Filter Results By:

Products

Applications

Manufacturers

Detectors

register the presence of a stimuli.

See Also: Metal Detectors, Particle Detectors, Sensors, Charge Sensitive Preamplifiers


Showing recent results 526 - 540 of 541 products found.

  • Earth Sensors

    Optical Energy Technologies, Inc.

    The earth sensor is composed of four thermopile-optical assemblies viewing four fields of view through a single 13.5mm cut-on optical filter/window, as is shown in Figure 1. Each earth sensor measures the attitude of the spacecraft relative to its axis. For Pitch and Roll attitude readout, two sensors mounted 90° apart around the spacecraft’s yaw axis are required, as is shown in Figure 1. Each sensor is mounted such that the lower edges of its fields protrude 10° below the nominal earth horizon at the orbit altitude. The output of each field is a D.C. voltage proportional to the earth radiance multiplied by the solid angle subtended by the earth in that detector’s field. Two additional detectors are used to correct for earth radiance variation as a function of season and position in the orbit. One of these fields views cold space continually, while the other is always below the earth horizon and thereby measures the earth radiance in the vicinity of the spacecraft’s position in the orbit.

  • EMC Precompliance Set

    EMC-SET - Rohde & Schwarz GmbH & Co. KG

    The EMC precompliance sets include the following:HMS-X with HMS-EMC EMC and preamplifier option (EMC-SET2: HMS-3G option included)Frequency range from 100 kHz to 1.6/3 GHzFast sweep modeReceiver mode with quasi-peak detectorVarious detectors: auto peak, min./max. peak, sample, RMSHM6050-2 (LISN)Frequency range from 9 kHz to 30 MHzBuilt-in transient limiterArtificial hand connector(HZ540 (EMC-SET2))Frequency range from 100 kHz to 1/3 GHzProbes included (1 × E-field probe, 1 × H-field probe, 1 × high-impedance probe)EMC PreComEMC Precompliance Software (EMC PreCom) -- EMI module part of the HMExplorer software for conducting precompliance measurements (only with HO720 USB/RS-232 or the optional HO732 Ethernet/USB interface)

  • Multi-angle Polarized Light Scattering Measurements

    LISST-VSF - Sequoia Scientific, Inc.

    In-situ measurements of P11, P12 and P22 elements of scattering Mueller matrix, (P11 is VSF) from 15-150º.VSF (P11) only at small angles, 0.05 to 10º in 32 logarithmic steps in angles.Only two detectors employed with absolute radiant sensitivity (A/W) calibration.Beam attenuation measured with optics similar to our LISST-100X.Roving Eyeball™ optics permit 1-degree resolution in angles between 15 -150º.Sampling rate at 3 seconds per measurement set (involves 3 turns of Roving Eyeball with unpolarized, vertical, and horizontal polarized laser).Daylight rejection by laser modulation.Dynamic range in VSF measurements extended via laser power modulation.Data from small and large angles in a single data stream, including depth and temperature.

  • Photoluminescence Spectrometer

    FLS1000 - Edinburgh Instruments Ltd

    The FLS1000 sets the standard in both steady state and time-resolved photoluminescence spectroscopy for both fundamental research and routine laboratory applications. The system is a modular fluorescence and phosphorescence spectrometer for measuring spectra from the ultraviolet to the mid-infrared spectral range (up to 5,500 nm), and lifetimes spanning from picoseconds to seconds. All of this can be achieved through various upgrade routes, either at the time of order or in the future. Whether you are studying photophysics, photochemistry, biophysics, biochemistry, material or life sciences, the FLS1000 will enable you to reliably and accurately measure luminescence spectra and kinetics using state-of-the-art sources, detectors, acquisition techniques, quality optics and precision mechanics. The large sample chamber will house practically any type of sample accessory.

