Showing results: 1966 - 1980 of 3755 items found.
-
LS-44-QBS -
Lumistar Inc.
The LS-44-QBS contains up to 4 Lumistar LS-40-DB25 Bit Synchronizer Daughterboards in a 1U RackMount chassis with status lights on the front panel and all interconnections through the rear. The design contains an internal computer which runsoff DOS or Windows depending on the version selected. The DOS version boots quickly without the delays required for Windows startup. The Windows version offers networking. The unit can be connected directly to the optional 1U slideout keyboard/display, for setup resulting in only 2U of total rack height. For applications that require many bit synchronizers, a 1U keyboard/Display with KVM switch allows 32 bit synchronizers in 9U of rack height. When power is applied, the computer will operate with the last configuration unless the operator wishes to change the setup. For setup, the keyboard/display is pulled out and the display is flipped up to monitor the process. When the bit synchronizer setup is completed, the keyboard/display canbe closed up since the status can be monitored on the front panel without an external display.
-
DIT-915: -
Neutronics Manufacturing Co.
• A timer which shows the elapsed time when the test was "ON" and also shows the total time of the test• Displays a voltage warning and sound when AC or DC is present before injecting the test voltage.• A buzz will intermittently sound when high voltage is generated and continues until the circuit is fully discharged• Four voltages (1KV, 2.5KV, 5KV and 10KV)• Auto-ranging and menu-driven.• A bar-graph which displays the voltage decay during the discharge of the tested circuit and the voltage stressing the insulation while the test is in progress
-
WPM-19 -
Notice
•19λ CWDM Wavelength Meter– Auto λ detection for CWDM 19-wavelength– Auto power calibration & display•FTTx/PON Wavelength Meter– 1310/1490/1550nm auto λ detection– Auto power calibration & display•Optical Power Measurement– Optical network power measurement– Power measurement for system & module•Insertion Loss Measurement– Optical network & component IL measurement– IL measurement for CWDM 16-wavelength•Smartphone Interface– Communicates with smartphone via bluetooth– Smartphone application software
-
WPM-1NM -
Notice
•Wide range Wavelength Meter– Auto λ detection from 1270nm to 1610nm– Auto power calibration & display•FTTx/PON Wavelength Meter– 1310/1490/1550nm auto λ detection– Auto power calibration & display•Optical Power Measurement– Optical network power measurement– Power measurement for system & module•Insertion Loss Measurement– Optical network & component IL measurement– IL measurement for CWDM 16-wavelength•Smartphone Interface– Communicates with smartphone via bluetooth– Smartphone application software
-
DU2316/2317 -
Delta United Instrument Co., Ltd.
Leackage Current range display: 0.0001uA ~ 20.00mAAutomatic or Manual trigger with CHARGE/TEST/DISCHARGE100 sets of memory, can be saved test parameter and comparator setting, easy to use.Cover up free, system firmware upgrade can be update via RS-232, easy to maintenanceHi / Lo current limit setting & PASS/FAIL judgment240*64 Graphic LCD display, can be read the reading clearly and easier.User friendly programmable interface, easy to useProvided RS-232C and Handler combinatorial interface option, to meet your needed
-
CRY5620 -
Hangzhou JiGao Electroacoustical Science and Technology Co.,Ltd
CRY5620 microphone tester can test many types of microphones such as electret and MEMS. The instrument is controlled by a single-chip microcomputer, combined with digital analog processing technology. It integrates signal generation, signal processing and data display in one. It can display the sensitivity of the microphone at any three frequency points of the low frequency, intermediate frequency and high frequency, and the microphone current. The instrument is easy to operate, the setting interface is friendly, and the test is fast and accurate. Therefore, it is an ideal instrument for production lines, measurement departments and other units.
