Showing results 346 - 360 of 539 products found.
-
Mass Flow - Ono Sokki
This system uses two detectors, the FP-2140H volumetric flow detector and the FZ-2200 mass flow detector. Volumetric flow rate detected in high accuracy is converted to mass flow rate using density measurement values. Each value of the detector can also be displayed independently.
-
Bank Elektronik
Potentiostats are widely used in research: materials science, corrosion research and active corrosion control require potentiostats. In analytical chemistry, methods like cyclic voltammetry have equal rights as chromatography and spectroscopy. The core of analysing instruments like gas detectors, blood sugar meters and many others is a potentiostat.
-
Xenemetrix Ltd.
Complete XRF analysis is possible, with or without standards, using an internal database of fundamental parameters and complete modeling of detectors and sources. Spectrum processing libraries are available for removing spectrum artifacts (escape and sum peaks), background and for various least-squares peak-fitting models using synthetic Gaussian or experimental reference profiles.
-
SONOTEC Ultraschallsensorik Halle GmbH
The non-invasive ultrasonic detection of air bubbles in fluid-filled tubes plays an important role in many fields of science and industry. Ultrasonic air bubble detectors are used in many areas, including medical technologies, the pharmaceutical industry, the foodstuffs industry, automation and process control.
-
ORTEC
Scintillation detectors produce light as they absorb energy, and these light flashes result in the release of a proportionate number of photoelectrons at the cathode of a photomultiplier tube (PMT). Each of the ORTEC Photomultiplier Tube Bases is designed to accommodate a particular type of PMT to distribute the operating voltages to all its elements, and to derive signals from it.
-
Heraeus Noblelight GmbH
The PID technique uses a lamp with known photon energies in the vacuum ultraviolet (VUV) region.The output from the lamp is used to photoionise gaseous molecules with ionisation potentials lower than the photon energy emitted. Typical photoionisation detectors measure volatile organic compounds (VOCs) and other gases in concentrations from the ppm to ppb level.
-
Buckleys Ltd.
PD and PHD Pinhole/Holiday Detectors have an alarm circuit to alert the operator when a fault has been located and the required test voltage can be set on the unit's meter. Spark Testers provide an inexpensive means of testing but have no output voltage meter or audible alarm. However, they can test joints even if the backing is not connected.
-
AKV 9310 - Haefely Hipotronics
HAEFELY HIPOTRONICS offers a broad range of partial discharge and radio interference voltage (RIV)equipment, from simple discharge meters and calibrators to sofisticated digital detectors with noise suppresion and diagnostic capabilities. Our partial discharge equipment measures according to international standards and the results are accepted worldwide.
-
Fortress Technology Inc.
Available in aluminum or stainless steel with a wide variety of aperture sizes, Phantom Metal Detectors are built rugged to withstand the harshest applications. For heightened stability and performance in wet product applications, the IP69K certified BSH Extra Rugged Casing is utilized. An epoxy chute provides a complete waterproof seal on IP69K rated units.
-
Bunkoukeiki Co., Ltd
It is a spectrometer that reduces the aberration of the optical system to the utmost limit because it measures effectively using multichannel detectors such as CCD, CMOS, InGaAs etc. Since the spatial resolution is high on the whole surface of the light receiving surface of the detector, it can be used for the following applications.
-
Solo 423 / 424 - Detectortesters
Available in both 110 / 120 and 220 / 240 volt versions the Solo 423 and 424 are the professionals’ choice where cables and leads are acceptable. Unconstrained by energy availability they provide the quickest of test times and are, perhaps, most suitable for the highest temperature detectors.
-
Solo 461 - Detectortesters
Functional checking of heat detectors, with a genuine heat source, is now required by major national standards around the world. Testing with heat sources not designed for the purpose can be both dangerous and damaging. The Solo range of heat detector testing equipment, designed specifically for the purpose, provides a genuine professional’s solution.
-
LC-4000 Series - Jasco Analytical Instruments
The LC-4000 Series UHPLC system offers high performance separations at up to 130MPa (around 20,000psi) for use with the smallest particle sizes and longest column lengths. The pump, autosampler and detectors are optimized for the smallest band broadening and fastest cycle times.
-
Bentham Instruments Ltd
All our spheres can be coupled to our high performance spectroradiometer systems for UV-visible-IR spectral power distribution measurements yielding full colour information including colour rendering indices, chromaticity co-ordinates, colour temperature, etc. Alternatively precision photometric detectors can be fitted for direct total lumen output measurements.
-
1010 - Dexter Research Center, Inc.
A low noise, DC-coupled amplifier is packaged in a rugged, die-cast aluminum case with BNC connectors enabling input and output. Provides very low voltage noise and current noise in the critical region of 0.1 Hz to 10 Hz making this the ideal amplifier for thermopile detectors in sensitive systems design and laboratory experiments.