  • Multi Interface USB Adapter

    SUB-20 - Dimax

    SUB-20 is a versatile and efficient bridge device providing simple interconnect between PC (USB host) and different HW devices and systems via popular interfaces such as I2C, SPI, MDIO, RS232, RS485, SMBus, ModBus, IR and others. It is also a full "any to any" converter between all supported interfaces and I/O features. SUB-20 is a powerful I/O controller with 32 GPIO, 8 Analog Inputs, PWM Outputs, Edge DEtectors, LCD, Leds and push buttons.SUB-20 system includes SW package containing driver, API Library, GUI and Command Line based applications, C,C++,C#,VB.net, MATLAB, LabView sample code and documentation. SUB-20 can be used with PC 64/32 bit running Windows 2000/XP/Vista/Win7/Win8, MacOS, Unix/Linux and DOS.Working with SUB-20 does not require deep knowledge of low layers of the specific interface. All you need to do is to call right API function at the right place. And this is really very easy as API functions are well documented and "exampled". API set is relatively small but comprehensive.SUB-20 is equipped with status Leds, optional LCD and buttons. All this guarantee fast and comfortable development, field debugging and maintenance of applications including option of standalone operation.

  • Radiometer

    X1-1-RCH-116-4 - Gigahertz-Optik GmbH

    The X1-1 radiometer from Gigahertz-Optik features an RCH-116-4 detector and is ideal for measurement of the irradiance of high power LEDs in the UV-A and blue light range. The device can accurately measure irradiance levels of up to 40,000 mW/cm². One of the outstanding features of the RCH-116-4 detector is its proven concept of a passive radiation absorber coupled to a UV sensor. This provides stability even in high temperature and intense UV radiation environments. In addition to the passive radiation absorber, the device also has a cosine-corrected field of view. The sensor’s housing also serves as a handle. The battery-powered X1-1 optometer supports a usable dynamic range from less than 1 mW/cm² to 40,000 mW/cm² thanks to its high-end signal amplifier. It can be used to perform precise measurements of up to 5 standard LED wavelengths for which the detector was calibrated for active irradiance. In addition to the CW measurement function, the device also has a dose measurement function. The radiometer can be used with other detectors from the RCH series. e.g. for gas discharge lamps. Remote control of the device is possible via its user software and a software development kit is offered for integration of the device in the user’s own software.

  • Spectral Response SystemsQuantum Efficiency SystemsIPCE Measurement Systems

    Photo Emission Tech., Inc.

    QE system provides electronics and software designed for fully automated measurement of external quantum efficiency of solar cells. All systems include probes and a fixed plate sample stage for samples up to 150 mm x 150 mm. The main system components include: custom designed software, measurement electronics, and computer system (Windows 8 operating system). The measurement involves focusing monochromatic light to a spot on the device under test, then accurately measuring the photon flux and current from the test cell. The system utilizes a dual beam configuration with lock-in detection, providing an absolute accuracy of ±3%. The QE system uses a grating monochrometer with silicon/InGaAs/Ge detectors. The system includes automatic order sorting filters and two light sources for monochromatic illumination (a Xenon- arc lamp and a halogen lamp). A single lock-in amplifier is used to measure both the reference detector and test device. The main system comes with all the hardware needed to measure quantum efficiency, a fixed plate sample stage and probes.

  • Ultra-Fast Micro-/Nano- FIB Machining

    XEIA3 - TESCAN Brno, s.r.o.

    Powerful ultra-high resolution SEM column equipped with a high brightness Schottky emitter for high currents, low noise and extraordinary imagingIn-Beam detectors for excellent imaging and very short working distancesUltra-fast xenon plasma ion source FIB high beam currents for outstanding milling speeds and an excellent performance in sputtering large volumes of material, and low beam currents for smooth polishingLess implantation, doping or degradation of insulator deposition, a valuable feature for semiconductor industrySimultaneous SEM imaging during FIB milling or deposition (the whole process can be observed directly) Unique and advanced TESCAN's technologies in terms of automated operations such as the In-Flight Beam TracingTM designed to accurately compute and adjust all the optimal parameters for high resolution imagingAdvanced patterning and 3D characterisations capabilities powered by DrawBeam, a pattern editing tool that also provides a real-time visualisation during milling or lithographic processesHigh-performance electronics for faster image acquisition up to 20 ns/pxl, an excellent deposition rate and ultra-fast scanningNovel solution for fast 3-dimensional microanalysis such as 3D EDX and 3D EBSD sample reconstructions12'', 8'' and 6'' wafer inspection by means of an extended chamber; an exclusive feature of TESCANUnique integration with TOF-SIMSGas Injection System (GIS) for enhancing your FIB applicationsPowerful turbomolecular and dry fore vacuum pump for keeping the chamber clean. Electron gun pumping by ion getter pump in ultra-high vacuum