-
1160 IN -
Standard Electric Works Co., Ltd
● Measures insulation (MΩ), Continuity (Ω) and AC voltage.● Three insulation test voltages(DC V) : 250V, 500V, 1000V.● 3½ digital LCD (2000 counts).● 68 × 34mm ( 2.677” × 1.338” ) large LCD display.● LCD backlight display.● Automatic circuit discharge.● Test insulation at rated voltage into a 1mA load.● 200mA short circuit testing current for continuity.● Auto ranging.● Fuse protection.● Data hold function.● BS 16 edition.
-
KM 5410 -
Kusam Electrical Industries Limited
* Hand-pump with filter to isolate dirt and particles.* Thermocouple offset adjustment ±3°C (6°F).* Automatic power off battery saver.* 2 channel display(LCD).* Display Back-Light.* Analyzer Directly Measures: Flue Gas Oxygen Content in % and Flue Gas Temperature in °F or °C* Analyzer Computes: When the measured oxygen level is below 17.9%, Flue Gas Carbon Dioxide content in %, , Excess Air in %(0 to 400%), Flue Natural Gas/Oil #2/Propane in %
-
Eltel Industries
*For fast and accurate measurements of low resistance on Switch Contacts, SF-6 Switch Gear, Bushbars, Splices, Joints, Fuses, Breaker Contacts, and Rail Bonds.*100A DC continuous current in 4 ranges of 10A, 20A, 50A and 100A*4 1/2 digit display for higher resolution*Wide resistance range of 20µΩ to 200mΩ in 5 ranges*Suitable for operation in energized switchyard conditions*SMPS based- lightweight and portable
-
DisplayMate Technologies Corporation
DisplayMate Multimedia with Motion Bitmaps Edition includes a Motion Engine that moves a special set of test patterns and test photos to measure and evaluate response time, motion blur and motion artifacts in displays for different speeds, directions, intensities and colors for all monitors, projectors and HDTVs. It has everything in the standard Multimedia Edition including all of its 500+ test patterns up through 3072 x 3072 resolution.
-
DL Series -
Vitrek Corporation
Industry’s Easiest-To-Use DC Load – Vitrek’s DL Series Electronic Loads are available in a multiple configurations to meet your unique application requirements. No other electronic DC load on the market today is easier to use. Equipped with a full color LCD touchscreen display, the unit can quickly be set up for your next test. In addition, the DL is equipped with a comprehensive self-test that ensures that all loading and measurement circuitry is functioning properly.
-
ONYX16 -
Laplace Instruments Ltd.
The ONYX is a state of the art electrostatic discharge simulator available in 16kV or 30kV versions. It is the most ergonomic 30kV ESD gun without an additional base control unit that can be battery or mains operated. The easy to use touch screen, ergonomic design, modular RC units, multilingual interface, remote control software, built-in LED light and temperature & humidity display allows for trouble-free use of the ONYX in all types of test sites.
-
FLIR K55 -
Teledyne FLIR
With a FLIR K55 TIC in hand, you can attack fires more strategically, maneuver through smoke more easily, and save lives. The K55 displays crisp thermal images on a bright LCD, helping you navigate better and expedite critical decisions. The 320 x 240 pixel IR sensor and FSX™ Flexible Scene Enhancement produce detail-rich imagery at a 60 Hz frame rate that keeps up with the action.
-
NuVant EZware-EIS Software Package -
NuVant Systems, Inc.
The NuVant EZware-EIS software package activates Electrochemical Impedance Spectroscopy on the EZstat-Pro, Powerstat-05 and -20 potentiostat/galvanostats. EZware-EIS exports the impedance data to a file format to accommodate free third party EIS analysis software. EZware-EIS is a user-friendly interface that allows selection of the proper scanning parameters, collect the impedance spectra, display data in Nyquist and/or Bode plots and export data in the proper data format for use in EIS analysis software.
-
Data Explorer -
Losant IoT, Inc.
he Application Data Explorer allows you to easily explore, aggregate, and analyze historical data across all of the devices in an application. The data explorer can be accessed through the "Data Explorer" link in the Application navigation bar: control the time range, resolution, and aggregation of the data. determine what devices and attributes we are gathering data from. displays the data in various ways (in graph form, in table form, or in aggregation form)
