns Ratio & Winding Resistance Tester TWR-H -
Amperis sl
TWR-H is a handheld, battery operated, fully automatic test set specially designed for turns ratio, phase shift, excitation current and winding resistance measurements of transformers. It can also perform demagnetization of these transformers. Transformer turns ratio is determined by applying AC voltage across high voltage winding, accurately measuring AC voltage across the corresponding unloaded transformer winding, and then displaying the ratio of these voltages. User can enter a transformer’s nameplate voltages, so that turns ratio deviation can be calculated. This feature eliminates any error otherwise caused by an operator’s manual calculation. TWR-H compares measured turns ratio with the nameplate ratio and prints out the % of error for each test. Transformer winding resistance is determined by injecting DC current through a winding, accurately measuring DC voltage across the winding, and then calculating resistance as the ratio of voltage and current. The device generates true DC ripple-free currents. Both the injection of the current and the discharge of energy from transformer magnetic circuit are automatically regulated.
-
PA30Bi-H -
Ponovo Power Co., Ltd.
PA30Bi-H is the panel-mounted type power amplifier model which can produce 3-phase current, with maximum RMS phase current of 30A and maximum output power of 450VA, and 4-phase voltage, with maximum RMS phase voltage of 250V and maximum output power of 75VA.
-
INA169 -
SparkFun Electronics
The INA169 is a “high-side current monitor,” which means that you place a resistor (a “shunt resistor”) on the positive power rail and the INA169 measures the voltage drop across that resistor. The INA169 outputs a small current based on the measured voltage drop. If you place a resistor from the output of the INA169 to ground, you can measure the voltage at the output.
-
JYV-40 -
Kingrun Instrument Co., Ltd.
JYV-40 segment voltage test equipment is made up of constant current source, voltage-checking circuit and control circuit. The output current is adjustable and stable. Measured voltage value can be shown by three and half digital voltmeter, it can test the DC interturn and segment voltage and also is the effective way of checking turn coil resistance equilibrium.
-
MCL-400IR+ -
MULTI MEASURING INSTRUMENTS Co., Ltd.
・About Ior Leakage CurrentRecently, the leakage current clamp meter is widely used for insulation control of low voltage circuit as the supplementary method of the insulation resistance measurement. The control of leakage current has the advantages to enable the prediction of insulation condition in the electrical power line without having to shut off the power. The leakage current (Io) includes the capacitive leakage current (Ioc)originated in the capacitance and the resistive leakage current (Ior) originated in the insulation resistance each related to the ground. It is considered that the measurement of resistive leakage current (Ior) is the very useful and effective method for the insulation control of low voltage circuit. However, it was difficult to measure the resistive leakage current (Ior)with traditional leakage current clamp meter. MCL-400IR new digital clamp tester enabled the measurements of the resistive leakage current (Ior)without voltage input(phase detection).