  • USB Controlled RF Signal Generators

    Windfreak Technologies, llc

    Windfreak Technologies provides high value radio frequency devices such as RF Signal Generators, RF Synthesizers, RF Network Analyzers, RF Power Detectors, RF Mixers, and RF Frequency Converters. These devices can be used as RF Test and Measurement Equipment and controlled by Labview in an Automated Test Equipment (ATE) setup, or used as bolt-in RF modules in RF communications equipment. All products have innovative, powerful feature sets controlled by internal microprocessors so any settings can be memorized and used with or without a PC. Windfreak hardware also comes with the Labview GUI source code saving the end user hundreds of hours programming custom software.  Use one of our RF Signal Generators or other products risk free.  Return it if you dont like it.

  • Computed Tomography Equipment Technology for OEMs

    Computed Tomography (CT) - Analogic Corporation

    Integrated CT Systems – A more highly integrated system is the ideal solution for customized standalone CT and multi-modality applications. Our value-added integration capabilities provide our customers with a significantly reduced time to market. Scope of work is driven by specific customer requirements. PowerLink™ – Scalable, next-generation, non-contact power, control, and data transfer architecture. Provides practical advantages that include: Improved reliability Reduced maintenance Significant gantry space savings Enables dose reduction; dose modulation for cardiac applications; and kV modulation for dual-energy enhanced imaging applications. Data Management Systems – Advanced detectors + DASs (data acquisition systems) The brains of the CT system, the DMS converts X-ray energy to digital signals for image reconstruction. Our 16- and 64-slice DMSs provide our OEM customers with a higher level of system integration, reducing their costs and time to market. We also develop CT subsystems for innovative multi-modality applications, including radiotherapy and nuclear imaging.

  • Spectrometer

    ULSi - Avantes Inc.

    The same quality Avantes is well-known for, now in an easy-to-install package: the ULSi is the ideal choice for any system integrator. Fiber optic spectrometers have been integrated into many end-user systems in almost all areas of research and detection. Now Avantes releases its first completely integrated spectrometer: one housing including the optimum Ultra Low Straylight optical bench and a miniaturized version of our flexible AS5216 electronics board. The ULSi is available with the three best-selling detectors Avantes offers: the Sony ILX554B with 2048 pixels, the Sony ILX511 with 2048 high pixels for extra sensitivity and the Toshiba TCD1304 high resolution 3648 pixels. The same wide range of slits, gratings and other options available in the mainline spectroscopy lineup are also available for the ULSi.

  • Full Band Scalar Network Analyzer Extenders

    Sage Millimeter, Inc.

    Full band scalar network analyzer extenders are designed to extend low frequency scalar network analyzers to higher millimeterwave frequency ranges. These extenders offer a low cost means of producing millimeterwave scalar network analyzers while preserving the functionality and features that industry standard models offer. These extenders deliver a superior performance since they are assembled with SAGE Millimeter’s instrumentation grade frequency extenders (STE series), Faraday isolators (STF series), direct or programmable attenuators (STA series), directional couplers (SWD series) and waveguide detectors (STD series). The below standard offering covers the frequency range of 26.5 to 170 GHz. Specifications other than those listed below are available upon request.

