Showing results: 211 - 225 of 251 items found.
-
NI
Industrial Controllers are high-performance, fanless controllers that provide connectivity for communication and synchronization to EtherCAT and Ethernet CompactRIO chassis, EtherCAT motion drives, GigE Vision and USB3 Vision cameras, and other automation equipment. Controllers also have onboard isolated, transistor‐transistor logic (TTL), and differential digital I/O. You can use LabVIEW system design software to create, debug, and deploy logic to both the onboard FPGA and the processor. LabVIEW contains over 950 signal processing, analysis, control, and mathematics functions to accelerate development.
-
HA4600/RF -
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HA4600/RF series is the narrow-band multiplexing EDFA which suitable with CATV application. This EDFA build-in one unit 1550nm direct modulated CATV transmitter used in inter cutting local VAD service. Build-in WDM multiplexing TX optical signal and External input optical signal of the main road then enter EDFA amplification, to server the local users. In order to avoid TX output optical power and the external input optical power does not fit the main road interfere with each other, the output power of the TX through the build-in VOA, from front panel adjust and set. The whole unit is concision, install and debug convenient. Providing high-quality, low-cost solution for all-optical relay 1550nm optical CATV systems, second-grade service area or administration village inter cut local VAD service.
-
N6705C -
Keysight Technologies
The N6705C DC Power Analyzer provides unrivaled productivity gains for sourcing and measuring DC voltage and current into the DUT by integrating up to 4 advanced power supplies with DMM, Scope, Arb, and Data Logger features. The N6705C eliminates the need to gather multiple pieces of equipment and create complex test setups including transducers (such as current probes and shunts) to measure current into your DUT. The DC Power Analyzer also eliminates the need to develop and debug programs to control a collection of instruments and take useful measurements because all functions and measurements are available at the front panel. For even greater control and analysis functions, the DC Power Analyzer can be used with the 14585A Control and Analysis Software. When automated bench setups are required, the N6705C is fully programmable over GPIB, USB, LAN and is LXI Compliant. 14585A Control and Analysis Software
-
ACCAT -
Huntron
The ACCAT is designed to support diagnostic and acceptance test requirements across a wide spectrum of testing parameters. ACCAT provides a suite of core parametric test instruments, advanced GUI based software, Huntron Access Robotic probing and Huntron Analog Signature Analysis (ASA). ACCAT provides stimulus and asurement capabilities necessary for full functional and parametric testing of circuit card assemblies along with robotic guided probes for fault verification and debug. The Huntron ASA test is ideal for pretest or safe to power up procedures protecting the integrity of the test system.
-
ScanTAP 4 & 8 -
Corelis, Inc.
Boundary-scan has proven itself time and again to be a truly versatile interface for structural test, embedded functional test, built-in self-test (BIST), software debug, and in-system programming. Supporting such diverse applications requires equipment with high-performance specifications and extended features.Corelis ScanTAP pods are designed for use with PCI-1149.1/Turbo and PCIe-1149.1 high-speed JTAG controllers. Featuring 4 & 8 independent Test Access Ports (TAPs), up to 80 MHz clock rates, and advanced TAP capabilities such as analog voltage measurement, the ScanTAP family of intelligent pods is the ideal JTAG interface for high-performance environments.
-
Corelis, Inc.
Corelis offers the BusPro-I™ and CAS-1000-I2C™ bus analyzer products to satisfy different technical needs and price points. Corelis bus analyzers and exercisers offer analysis, test, and debug capabilities for product development, system integration, and manufacturing of digital boards and systems. All of our bus analyzers are PC-based and come with a Windows-based software package.Both the BusPro-I and the CAS-1000-I2C/E are equipped with I2C Exerciser, a highly intuitive software package that lets you get the most from your I2C bus analyzer. Each is packaged in an attractive, integrated enclosure, for optimal bench-top and test floor convenience.
-
D9021HDMC -
Keysight Technologies
The D9021HDMC HDMI electrical performance validation and compliance software for Infiniium V, Z and UXR-Series oscilloscopes gives you a fast and easy way to verify and debug your High Definition Multi-media Interface (HDMI) designs for set-top boxes, Digital Video Recorders, DVD players, and motherboard systems. The HDMI compliance test software lets you automatically execute HDMI electrical checklist tests and displays the results in a comprehensive report format. In addition to the measurement data, the report provides a margin analysis that shows how closely your device passed or failed each test.
-
Circuit Check, Inc.
