Filter Results By:

Products

Applications

Manufacturers

Data

elemental component of knowledge able to be processed.

See Also: Data Analytics, Analysis


Showing results: 6466 - 6480 of 8175 items found.

  • Open Source Logic Analyzer

    Logic Pirate - Seeed Technology Inc.

    8 channels 256,000 Samples recording size 20 MHz sampling speed, can potentially be overclocked to 60 MHz No compromise on sample size when combining different speeds or number of channels Simple configurable edge detection triggers on all inputs (simple OR trigger) Configurable ratio of samples from before and after the trigger (rolling sample buffer) 5 V tolerant inputs (LOW-level voltage < 0.8 V, HIGH-level voltage > 2.0 V) About 500 kB/s transfer speed to the PC (256 kSamples take about 0.5 seconds) Data capturing can be stopped from the host software anytime Cross platform host software for Windows, OS X, and Linux DIY-friendly 0603 parts and SOIC packages used on a 2-layer board On board 3.3 V regulator can supply up to 400 mA to an external circuit Tiny 3cm x 3cm PCB Firmware updates via built-in USB bootloader Probe cables and acrylic case available from Seeed Studio Open source PCB (EAGLE) and firmware files

  • Serial to Ethernet Connector

    Eltima Software

    With Serial to Ethernet Connector you can share up to 255 serial devices over network turning your computer into a terminal server. With this serial over network solution any device connected to a COM port can be accessed and used from any spot on the globe as if it were physically connected to the local machine. The data sent by serial port device is transmitted over a TCP/IP network. This is achieved thanks to our virtual serial port technology that emulates standard COM ports behavior and Windows OS treats the virtual ports as the real ones. Although the ports are treated as physical you are not limited to the quantity of physical COM ports and can create COM port connections without occupying real serial ports. With Serial to Ethernet Connector you can: share serial port for incoming connections, connect the port to remote host, or share port using UDP connection. Starting from version 7.0 Serial to Ethernet Connector got absolutely new user interface for even easier creation and management of connections with latter conveniently visualized and more.

  • USB 3.0 Cameras With CCD

    xiD - XIMEA GmbH

    *Quality components - Sony "EXview HAD CCD II" sensors delivering 2.8, 6.1, 9.1 and 12 Mpix*Fastest - Highest speed using full 4 TAP readout potential*Industry standard interface - Compliant with USB 3.0 SuperSpeed specification*Versatile mini camera - Subtle 60 x 60 x 39 mm, 320 grams (1)*Power - Lowest power consumption starting at 3 Watt, bus powered with USB3 cable*Cool - Minimal heat dissipation with passive COOLing*Compatibility - USB 3.0 support for Windows 7 and 10, macOS, Linux, ARM and 30 Libraries*Connectivity and Synchronization - Programmable opto-isolated input and output, 3 status LEDs*Bandwidth potential - 5Gb/s interface 400Mpix/s data throughput*Software interfaces - GenICam / GenTL and highly optimized xiAPI SDK for Image Processing*High grade - Quality class of sensors is combined with specially selected IR filters *Easy deployment - Range of accessories and widest hardware and software interoperability*Highly Customizable - Available in Board level and with Peltier TE Cooling

  • USB PD Power Supply/Module ATS

    8000 Series - Chroma ATE Inc.

    The USB 3.1 specifications has three major features which are 10Gbit/s transmission speed, USB PD (Power Delivery) with support for 100 watt charging power, and the standard Type-C connector/cable that can be inserted with either side. It is expected to meet all kinds of data / video transfer applications. The advent of USB PD may consolidate the specifications of various power converters and the laptop, monitor, printer or Hub that implements USB PD is no longer a simple power-consuming device but able to supply power to other devices. The USB PD DRP (Dual role port) function allows the built-in USB PD module to deliver a maximum of 100 watts of power through the Type-C interface. To make sure the USB PD Type-C output power does not supply invalid voltage or poor power output characteristics with excessive noise that can damage the power consuming device and cause unsuccessful startup, each USB PD power supply or module has to be fully tested during production to ensure the product features meet the design specifications. This ensures high-quality products are provided to the market to gain acceptance.

  • Basic Quad J-Type Analog Thermocouple Amplifier

    SEN-30103-J0 - Playing With Fusion Inc

    Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.

  • Basic Quad J-Type Analog Thermocouple Amplifier

    SEN-30103-J1 - Playing With Fusion Inc

    Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.

  • Basic Quad K-Type Analog Thermocouple Amplifier

    SEN-30103-K0 - Playing With Fusion Inc

    Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.

  • Basic Quad K-Type Analog Thermocouple Amplifier

    SEN-30103-K1 - Playing With Fusion Inc

    Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.

