Showing results: 916 - 930 of 2555 items found.
-
Weice Testing Instrument Co.,Ltd.
IP Code, International Protection Marking, sometimes interpreted as Ingress Protection Marking, classifies and rates the degree of protection provided against intrusion (body parts such as hands and fingers), dust, accidental contact, and water by mechanical casings and electrical enclosures.
-
T5-1000 -
Fluke Corporation
Measure current up to 100 A without breaking the circuit with OpenJaw™ design. The T5-1000 Electrical Tester is a versatile troubleshooting tool to carry to every job site. Use it to check voltage, continuity, and current–all with one compact tool.
-
SCHILLER AUTOMATION GmbH & Co. KG
The USB 3.1 USB (10 GT/s) Type-C Electrical Test Fixture Set provides a worst case, ISI hardware channel for PHY’s. It is intended to assist companies in testing transmitter signal quality and receiver sensitivity for either hosts or peripherals.
-
SUG255 -
Lisun Electronics Inc.
The Impulse Withstand Voltage Tester (or High Voltage Surge Generator), it is according to IEC255-5, IEC60060, IEC60065, GB14711, GBT17215.301 and GBT17215.322. It is suitable for doing all kinds of electrical and electronic products (such as energy meter, household appliances, low voltage electrical appliances and small power motor) insulation performance test.
-
Ironwood Electronics
Ironwood Electronics Grypper Y contact is design to work with BGA devices with solder balls/bumps with no equator or small exposure where the standard Grypper cannot reliably hold on to the solder ball. The Y shape, working with the sliding lid, allows reliable contact and ensures device retention in high vibration application. Lower forces, <25 grams, makes insertion easier too and the less aggressive contacting allows 40+ insertions of the same device. The Sliding Lid can be configured to include heat sinking. The Y contact designs cover BGA devices from 0.35mm pitch and larger and the short electrical length has superior electrical performance.
-
Schaffner
Harmonic filters help to obtain compliance withinternational standards like e.g. IEEE 519-1992 or EN 61000-3-12, and with local utility codes. They reduce electrical andthermal stress upon the electrical infrastructure, eliminate the risk of harmonics-related reliability problems, and supportlong-term energy efficiency and cost savings. Ecosine passive filters are the industry standard for 6-pulse rectifiers andnon-regenerative motor drives to achieve the often specified level of < 5% THID. Ecosine active harmonic filters providelatest generation digital technology. With a response time of less than 300 µs an efficient harmonics mitigation, powerfactor correction, and load balancing is achieved in real time.
-
Electronic Specialties Inc.
An electrical testing tool that integrates a basic digital multimeter with a current sensor. Clamps measure current.
-
WeiMin Industrial Co., Ltd.
LED-501 is a single crystal packing tester. It can be utilized in electrical test.Two test results. Pass (GO) or fail (NG).Electrical Testing: Forward:VF Reverse:VZ,IRFour-wire measurement and contact resistance in case of deviation.Auto polarity identification and preheat function.Provide OPEN\SHORT count.Compatible mechanical interface.Connected with computer for measurement data collection.
-
UI-FT07 -
Unuo Instruments
Shoe Dielectric Resistance Tester, also named as shoe high voltage withstand tester, is used to test shoe sole and heel electrical insulation, to check shoe performance of voltage withstand and current leakage. It is to test safety shoe dielectric resistance ability (Electrical Hazard Testing) as mentioned in ASTM F2412.
-
Cal Test Electronics
A complete offering of the most desired electrical test clips and electronic test clips including alligator clips, miniature alligator clips, crocodile clips, battery clips, heavy duty clips, general purpose clips, telecom clips, and many more.
-
Mk7A -
EDMI Ltd.
Built on the advanced Atlas metering platform, the Mk7A is a single phase 2-element meter which integrates both a 100A UC3 compliant relay and 40A UC2 compliant load control relay which allows disconnection and reconnection of electrical services remotely.
-
Teledyne Marine Impulse
Waterproof, submersible electrical connectors rated up to 20,000 psi. Specifically designed for harsh environments, the GRE connectors from Teledyne Impulse are rugged and reliable connections for ROVs, AUVs, underwater instrumentation, and others areas of high pressure or extreme conditions.
-
HA100 -
Summit Technology, Inc.
The HA100 is a compact clamp-on current probe for smaller loads where compact size is important. Its measurement range is from 0.1 to 100 amps AC and is very small which is ideal for locking inside a crowded electrical panel during monitoring.
-
Cryogenic Ltd.
To perform measurements at or above room temperature, separate heated sample probes are offered for electrical or magnetic measurements. In normal operation, the CFMS has a continuous temperature range of 1.6 K to 400 K. With these inserts the range can be extended up to 1000 K.
-
MAG-RJJ-6.0 -
R&J Measurement
The computerized measuring system is designed for measure the dynamic magnetic properties of the soft magnetic materials e.g. oriented or not-oriented electrical sheet. The system provides the opportunity of a tabular and graphic presentation of the obtained data, which can be presented by means of monitor, printer or plotter.