Showing results: 1816 - 1830 of 5316 items found.
-
SEP/SIP -
Nihon Denji Sokki Co., Ltd
There are analog phase control type DC power supply type and digital control type inverter energy saving type. We provide the most suitable equipment according to the current capacity and cycle time.If the "start command" is executed from the existing molding equipment, each mode of "alignment-pause-demagnetization" is continuously operated by the program inside the instrument. It is also possible to share an emergency stop signal and output an output current abnormality signal.
-
Edmund Optics Inc.
Amplifiers are used to amplify the energy output of photodetectors as well as convert their electrical signal for a number of illumination measurement or spectroscopy applications. Amplifiers are digital systems that amplify the low electrical current transmitted by photodetectors to easily detectable levels. Amplifiers also convert photodetectors' electrical current into voltage so that their signal may be read by other digital devices. Amplifiers are indispensable for nearly any light measurement applications by greatly increasing the usability of a detector system.
-
GX6377 -
Marvin Test Solutions, Inc.
The GX6377 3U PXI multi function switch card provides users with the ability to switch both high current and general-purpose signals using only one 3U PXI switch module. The card features multiple channels of high current switching capability for 10 A and 2 A applications as well as two, 16 x 2 switch matrix groups, which can also be configured as a 32 x 2 or 16 x 4 matrix.
-
CA1000D -
Tecpel Co., Ltd.
Measure current without disconnecting circuit under test. Measure to 1000A DC or AC. Outputs 1mV per Amp, operates on 2V range of any DMM.
-
MRU-21 -
Sonel S.A.
* earth resistance measurment with 3-pole method, * measurement of continuity of equipotential bondings and protective conductors with auto-zero function - with current 200mA, * resistance measurement using 2-pole method.
-
Beamex Oy Ab
We offer different electrical calibrators for electrical quantities. We mainly offer products for DC signals related to process calibration, such as current, voltage, resistance and frequency.
-
ADC Corporation
Voltage source of ±1000V, high-speed measurement up to 1000 readings/sec, current measurement resolution of 1fA, resistance measurement range 3x1017Ω and 5 1/2-digit display
-
UI2002A -
Lisun Electronics Inc.
• Measure Vrms, Irms, W, PF/Hz • Voltage range: 10~600V, Current range: 10~2000mA, Frequency range: 20~70kHz • Accuracy: Class 2
-
Merica Series-MPA75 -
Merica Technology Ltd
Minimum Center: 1.91 (75mil)Current Rating: 3amps, continuousCurrent Resistance: 40milliohmsMounting Holes Size: 1.35Full Stroke: 6.35mmRated Stroke: 4.30mmSpring Force: 198gf(7oz)
-
TSMC 22ULLLDO -
DOLPHIN Design
*Low leakage current for best consumption in sleep mode*High PSRR to supply analog loads*Support input supply voltage up to 3.63V*Low quiescent
-
-
96040A Series -
Fluke Calibration
The 96040A RF Reference Source enables you to simplify your RF calibration system by replacing many of the instruments and accessories that make up your current system.
-
R2+ RTU -
Hsiang Cheng Electric Corp
*The R2+ Remote Terminal Unit (RTU) is a distributed architecture and large I / O capacity designed to meet the various demands of current Power SCADA / EMS applications.
-
IRIS Instruments
In fresh water environment, the standard Syscal Pro can be used for marine resistivity profiling. However, in highly conductive environment, a modified variant with higher current output is required.
-
KT7120 -
Ketai instrument (kunshan) Ltd.
1000A pointer clamp meter clamp head opening 48mmAC current can be measured 0~1000AAC voltage can be measured 0~600V mechanical lock needle function