Filter Results By:
Products
Applications
Manufacturers
-
product
Electrical Testers
Regardless of what your trade requires, Klein Tools has an electrical tester for the job. With non-contact testers as well as outlet and receptacle testers, there’s guaranteed to be the tool for your jobsite needs. All Klein’s testers are engineered for ease of use and to stand up to the tough jobsite conditions encountered by professionals every day.
-
product
Electrical Testing
Innovative Testing Solutions, Inc.
Our specialty is Direct Current automotive components. We perform product validation and design verification testing on both electrical components and systems. Also, we perform warranty investigation testing and failure analysis. We have voltage capabilities to 300 volts and current capabilities to 1000 amperes. Both two-wire and four-wire resistance measurements are supported from NanoOhms to GigaOhms.
-
product
Electrical Tester
C.A 742
The C.A 742 Voltage Absence Tester is an essential tool for any electrician to check that no voltage is present before working on an electrical installation connected to the network. It complies with IEC 61243-3 Edition 3 and can be used to work on any indoor or outdoor 600 V CAT IV installation. To fulfil the requirements of the standards and legislation in certain countries, there are 2 references, with or without IP2X accessories.
-
product
Electrical Testers
Actron is an industry leader in electrical testers for your car or home repair projects. Pick your choice of Actron’s digital multimeters to help pinpoint problem areas and determine which components need repair or replacement. Find shorted and open wiring with the help of our circuit testers. Troubleshoot fuel injectors, solenoids, and digital sensors with the Actron Automotive Logic Tester. Use Actron IR thermometers to check AC systems, brakes, catalytic converters, cylinder heads, and overheating electrical components. Use the Actron Videoscope to inspect hard to reach areas. Measure and set spark plug timing on older vehicles, tractors, lawn mowers and more using Actron timing lights. Find bad batteries and faulty charging systems with Actron Battery Load Testers. Our Remote Starter Switches allow one person to conduct tests while cranking or starting the engine.
-
product
Rotating Electrical
Through its vast distribution network, WAI provides customers in the aftermarket with access to a wide range of product lines they need, when they need them. WAI’s production team is committed to consistently being the First-to-Market with the latest model products. This commitment, paired with the skill and expertise of the team, results in the introduction of more than 500 new products to the aftermarket each year. WAI offers 100 percent new alternators and starters as well as generators, motors, voltage regulators, rectifiers and other components for the Rotating Electrical market.
-
product
Electrical Laboratory
As one of North America’s largest and most diversified product testing and engineering service providers, Trialon provides a comprehensive range of EMI/EMC, ESD and Electrical testing solutions. Our EMC Testing Laboratory is ISO/IEC 17025 accredited, as well as being an approved facility for both General Motors and Ford Motor Company. Plus, we provide multi-shift support to assure programs meet time lines. Trialon’s EMC team has NARTE-certified personnel that will provide you with reliable and cost-effective testing that complies with a wide range of industry standards.
-
product
Electrical Tester
PRO T6-1000
The T6-1000 PRO Electrical Tester measures voltage up to 1000 V ac and current up to 200 A ac, all through the open fork and without test lead contact to live voltage. Connect the black lead to ground with the included heavy-duty alligator clip, slide the wire into the open fork and see both voltage and current at the same time. On wires up to AWG 4/0 (120 mm2), carrying as much as 200 A and 1000 V ac. Even with gloves on. It will change how you do your job.
-
product
Electrical Tester
T6-600
The electrical tester offers a variety of measurement options giving you an all-in-one troubleshooting tool. Measure true rms voltage and current from 0 to 200 A AC or 1 to 600 V AC or DC. You can also gather resistance measurement from 1 Ω to 2000 Ω. With the easy-to-read backlit display, you can keep see your work in dark environments and keep your most recent measurement on the screen with the HOLD button for easy viewing. The T6-600 also accepts optional Fluke TPAK Magnetic Meter Hanger for convenient operation.
-
product
Electrical Calibration
Process Instruments calibrates a wide variety of test and measurement equipment. All calibration procedures are written, and most are automated, insuring reliability and repeatability of measurements.
-
product
Electrical Indicators
Mitsubishi Electric Automation, Inc
Operation ease and viewable pursuing MITSUBISHI indicators.Pursuing accuracy,long life,easy-to-read scales, and monitoring the power supply or operational status of machine rapidly and accurately. MITSUBISHI indicators prepared suited model lineup in answer to diversified application needs.
-
product
Electrical Interface
QSFP-DD 200G
Eoptolink Technology Inc., Ltd.
QSFP-DD 200G Eoptolink’s EOLD-162HG-E-10-1 QSFP-DD CWDM4, 8x25G Optical transceiver module are designed for use in 200 Gigabit links over 10km singlemode fiber. They are compliant with the QSFP-DD MSA. Digital diagnostics functions are available via the I2C interface, as specified by the QSFP-DD MSA.
-
product
Electrical measurements
Instruments for measurement and analysis in accordance with the regulations of single / triphasic low voltage networks and data networks via cable or fibre.
