Showing results: 4576 - 4590 of 5270 items found.
-
40-675-002-10/16 -
Pickering Interfaces Ltd.
The 40-675 series of very high density low cost multiplexer modules are available in a versatile range of switching configurations. The modules are supplied pre-configured in one of six multiplexer modes suitable for signal routing in high channel count ATE and data acquisition systems. The modules use high quality electromechanical signal relays allowing each channel to switch current up to 1A at 150VDC/100VAC. Connections are made via a front panel 200-pin connector.
-
40-583-001 -
Pickering Interfaces Ltd.
The 40-583 is a 256 crosspoint PXI matrix with dual pole switching. The module consists of a 64x4 matrix of 2-pole electro-mechanical relays with 2A current handling. The module is designed for switching medium voltage and power signals, typical applications include signal routing in ATE and data acquisition systems. The user signal connection is via a robust 160 pin DIN 41612 connector that is fully supported by the wide range of Pickering Interfaces cable and connector accessories.
-
40-582-001 -
Pickering Interfaces Ltd.
The 40-582 is a 256 crosspoint PXI matrix with dual pole switching. The module consists of a 16x16 matrix of 2-pole electro-mechanical relays with 2A current handling. The module is designed for switching medium voltage and power signals, typical applications include signal routing in ATE and data acquisition systems. The user signal connection is via a robust 78 pin D-Type connector that is fully supported by the wide range of Pickering Interfaces cable and connector accessories.
-
40-675-002-5/32 -
Pickering Interfaces Ltd.
The 40-675 series of very high density low cost multiplexer modules are available in a versatile range of switching configurations. The modules are supplied pre-configured in one of six multiplexer modes suitable for signal routing in high channel count ATE and data acquisition systems. The modules use high quality electromechanical signal relays allowing each channel to switch current up to 1A at 150VDC/100VAC. Connections are made via a front panel 200-pin connector.
-
40-580-001 -
Pickering Interfaces Ltd.
The 40-580 is a 256 crosspoint PXI matrix with dual pole switching. The module consists of a 32x8 matrix of 2-pole electro-mechanical relays with 2A current handling. The module is designed for switching medium voltage and power signals, typical applications include signal routing in ATE and data acquisition systems. The user signal connection is via a robust 160 pin DIN 41612 connector that is fully supported by the wide range of Pickering Interfaces cable and connector accessories.
-
Element 1 Power Systems Inc.
The fuel cell will change our lives as much as the computer it powers and the internal combustion engine it replaces. The future of power and transportation will change dramatically when fuel cells become the main producers of clean energy. The car will no longer be an environmental burden, and the electrical grid will be subdivided to the neighborhood and building level. The quality and reliability of this alternative energy source will be superior to the current grid design. Fuel cells and hydrogen technology will make all of this possible, and with little or no pollution.
-
Parrot Invent
Multimeter Test Probes, Voltmeter test leads,with the Parrot™ Clip Invention provide precise, HQ, accurate, reliable contacts and connections. Parrot™ Clips with HQ leads and banana plugs or other connectors are the best solution for DDM, analog multimeter for high voltage measurements as well as for high current measurements. Measurements with multimeter test probes require both: Hands-on direct point contact and grip on, Hands free removable connection.
-
VPG Transducers
The heart of each weighing system is a load cell. Load cells are mechanical components which act as force sensors by employing strain gages to provide an electrical output proportional to the applied force. Typically the electrical output is either analog (voltage or current) or digital. Load cells have specific mechanical packaging and sensing orientation to fit into electronic scales, and testing and monitoring systems. Load cells can be used for tension, compression, and/or shear measurement.
-
Analog Devices Inc.
Analog Devices offers a broad line of series voltage references with low dropout, low power, and excellent line regulation. These devices are voltage references that are functionally similar to a three-terminal regulator. Some series voltage references are designed to also operate in shunt mode by biasing the output pin and leaving the input pin open circuit. Series mode voltage references have the advantage that they draw only load and quiescent current from the input supply.
-
VCi-3™ -
ndb Technologies Inc.
The VCi-3™ system is designed for cable and phase identification, mainly for installation or maintenance purposes on three-phase electrical networks during power shutdowns.The transmitter module injects a low current on the cable conductors by direct contact or magnetic clamps methods. A voice message is recorded by the user and will be transmitted along with digital signals. Groundings stay connected at both ends of the three-phase circuit during the test. The detector module is used at the other end of the cable system.
-
FB305M -
Matco Tools
Can test circuit current up to 30 Amps - an easy way to check fuel pump amperage. Clever design allows for easy connection into fuse sockets. Fuse Buddy ends are molded into the shape of the fuse itself. During testing the fuse is removed and replaced into the Fuse Buddy. This way, the circuit being tested maintains fuse protection. Fuse Buddy stays put & won't fall out of the socket, like test probes do.
-
TOB-IT8512 -
Xiamen Tob New Energy Technology Co., Ltd
IT8512 120V/30A/300W DC Programmable Electronic Load for Battery and Power Supply TestHigh performance and affordable single channel DC electronic load. TOB-IT8512 DC electronic loads provide you with the flexibility to test a wide range of applications from power supply, charger to battery. The high resolution voltage(1mV), current(0.1mA) measurement system provides both accuracy and convenience, and eliminates the need for a DMM, external shunts and wiring.
-
FST-TA -
Foresight Electronics Co., Ltd.
Continuous 24/7 on-line monitoring One CELLCHECK monitor one cell, including internal resistance, voltage and temperature Software is available to collect data from CELLCHECK Serial port with Optical isolation, meet MODBUS protocol, easy to be accessed by UPS controller Easy to install without specialized training Full resistance, battery temperature and voltage monitoring for comprehensive battery state of health analysis String current and ambient temperature monitoring
-
DPM -
Bee Instruments
Digital panel meters are digital displays intended to be mounted in a panel, such as a control panel. They typically read some type of input, be it a voltage, current, or resistance, and display its value digitally. Often this input is a measurement from a sensor which is converted and displayed as a temperature, pressure, or other system variable. These meters may also act as simple controllers which trip a switch or perform a simple function when the reading reaches a preset measurement.
-
64970 -
Lisle Corp.
Replaceable in-line fuses protect both the meter and tester in the event a high current source on the vehicle is left on. The multimeter is bypassed with the switch during connection in case of a power surge. The tester and meter can remain connected until other computer systems shut down, isolating the drain. As a convenience, stacking banana connectors are used on the tester. This allows voltage to be measured on various locations on the vehicle during the drain test, using standard test leads.
