Showing results: 796 - 810 of 2571 items found.
-
SE400 -
Gigasense
The Sharp Edge Tester is used for determining the sharpness of edges of electrical equipment and other consumer products. A special tape is mounted on a spring loaded arm and dragged over the sharp edge. The tape is then inspected for damages.
-
Kryoz Technologies BV
The CryoLab MSG is a desktop system where all the required hardware is fully integrated inside a small casing. All connections to and from the CryoLab MSG, both gas and electrical, are made using quick connects.
-
Labfacility Ltd.
Using the principle of electrical resistance, pin-type meters use the board as an element in a circuit by driving two pins or electrodes into it. This method works because moisture conducts electricity well and dry wood is an effective insulator.
-
Kyoritsu Electrical Instruments Works, Ltd.
The clamp on the device is simply placed around a live wire. This allows one to measure the current on a wire without interrupting the operation of the electrical appliance. A clamp meter uses digital technology to bring instantaneous readings.
-
SK-7720/SK-7722 -
Kaise Corporation
Up to 1000A AC/DC.Conductor dia. : Φ36mm max.True RMS.Dual measurement and display.(Two electrical elements can be measured together)Peak hold and MAX/MIN functions.Temperature Measurement.Dust proof and water resistant.Analog output terminal (SK-7722)
-
Shimadzu Corp.
Optical emission spectrometry involves applying electrical energy in the form of spark generated between an electrode and a metal sample, whereby the vaporized atoms are brought to a high energy state within a so-called "discharge plasma".
-
4664-IH -
TESEC, INC
The ULTRA P is a high performance production handler that provides thermal conditioning, full 6 DOF mechanical stimulus and an electrical ATE signal path for testing Micro-Electro-Mechanical Systems (MEMS) Accelerometers and Gyroscopes.
-
ULTRA P -
FocusTest, Inc.
The ULTRA P is a high performance production handler that provides thermal conditioning, full 6 DOF mechanical stimulus and an electrical ATE signal path for testing Micro-Electro-Mechanical Systems (MEMS) Accelerometers and Gyroscopes.
-
Verifier 1020G -
LITE-CHECK LLC.
The Verifier system identifies and trends before they become problems. With the LITE-CHECK cloud system, multiple shops within your organization will share Abs, Tire, Brake, Air, Electrical, Lights, and Status of the entire fleet.
-
Whitelegg Machines Ltd
A cost-effective, fully featured solution for testing the safety and function of a variety of electrical products. Designed for machine builders and OEMs, the Whitelegg GLP series is a simple to use fast and effective tool for benchtop or production testing.
-
HAOMAI Electric Test Equipment Co., Ltd.
IEC 61850 is an international standard defining communication protocols for intelligent electronic devices at electrical substations. It is a part of the International Electrotechnical Commission's (IEC) Technical Committee 57 reference architecture for electric power systems.
-
Schweitzer Engineering Laboratories, Inc.
Expand the I/O of SEL relays and communications processors, reduce copper in substations by transferring I/O from remote locations over fiber, and provide electrical isolation to avoid ground paths and induced noise and interference.
-
Santronics, Inc.
This sensor started it all! Our original handheld sensor detects 50-1000 volts AC and is designed for a CAT IV environment. Always ready for use, this sensor can prevent electrical shock and is non-reactive to static electricity.
-
W-IE-NE-R, Plein & Baus GmbH
VME is a high speed and high performance bus system with powerful interrupt management and multiprocessor capability. It was created by combining VERSA-bus electrical specifications (1979) with the Euro-card format resulting in the VME-bus Revision A - 1981 specification.
-
MS6D -
COMET SYSTEM, s.r.o.
Data loggers are designed for measuring, recording, evaluation and subsequent processing of input electrical signals, which are subject to relatively slow changes (> 1s). In conjunction with the appropriate sensors and transducers are suitable for monitoring physical quantities.