-
product
Electrical Testers
The Fault Trapper is a new class of tester using Spread Spectrum Time Domain Reflectometry (SSTDR) to monitor energized circuits.
-
product
Electrical Testers
Digital voltage and continuity tester with LCD screenAC and DC voltage testing (7 thresholds) with automatic AC or DC detection, audible continuity and single-pole phase test.
-
product
Electrical Accessories
PENKOoffers a wide range of, instruments and controllers designed for highaccuracy, high speed weighing and dosing applications. A range of ancillary products are available, including power supplies, IO modules, cable extention boxes and printers. In addition to the products shown we offer addititonal suitable accessories for many applications.
-
product
Electrical Testers
Designed specifically for easy and intuitive use. After one minute, you’ll never again look at the directions. LCD displays exactly which measurement is being made. Audible beep confirms each measurement. Three distance memories and one calculation memory are maintained even when the unit is off. Calculator function permits addition/subtraction of readings.
-
product
Electrical Calibration
All calibrations include as Found/as Left data, Measurement Uncertainity, Calibration Sticker, Calibration Certificate and online access to calibration data at NO additional charge.
-
product
Electrical Calibration
GF6018A
Beijing GFUVE Electronics Co.,Ltd.
The equipment is compliance with national verification regulation: JJG1242005 "Ammeter, voltmeter, power meter and resistance meter verification rules" and related national standards. 0.05 single-phase AC/DC standard source, can verify magnitude 0.2 and the following AC/DC voltmeter, ammeter, frequency meter, resistance meter. The source signals by using DSP and 16-bit high-speed analog-to-digital converters of controllable sine wave, the distorted wave signal source.The equipment comes with RS-232 interface, can be connected with PC to a semi-automatic verification system. It has precise interface and multi-functions including verification, storage and query.The equipment adopts color LCD screen, chart character display is clear, with high precision, stable and reliable, convenient operation and flexible characteristics.
-
product
Electrical Tester
T+Pro
Safer than solenoid testers and fully compliant with NFPA 70E, (when used properly per Article 110.4 Use of Equipment (A) Test Instruments and Equipment), the T+Pro helps electricians and technicians work safer by indicating the presence of voltage, even when the batteries are dead.
-
product
Electrical Tester
VT12
No-contact phase detection• Extra-bright LED torch• operating voltage: 200V to 600V AC 50/60 Hz• IEC 61010 600V CAT III• Powered by 2 x AAA/LR03 batteries (supplied)
-
product
Electrical Testers
Precision Mastech Enterprises Co.
AC Voltage range: 50V-1000V AC, 50/60HzSafety standards: Designed to international safety standard IEC61010 - 1/600V CAT III, 1000V CAT II.Battery: 2*1.5V (AAA type)Altitude: <2000mOperating temperature: -10 to 50CStorage temperature: -20 to 60CHumidity: <85% relative humidityDimensions: 157*24*20 mmWeight: Approximately 42g
-
product
Electrical Tester
C.A 771
Compliant with IEC 61243-3, the C.A 771 VAT can be used to work on any 1,000 V CAT IV installation. It is rated IP65 and offers a type-S extended climatic class for indoor and outdoor use, including in extreme conditions.
-
product
Electrical Tester
C.A 757
The compact, lightweight C.A 757 tester is a test and measurement instrument offering all the essential functions required by electricians on a day-to-day basis.
-
product
Electrical Tester
VT14
12 V to 690 V voltage test (7 diodes)Indication of polarity by " + " and " – " diodesImpedance: 400 kΩOperating frequency: DC and 50/60 Hzovervoltage protection up to 1,000 VIEC 61010 600 V CAT IIIPowered by 1 x 9 V 6LR61 battery (supplied)
-
product
Electrical Tester
C.A 755
Lightweight and comfortable to handle, the C.A 755 is equipped with an IP 54 casing protected against dust and capable of withstanding falls from 2 metres. With its large 3,000-count backlit display, the C.A 755 tester is ergonomic and functional.
-
product
Electrical Design Software
AutoCAD Electrical
AutoCAD Electrical software includes all the functionality of familiar AutoCAD software, plus a complete set of electrical design CAD features.
-
product
Opto Electrical Slip Rings (Electrical and FORJ Combined)
Opto Electrical Slip Rings are a combination of fiber optic rotary joints (FORJ) with gold, silver or carbon contacts. High data rates are transmitted through the FORJ while power and other signals are transferred through a contact technology.
-
product
ELECTRICAL TEST Kit
1027 TK
Standard Electric Works Co., Ltd
1027 TK is an electrical technician's kit which provides the electrical testing needs for installation, plant maintenance and repair of electrical systems.
-
product
Electrical Current Sensors
Electrical current sensors detect the flow of current along an electrical wire by measuring (or sensing) the magnetic field that is generated by the flow of electrical current. The sensors output signals that are transmitted to dataloggers
-
product
Electrical Safety Analyzer
Guarantee the safe operation of your electrical equipment with Netech’s Electrical Safety Analyzers. We offer three versatile electrical testing tools which can be used for a variety of safety testing on devices including hospital equipment and patient monitoring equipment. Scroll down to see an overview of our electrical safety analyzer models.