Circuit Check’s wireless fixture technologies reduce debug time, simplify ECO’s and reduce maintenance. This allows for the highest test performance, ability to probe denser smaller targets and achieve ultra-high node counts. Higher density more complex circuit boards complicate testing requirements. Smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board (T-Board).
-
SA831 -
Hangzhou Softel Optic Co., Ltd.
*The microwave low noise amplification circuits are used as forward and backward paths of SA831 products. CATV special RF modules encapsulated by SOT-115 are used as forward paths of SA831 products. The microwave low noise amplification circuits are used as backward paths of SA831 products.*It is more convenient to debug, because of plug-in duplex filters, plug-in fixed (or adjustable) equalizers, plug-in fixed (or adjustable) attenuator plug-in output splitters and scientific and rational on-line detection ports.*The equipment can work steadily outdoor under bad environmental condition, because of waterproof aluminum case, high reliability switching power supply and lightning protection system.
-
Response Dynamics Vibration Engineering, Inc.
We have consulted on thermal issues ranging from conduction issues in TECs, thermal radiation modeling, and countless air cooled system issues relating to system performance, vibration, and acoustics noise. We use a wide array of thermocouple instrumentation, thermal imaging, flow measurements, as well as finite element analysis and analytic modeling to measure, design, and debug thermal and related issues. We often work on customer products in our Response Dynamics lab where we characterize the system, engineer solution options, and prototype solutions. We then work with the customer to work the winning solution into their quality control and manufacturing process.
-
JTAG Technologies Inc.
While many ICs are equipped with a JTAG (IEEE Std. 1149.1) boundary-scan register (BSR), a significant number of microprocessors and DSPs can be found with deficient or even non-existent BSRs. CoreCommander Micro uses the on-chip debug mode of processors to access ports and embedded peripheral controllers to promote ''kernel-centric'' testing. Similarly, in the case of today's Field Programmable Gate Arrays (FPGAs) test engineers can ''bridge'' from the JTAG interface to the resources of the gate array itself. Our CoreCommander FPGA product implements a translatorinterface that allows our JTAG hardware to control embedded IP cores via a variety of bus interfaces (e.g. Wishbone Avalon etc.).
-
Teledyne LeCroy
Gen-Z is a data-access technology designed to provide high-speed, low-latency, memory-semantic access to data and devices via direct-attached, switched or fabric topologies. Gen-Z components use low-latency read and write operations to directly access data and use a variety of advanced operations to move data with minimal application or processor involvement. Gen-Z fabric utilizes memory-semantic communications to move data between memories on different components with minimal overhead. Memory-semantic communications are extremely efficient and simple, which is critical to delivering optimal performance and power consumption. Teledyne LeCroy provides protocol analysis and error injection test equipment to support development and debug of Gen-Z based devices
-
Teledyne LeCroy
Compute Express Link (CXL) is a new high-speed CPU-to-Device and CPU-to-Memory interconnect designed to accelerate next-generation data center performance. CXL technology maintains memory coherency between the CPU memory space and memory on attached devices, which allows resource sharing for higher performance, reduced software stack complexity, and lower overall system cost. This permits users to simply focus on target workloads as opposed to the redundant memory management hardware in their accelerators. CXL is based on a PCI Express 5.0 Physical layer with speeds up to 32GT/s. Teledyne LeCroy provides protocol analysis test equipment to support development and debug of CXL based devices.
-
GoLogicXL-36 -
NCI Logic Analyzers
Logic analyzers and oscilloscopes offering fast sample rates and large memory depths are required to debug and test modern electronics. The GoLogicXL captures a very large window of bus activity using sample depths up to 1 billion samples. 4 GHz sampling rates expose the finest details in your signals. 1 GHz Transitional sampling provides the optimum method to capture fast data bursts separated by seconds, minutes, or even hours of bus inactivity. The GoLogicXL State analysis can also synchronize with single-data-rate 300 MHz SDR clocks, and double-date-rate 250 MHz DDR clocks (500 MHz effective).
-
GoLogicXL-72 -
NCI Logic Analyzers
Logic analyzers and oscilloscopes offering fast sample rates and large memory depths are required to debug and test modern electronics. The GoLogicXL captures a very large window of bus activity using sample depths up to 1 billion samples. 4 GHz sampling rates expose the finest details in your signals. 1 GHz Transitional sampling provides the optimum method to capture fast data bursts separated by seconds, minutes, or even hours of bus inactivity. The GoLogicXL State analysis can also synchronize with single-data-rate 300 MHz SDR clocks, and double-date-rate 250 MHz DDR clocks (500 MHz effective).