  • EMI Receiver

    KH3935 - Beijing KeHuan Century EMC Technology Co,.LTD

    KH3935 type EMI test receiver interference test receiver is fully automatic, is EMI major tool for testing. The frequency range of the KH3935 receiver is from 9kHz to 30MHz , which satisfies the power line disturbance power test. After configuring the artificial power network, the power terminal disturbance voltage test can be performed. The machine has fast test speed, strong maneuverability, stable performance, Advantages such as convenient test data processing. The KH3935 receiver uses a USB interface for data transmission, and supports USBinterface peripheral devices such as printers, mice, keyboards, etc. The machine is equipped with a high-speed and large-capacity hard disk, which stores a variety of external device data, and supports plug and play. External test equipment. The software is self-developed by our company, using windows as the carrier, users who are familiar with the operation of windows can quickly get started. The machine can independently carry out test work without additional control equipment for control operations, which fundamentally solves the problem of interference sources. The measurement results can be input to the hard disk in the receiver or stored in a floppy disk through a floppy drive or printed out directly or savedusing a USB storage device. The detailed measurement report can be printed directly according to user needs without additional editing.

  • EMI Receiver

    KH3939 - Beijing KeHuan Century EMC Technology Co,.LTD

    KH3939 type EMI test receiver interference test receiver is fully automatic, is EMI major tool for testing. The frequency range of the KH3939 receiver is from 9kHz to 300MHz , which satisfies the power line disturbance power test. After configuring the artificial power network, the power terminal disturbance voltage test can be carried out. The machine has fast test speed, strong maneuverability, stable performance, Advantages such as convenient test data processing. The KH3939 receiver uses a USB interface for data transmission, and supports USBinterface peripheral devices such as printers, mice, keyboards, etc. The machine is equipped with a high-speed and large-capacity hard disk, which stores a variety of external device data, and supports plug and play. External test equipment. The software is self-developed by our company, using windows as the carrier, users who are familiar with the operation of windows can quickly get started. The machine can independently carry out test work without additional control equipment for control operations, which fundamentally solves the problem of interference sources. The measurement results can be input to the hard disk in the receiver or stored in a floppy disk through a floppy drive or printed out directly or savedusing a USB storage device. The detailed measurement report can be printed directly according to user needs without additional editing.

  • Custom Testing Solutions

    Enable Integration

    Test and MeasurementEnable increases the robustness of your test and measurement solutions, thereby reducing errors and associated costs. Data Acquisition (DAQ)Enable defines and builds custom DAQ systems for automated measurements of any process or manufactured part. Control and AutomationEngineeringEnable ensures that your processes are programmed to be safe, effective and optimized for both speed and quality. Real-Time and Mission CriticalSystemsEnable develops dependable real-time systems and Hardware in the Loop (HIL) simulations for high-speed applications. Motion ControlEnable creates software for synchronized multi-axis robotic control of velocity, position, force and action. Machine VisionEnable implements software and hardware-based solutions for precise image analysis, data extraction and vision-guided machine control. R&D Systems/Product DevelopmentEnable’s team of engineers and scientists works with you to address and solve problems containing technical challenges and uncertainties. Electronic Test SystemsEnable programs and builds software and hardware-based solutions for accurate measurements, from DC to RF. Mobile App DevelopmentEnable enhances your systems by integrating custom iOS and Android apps. Web DevelopmentEnable enhances your systems by integrating desktop and mobile web frameworks using PHP, CSS and HTML5. Database DevelopmentEnable decentralizes your data storage to be online, secure and accessible from anywhere.

  • Powered VME430 Crates

    6U VME430 6023 - W-IE-NE-R, Plein & Baus GmbH

    The WIENER VME 6023 crate series is the newest generation of 19" integrated packaging system for standard VME/VME64 bus systems with 6Ux160mm cards. Designed primarily for applications in nuclear and high energy physics data acquisition, beam line control and test instrumentation it combines superior mechanical quality with lowest noise power supply technology.

  • DC Source/Calibrators

    Krohn-Hite Corporation

    Our DC Source/Calibrators are designed for a typical applications such as the design, check and calibration of high speed, high resolution A/D converters; design and certification of high speed data logging and process control systems; calibration of digital voltmeters and multimeters; as an “IMBEDDED STANDARD” and/or simulator; design, testing, simulation and certification of thermocouples, strain gages and transducer instrumentation.

  • Multi-channel low-pass filter board

    AAF-2 - Alligator Technologies

    The AAF-2 is a multi-channel low-pass filter board designed for use in front of A/D converters with resolution up to 16-bits.  It is ideal for filtering applications in sound and vibration testing, ultrasonics, acoustics, structural analysis, industrial, test, scientific and laboratory data collection and applied mechanical applications in electronics, aerospace, field research, automotive, and process control industries.

  • Energy Analyzer

    EP600i - CANDURA Instruments

    The EnergyPro EP600i is portable and easy to use. Perfect for single phase or three phase energy consumption analysis and basic power quality monitoring. It supports standard wiring configurations and comes with a set of 1A - 2500A WideRangeFlexCT ™. The graphics display makes setup very easy and intuitive - you can setup and record data without looking at the manual!

Get Help