Showing results: 316 - 330 of 533 items found.
-
RMO TD Series -
Amperis sl
The RMO-TD Series On-Load Tap & Winding Resistance Analyzer is designed for the measurement of winding resistance of inductive elements, and for tap changer analysis. The RMO-TD series is based on the latest technology, using the most advanced switching technology available today. The RMO-TD series is accurate (0.1%), powerful (up to 60 A) and lightweight. It generates true, ripple-free DC current with automatic metering control and a discharge circuit.
-
Bond-Rite CLAMP -
Newson Gale Inc.
In many branches of the process industries, fires and explosions can result from electrostatic discharge in hazardous areas. Even relatively small sparks have sufficient energy to ignite many flammable vapours, gases and even airborne dusts. In situations, where this risk exists, static grounding (earthing) and bonding clamps are required wherever mobile or portable conductive plant items (such as drums and vessels etc) are used.
-
EE15120A -
Executive Engineering
The EE15120A DC Electronic Load / Works @ 0.0 Volts Input & real time I/O control attach the electronic load block to a heat- sink and your up and running. used them with D to A's, A to D's, Pots, PLC's to control the current. These Electronic Loads can be used for both Discharge & Charging Batteries & Devices. The electronic load can act as a Current Regulator for charging
-
SONAPHONE® Pocket -
SONOTEC GmbH
With the SONAPHONE Pocket you identify problems even before they arise and create value at all levels of your company. Just by detecting and eliminating leaks you can reduce the energy costs for your compressed air system up to 30 percent. This also has positive effects on your operational safety and system productivity through early warning of bearing failure and evidence of partial electrical discharges.
-
Series 8500s -
Maccor, Inc.
The Series 8500s are high power fully automated test systems designed for testing and characterizing Electric Vehicle and Energy Storage batteries. The systems are designed with B2G technology, allowing the electrical energy produced during discharge to be recycled to the electrical grid.
-
Mess- & Prüfsysteme GmbH
The MSPS Software offers complete remote control of the partial discharge test set TPP.It is built ontop of a powerful database and offers the following possibilities. It is especially designed for use in a continious manufacturing test environment within a quality management system.
-
SL1007A -
Keysight Technologies
The SL1007A Scienlab Battery Test System – Cell Level enables you to accurately and productively test battery cells for automotive and industrial applications. The bidirectional power supply charges and discharges your cells under test with very high efficiency.
-
Novx MiniPulse -
SIMCO-ION, Technology Group
Simco-Ion's Novx MiniPulse ESD Event Detector is designed for tool and process monitoring. This affordable, small footprint embeddable monitor has been developed to warn of product damage risks at the point of electrostatic discharge. The MiniPulse uses time domain and threshold discrimination to detect pulse electromagnetic energy. Through the use of specific antenna configurations and placement, the MiniPulse can provide ESD event detection for well-defined small areas.
-
SFH166 -
Shanghai Launch Electric Co., Ltd.
Full automatic capacitance and inductance tester is specially designed for shunt reactor groups, single reactor in SCV equipment, under the instruction of reactive power compensation experts.Measure capacity of shunt capacitor, assembling single capacitor or group capacitors without removing the windingMeasure inductance of reactor and wave trapper without removing the windingMeasure run-in capacitance of transformers and generators without removing the windingMeasure shunt (discharge) resistance
-
LCV -
Bitrode, Inc.
Configurations for testing to industry standards: IEC, SAE, BCILife Cycle Testing: Perform charge/discharge cycling of batteries or modules to obtain charge and discharge capacity, energy and DC internal resistanceAutomotive Battery TestingStarting, Lighting and Ignition (SLI) TestingTraction Battery Testing
-
Koyo Electronics Industries co., ltd
The Coil Tester can measure the number of winding, layer short and core material by comparing vibration waveforms of the applied voltage to the standard coil and the test coil. This instrument also can find an insulation failure by applying high pulse voltage and checking the corona discharge.
-
ONYX16 -
Laplace Instruments Ltd.
The ONYX is a state of the art electrostatic discharge simulator available in 16kV or 30kV versions. It is the most ergonomic 30kV ESD gun without an additional base control unit that can be battery or mains operated. The easy to use touch screen, ergonomic design, modular RC units, multilingual interface, remote control software, built-in LED light and temperature & humidity display allows for trouble-free use of the ONYX in all types of test sites.
-
Techimp HQ S.r.L
Horn antenna is a partial discharge sensor designed to receive electromagnetic (EM) emissions from a PD occurring in electric assets like GIS and GIL or MV and HV power transformers. It is a broadband antenna with a flat response which makes Horn antenna suitable in a number of different applications. It has been optimized to operate in a frequency range suitable for PD activity monitoring and it was designed to provide maximum sensitivity and high gain.
-
LECO Corp.
Use LECO analytical instruments for chemical analysis and you'll discover why so many chemists worldwide trust us to help them deliver fast, accurate results. Innovative determinators for carbon, sulfur, hydrogen, nitrogen, and oxygen analyze organic and inorganic/metal samples, glow discharge spectrometers perform bulk and/or quantitative depth profile analysis, and analyzers precisely measure fat, protein, ash/moisture, mercury, and calorific value.
-
ULD-420 -
Amprobe Test Tools
When equipment begins to fail due to an air or gas leak or vibration, or electrical discharge, the leakage point emits an ultrasonic sound wave that is above the natural range of human hearing. The ULD-420 Ultrasonic Leak Detector converts this ultrasonic sound into a signal that can be used to pinpoint the exact location of the equipment failure. When working in unpressurized systems or the pressure is not sufficient enough to detect or verify a leak with the Receiver alone use the Transmitter.