Showing results: 586 - 600 of 681 items found.
-
Electromechanica, Inc.
The rail inverter test system uses a pulse test methodology to verify proper operation of the IGBT switching elements in a subway car motor control. The system is designed to verify proper commutation of the switching elements. A large capacitor bank allows testing at DC voltages up to 1kV and peak currents of up to 3kA into reactive loads.The system also integrates self test capabilities and safe-to-turn-on (STTO) diagnostics to ensure no gross faults are present prior to the application of high voltages. Further the system includes dielectric withstand (hi-pot) test capability to ensure electrical safety.
-
Analog Devices Inc.
Analog Devices portfolio of leading industrial d/a converters and drivers addresses the challenges of enhancing system accuracy, reliability, and overall functionality while reducing form factor and power dissipation. The products provide a range of programmable output ranges from standard 4–20 mA for current loop communication to ±10 V for actuator control. They simplify industrial system design by offering considerable control functionality and advanced on-chip diagnostics to maximize system up time. ADI industrial converters also eliminate the need for costly calibration routines needed by some traditional discrete architectures.
-
PGK 80 -
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR PGK 80. The portable, one-piece PGK 80 high-voltage test device for generating negative DC voltage up to 80 kV is primarily used for onsite testing of paper-insulated mass-impregnated cables in the medium-voltage network. The high voltage is generated through a high-voltage transformer with secondary voltage-multiplier. The internal operating frequency of 20 kHz enables the smallest of device dimensions.* Continuous adjustable output voltage* The voltage measurement is done directly at the high voltage output* Timer of 1-30 min* Sensitive current measurement for recording the smallest of insulation currents with 6-time range switch, decadal
-
PGK 50 -
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR PGK 50. The portable, one-piece PGK 50 high-voltage test device for generating negative DC voltage up to 50 kV is primarily used for onsite testing of paper-insulated mass-impregnated cables in the medium-voltage network. The high voltage is generated through a high-voltage transformer with secondary voltage-multiplier. The internal operating frequency of 20 kHz enables the smallest of device dimensions.* Continuous adjustable output voltage* The voltage measurement is done directly at the high voltage output* Timer of 1-30 min* Sensitive current measurement for recording the smallest of insulation currents with 6-time range switch, decadal
-
Analog Devices Inc.
Analog Devices portfolio of leading industrial digital-to-analog converters address the challenges of enhancing system accuracy, reliability, and overall functionality while reducing form factor and power dissipation. The products provide a range of programmable output ranges from standard 4–20 mA for current loop communication to ±10 V for actuator control. They simplify industrial system design by offering considerable control functionality and advanced on-chip diagnostics to maximize system up time. ADI industrial converters also eliminate the need for costly calibration routines needed by some traditional discrete architectures.
-
Analog Devices Inc.
Analog Devices portfolio of leading industrial d/a converters and drivers addresses the challenges of enhancing system accuracy, reliability, and overall functionality while reducing form factor and power dissipation. The products provide a range of programmable output ranges from standard 4–20 mA for current loop communication to ±10 V for actuator control. They simplify industrial system design by offering considerable control functionality and advanced on-chip diagnostics to maximize system up time. ADI industrial converters also eliminate the need for costly calibration routines needed by some traditional discrete architectures.
-
JHPD-10 -
Xiamen Jiahua Electrical Technology Co.,Ltd
JHPD-10 quickly and accurately detects various kinds of partial discharge signals that occur with insulation defects in GIS. Attached on the surface of GIS the detector collects the inside discharge signal of impure gas, suspension potential and solid insulation material. The diagnostic software analyzes the fault character and locates the fault to avoid electricity accident. The device is for daily patrol inspection with high efficiency and easy operation features. Designed with two UHF signal channels, one detects the partial discharge signal; another excludes the disturbance signal like corona discharge in the air and mobile phone communication.