  • Metal Detector

    Dor Yang precision instrument (Shanghai) Co.,Ltd

    1.Fully Automatic and All Metal Detectors - Your detector detects all kinds of metal objects. Unless you have set for some objects that you don’t want to detect.2.LCD – The LCD with light, it improve to identify the metal in night or caliginous outside. 3.Target Identity - The detected objects are shown on the LCD display. You can decide immediately if the objects worth to be recovered.4.Unwanted Target Elimination - You can set the detector not to respond to some objects.5.Unique Tone for Target - You don’t have to keep watching the LCD display, when an object is being detected, an unique tone corresponding to a target will generate. You may even searching when there is little or no light.6.No Clumsy Slack Cable - hidden search coil cable (connecting between control unit and search coil) avoid entangling and for ease of stem length adjustment.7.Headphone Jack - provided for headphone connection. Both stereo or mono headphone can be used.8.Volume Control - for adjusting the output volume to the loud speaker or headphone.9.Batteries Condition Indicator - shows the conditions of the batteries in the battery compartment.10.Waterproof Search Coil - lets you use the detector in the shallow water.11.Adjustable Stem - lets you adjust the detector’s length for comfortable use. The micro-plug that connects the search coil and the controller unit is made of metal which makes the plug more reliable.

  • Non Destructive Testing (NDT)

    Keighley Laboratories LTD

    NDT covers a wide group of testing techniques used to evaluate the properties of a material, part, product, weld or system without causing damage. NDT carried out at KLL includes:Liquid Penetrant Testing (LPT) is used for the detection of surface breaking discontinuities on magnetic and non-magnetic metallic materials.Fluorescent and colour contrast penetrants are available to be used in the following methods:-Water washableSolvent removablePost emulsifiableMagnetic Particle Inspection (MT/MPI) is used for the detection of surface breaking and slightly sub-surface (up to 2mm) discontinuities.Bench type crack detectors and portable units are employed producing various waveforms (i.e. A.C, HWDC and induced magnetic flow) to give both circular and longitudinal magnetism.On-site testing is carried out using electro magnetic yokes and permanent magnets producing induced magnetic flow.Ultrasonic Flaw Detection (UT), also known as Ultrasonic Inspection, is used for the detection of volumetric discontinuities in ferrous and non-ferrous products (forgings and castings etc.), and welds in magnetic and non-magnetic materials.UT is capable of penetrating metals, dependent on the material characteristics, up to 10m in length.Some thickness and depth checks can also be carried out using ultrasound.Radiography services are available through sub-contract booked in advance. Notice is required for on-site work.Personnel are available at short notice for in-house or on-site work in the UK and overseas.All inspectors undertaking non destructive testing (LPT, MT/MPI and UT) are qualified to, and meet a minimum of, PCN Level 2.PCN Level 3 supervision is available in-house for LPT, MT/MPI, UT offering consultancy services including procedure writing and commentary, auditing of techniques and Level 3 Supervisor cover.We can assist clients in product qualification, material testing, quality assurance and audit programmes.

  • Domestic Direct Reading Spectrometer

    CS-8610 - Wuxi Tianmu Instrument Technology Co., Ltd.

    1. Convenient, practical and reliable: unique combustion device, equipped with infrared detection system, direct connection, remote control operation.2 , patented burner design (using utility model patent technology)The burner electrode upgrading system adopts a spring structure, the electrode adjustment is convenient, and the double sealing ring guarantee the pressure balance in the furnace cavity without tempering.3 , to ensure accurate measurement results◆Using low-noise, high-sensitivity, high-stability pyroelectric infrared detectors.◆Specially-made new platinum infrared light source, continuous heating and high spectral efficiency.The modular design of the whole machine, the electronic circuit is highly integrated, which improves the reliability of the instrument.◆Industrial-grade integrated linear module power supply, stable output, no fault.◆The infrared detection part and the combustion furnace are connected by optical fiber, and cooperate with multi-level concealed isolation circuit to completely eliminate arc interference.◆Double filter device to reduce the impact of dust on the analysis results.4 , electronic balance is not quantitative sample: you can choose different brands of electronic balance, automatic online, to achieve non-quantitative weighing.