Showing results: 1591 - 1605 of 2502 items found.
-
LXinstruments GmbH
Manufacturers of electrical or electronic products are required by law to carry out an electrical safety test before placing them on the market. This final test takes place at the end of the manufacturing process and is therefore also referred to as an EOL test (end-of-line). Depending on the prescribed standard and directive, the following parameters are tested:- Leakage current and discharge current- Insulation resistance or the insulation strenth- Dielectric strength or electric strength- Correct installation of the protective conductor (ground continuity and ground bond test)- Faultless functioning of the product under the conditions defined for intended use (function or run test
-
22700 -
S & G Tool Aid Corp
Use to test for continuity with power disconnected. Excellent for use on marine, recreational and general automotive vehicles. Test appliances and other electrical circuits with power off. 48" lead wire. Uses AA 1.5 volt battery (not supplied).
-
PU260 -
Di-Log
Proving unit to enable compliance safety checking of voltage indicators for safe operation prior to testing on a live circuit.It is a requirement by Electrical Safety Council and the HSE that every electrician proves their voltage testers before confirming safe isolation.
-
Hilkar
Line Traps are used in transmission and distribution networks and they are the key components in Power Line Carrier (PLC) systems used for remote control signals, voice communication, remote metering and control between substations in the electrical T&D networks.
-
TEL1-x Series -
Standard Electric Works Co., Ltd
● The TEL1 is the Basic Test Equipment an Electrician cannot do without. TEL1 is a Dual Function Test Instrument utilized to Verify Electrical Wiring Connections and the Functioning of Earth Leakage / Residual Current Detectors devices by forcing the ELCB/RCD to trip.
-
LXinstruments GmbH
General functional test system based on LXI instrumentation for high mix / low to medium volume manufacturing. DUTs are tested which are mainly used as communication and measurement modules in power plant technology, grid management and electrical drives.
-
LXinstruments GmbH
General functional test system based on LXI instrumentation for high mix / low to medium volume manufacturing. DUTs are tested which are mainly used as communication and measurement modules in power plant technology, grid management and electrical drives.
-
Neutronics Manufacturing Co.
Oil Test is an equipment designed to test the dielectric strength of Insulating Oils as per relevant specifications vis. IS 6972. It is a useful equipment for Transformer / Switch Gear manufacturing units. Oil fettering agencies, repair shop and electrical maintenance departments.
-
HE-200H -
HORIBA, Ltd.
HE-200H connects conductivity sensor (FES-125F,126F) and measures conductivity and temperature in the sample water. It can be used not only for measurement of electrical conductivity in aqueous solution, but also for concentration adjustment and rinse monitoring of CIP, etc., as well as for concentration monitor of process.
-
DBT Series -
High Voltage Inc.
DBT Series benchtop models are ideal for testing medium and high voltage electrical components and apparatus requiring DC withstand testing or a DC current leakage measurement (hipot test). These products are housed in benchtop cabinets for industrial and commercial markets.
-
PMT3000 -
Power Measurement Technologies Inc.
The PMT3000 Digital Cable Phasing Meter facilitates the testing, maintenance and installation of electrical distribution systems. Voltage magnitude, phase angle, phase rotation, frequency and tap capacitance measurements are provided in one convenient battery powered hand-held instrument.
-
MO-100 -
Amprobe Test Tools
Diagnose potential failure with the MO-100, portable battery powered milliohm meter. Quickly check windings opens or shorts in motors, generators and transformers, wire-to-wire connection resistances, heating elements testing and contact resistance in critical electrical connections.
-
MFT5010 -
Summit
It can be used to test insulation resistance, continuity, loop impedance and RCCB, earth resistance tester, five major test requirement in the electrical testing industry. Phase indicator. Can check a wide range of 3-Phase Power source from 110V to 600V
-
Inspector 930 -
LITE-CHECK LLC.
The Inspector 930 trailer tester is a complete, all-in-one trailer diagnostic system which simplifies ABS, brakes, air, lights, and electrical testing. It provides the ability for a single technician to perform a full inspection in one trip around the trailer.
-
ACD-41PQ -
Amprobe Test Tools
The Amprobe ACD-41PQ provides a simple and effective way to verify if the electrical system is affected by harmonics. Add on troubleshooting capabilities with the ACD-40PQ data-logging feature or get complete power analysis with the ACD-41PQ. Increase measuring efficiency with an optional PC interface kit.