-
iPM -
North Atlantic Industries
NAI’s iPM is an Intelligent Power Monitor that provides a precise, instrument grade, digital analysis of input power lines. This advanced, DSP-based unit monitors single-phase, 3-phase 4-wire wye, or 3-phase Delta power lines at various input voltage levels and frequencies.The iPM is equipped with an EIA RS485-compatible serial communications interface that permits additional control functions and readout of diagnostic data, and features a Background Built-in-Test (BIT) that constantly monitors the health of unit hardware and software. This power monitor is designed and qualified to the most stringent performance and environmental requirements, and is ideally suited for rugged defense and industrial applications.
-
T-BERD/MTS-5882 -
Viavi Solutions Inc.
The T-BERD/MTS-5882 is extremely versatile, enabling the cell site technician to address all key tests with one, lightweight, handheld tester; including: Fiber Inspection: Dirty fiber connections are the #1 cause of network downtime. Microwave back-haul: The majority of microwave backhaul links around the world are still microwave. Enhanced Cable Diagnostics: Environmental factors can damage the CAT X shielded twisted pair cable connecting the microwave antenna. Fronthaul: Avoid dangerous tower climbs with CPRI testing including BERT, PIM detection, MIMO diversity, RET, and VSWR. Backhaul: In addition to packet testing across error-prone microwave hops.
-
Model GFC-7000T -
Teledyne Analytical Instruments
The GFC Series gas filter correlation analyzers measure low ranges of gases (CO2, CO2 and N2O detecting models available by comparing infrared energy absorbed by a sample to that absorbed by a reference according to Beer-Lambert Law. All GFC Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel or via RS-232, Ethernet or USBcom ports either locally or by remote connection using the included APIcom™ software.
-
Model GFC-7002T -
Teledyne Analytical Instruments
The GFC Series gas filter correlation analyzers measure low ranges of gases (CO, CO2 and N2O detecting models available by comparing infrared energy absorbed by a sample to that absorbed by a reference according to Beer-Lambert Law. All GFC Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel or via RS-232, Ethernet or USBcom ports either locally or by remote connection using the included APIcom™ software.
-
Model GFC-7001T -
Teledyne Analytical Instruments
The GFC Series gas filter correlation analyzers measure low ranges of gases (CO2, CO2 and N2O detecting models available by comparing infrared energy absorbed by a sample to that absorbed by a reference according to Beer-Lambert Law. All GFC Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel or via RS-232, Ethernet or USBcom ports either locally or by remote connection using the included APIcom™ software.
-
Watlow Electric Manufacturing Company
Watlow solid state power switching devices complement the rapid switching required by PID temperature controllers and help deliver optimum system performance and service life. They are available in 1-phase and 3-phase/2-leg and 3-leg configurations, feature touch-safe terminations, input indicators, zero-cross, random or phase-angle fire options, ratings from 18 to 1,000 amperes and agency approvals including CE and UL® 508. Various configurations offer short circuit current ratings (SCCR) of 200,000 amperes, extensive system and heater diagnostic capabilities, heater bake out, integrated heat sinks, on-board fuses, RoHS compliance and serial communications.
-
WesTest Engineering Corporation
WesTest Engineering Corporation offers turnkey test solutions for the military and aerospace sectors. Our engineering capabilities present an unmatched ability to take customer test requirements and design, developand integrate Test Program Sets (TPS) with diagnostics to the component level. This is further supported by a full complement of documentation, from Test Requirements Documents, to TPS Flowcharts, to Test Reports.With 36 years’ experience and 1000+ TPSs in our history, the WesTest Engineering Staff remains as one of the top notch senior staff’s in the TPS sector today. Our leadership and program management have the historicalexperience to lead WesTest capability to meet the customer’s requirement.
-
Response Dynamics Vibration Engineering, Inc.
Although strain measurement is often a key part of a root cause diagnosis, our analyses often also involve measurements of other parameters such as acceleration, relative displacement, pressure, temperature, flow, speed, load, dynamic stiffness, etc, to explore multiple parameters that may have a cause/effect relationship with the problem at hand. These measurements form part of a fact based hypothesis for the cause of the problem at hand. We use stain gauge testing and/or stain modeling and analysis, in conjunction with our structural dynamics expertise to characterize all the important pieces of the puzzle that come into play with dynamic strain issues (See Diagnostic Testing).
