Showing results: 481 - 495 of 974 items found.
-
ELMA Electronic, Inc.
Field proven and ready for service, access to real time information is critical in today's networks. Ethernet switches and Layer 3 routing engines from Elma have the successful track record in critical applications you can rely on. Whether in rugged defense applications, transportation logistics network or a telecom application, network centricity is the defacto paradigm in embedded systems, providing the speed, scalability, reliability and security necessary to get the job done.
-
76500 -
Hickok Inc.
Easy to use and saves time. Instantly verify an active or inactive ignition coil by simply placing the sensing tip near the coil while engine is cranking or running at idle. During normal operation, an ignition coil creates an open magnetic field each and every time the coil is energized. By placing the sensing tip of the tool near or against the ignition coil, a blue LED will illuminate each time a magnetic field is detected.
-
FTX-ONE-CS/RS -
HORIBA, Ltd.
The FTX-ONE offers a 5Hz sampling rate and simultaneously measure the concentrations of multiple components including NH3, CH4, and CO2, from (engine) direct exhaust gas using the Fourier Transform Infrared (FTIR) method in combination with multivariate analysis algorithm.
-
1646 -
Peaceful Thriving Enterprise Co Ltd
Check on 6, 12 and 24V systems. Quickly and safely test high and low voltages on all vehicle voltages, including computerized engine. High impedance to protect sensitive electronic sensors, microprocessors, electronic ignition components and air bags.
-
1647 -
Peaceful Thriving Enterprise Co Ltd
Check on 6, 12 and 24V systems. Quickly and safely tests high and low voltages on all vehicle voltages, including computerized engine. High impedance protects sensitive electronic sensors, microprocessors, electronic ignition components and air bags.
-
R90-11HT -
Computer Conversions Corporation
These resolvers are rated for reliable operation in predominantly especially hot temperature applications, having an operating temperature over a wide range of -67 to 400 degrees Fahrenheit. The robust proven High Temperature ratings makes these resolvers particularly well suited for especially high temperature environments as found in: oil industry deep hole drilling, jet engine guide vanes, turbine governors, steel processing and automated heat treating type applications.
-
avSCAN -
Avionica, Inc.
avSCAN has gained a growing worldwide following at airlines, militaries, airframe and engine OEM’s, repair stations, research groups, regulatory agencies, accident investigation boards, and educational institutions. Be in good company. avSCAN is so much more than a DFDR Data Ground Replay System. From its core architecture to its user interface and rich feature set, avSCAN has steadily grown to become the benchmark for flight data analysis.
-
DVIGear, Inc.
Converter/Scalers provide two essential functions. First, they convert the input signal from one format to another (e.g. analog VGA to digital HDMI). Second, they allow the user to select the resolution of the output signal for display on a flat screen display or projection system. In many cases the quality of the output signal from our Converter/Scalers will be better than what is possible using a direct input on the display because of the price/performance limitations of consumer scaling engines.
-
PTFM-1000V2 -
HORIBA, Ltd.
The Pitot Tube Flow Meter, PTFM-1000V2 is a standalone interface for measuring exhaust gas flow rate of combustion engines. The system uses the tried-and-tested pitot tube principle with high-frequency transducers to accurately measure highly pulsating exhaust flows with a sampling rate of 1kHz. This rapid capture rate ensures that any pulsations or exotic behaviour in an engine is measured, and the unique design of the PTFM pitot tube means reverse flows can be measured with the same guarantee of sensitivity. The interface can be run standalone with a laptop, or seamlessly integrated to run alongside an analyser system without adding any more steps to the test cycle process.
-
778572-14 -
NI
7-Channel, 40 A PXI Signal Insertion Switch Module—The PXI‑2514 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2514 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
-
778572-12 -
NI
7-Channel, 10 A PXI Signal Insertion Switch Module—The PXI‑2512 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2512 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
-
778572-10 -
NI
68-Channel, 2 A PXI Signal Insertion Switch Module—The PXI‑2510 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2510 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
-
NI
FlexRay Interface Devices provide two fully functional FlexRay interfaces, allowing an individual engine control unit (ECU) to be connected to the interface when other cold-start nodes are not available. You also can use the interfaces individually to connect two separate FlexRay networks while maintaining full performance on each interface. FlexRay Interface Devices work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
IndySoft Corporation
The IndySoft Calibration Management workflow offers a rich feature set to manage the entire lifecycle of your quality assets. With support for leading enterprise platforms it's perfect for deployment in the corner lab of a startup manufacturing facility or a multi-site international quality-driven operation. With the IndySoft exclusive process modeling engine, companies can re-configure the event-driven workflows with checkpoints, rule sets, and documentation at every point along the equipment path, ensuring assets are handled according to their exacting requirements.
-
NI
The Vehicle Multiprotocol Interface Device excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI-XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
