Showing results: 1966 - 1980 of 3680 items found.
-
King Design Industrial Co., Ltd.
*Equipment conforms to IEC61730 MST12 specification.*Pre- or post-round can be selected for control wiring connection.*With weights block’s positioning pin is removed before test; and is inserted in the rear positioning hole for the remaining time.*Equipped with rings at both front and rear end; used to connect a rope and control the driving direction.*Use replaceable special cutting chip.
-
Infinity Machine International Inc.
Compression Test Machines by Infinity Machine International Inc. - for applications such as: baby carriages and strollers durability tester, compressive strength testing machine, tensile testing machine, extrusion compression test equipment for small consumer electronics, paper bursting/crushing compressive strength testing machine, pneumatic springs compressive strength testing machine durability, and more.
-
VMU -
Astronics Corporation
Vibration Monitor Units (VMUs) from Astronics employ proven vibration analysis to predict the failure of fans and other rotating equipment on passenger and cargo aircraft. Accurate prediction allows maintenance to intervene before a failure can occur, eliminating the resulting smoke or smoke smell event that can result in costly flight delays, diversions, emergency landings, or cancellations.
-
777690-01 -
NI
24-Channel, 5 V, TTL/CMOS, 2.4 mA Digital I/O Device - The PCI-6503 uses a 24-bit programmable peripheral interface (PPI). Each interface is Plug and Play compatible and does not require a separate card manager for configuration. The PCI-6503 can interface to peripherals or other computers, and it can operate in either a unidirectional or bidirectional mode and handshake with peripheral equipment.
-
10898D -
Keysight Technologies
The 10898D 2-axis high-resolution laser axis board provides the same resolution as the Keysight 10897D high-resolution laser axis board with increased slew rates and reduced noise. The increased stage velocity limits and low noise compared to previous laser systems offer premium positioning repeatability and accuracy for advanced applications such as IC fabrication equipment.
-
SY2103 -
Hong Kong Songyang Industrial Ltd.
The new SY2103 series portable three phase phantom load stable power source, designed from new digital wave compound technology and according to International Standard, is newly intelligent equipment for energy meters. The equipment includes voltage/current source & standard meter, operated easily through front panel to preset directly all data of meter under test and test process.
-
Viola -
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR viola. The portable and powerful viola high-voltage testing and diagnostics device is used for cable and cable sheath testing of medium-voltage cables up to 35 kV and electrical equipment. Another function is insulation testing on electrical equipment.* High performance and compact* Precise and non-destructive determination of the cable condition* Easy and quick test setup* Automatic testing and diagnostic sequences
-
Banair
This test equipment will help manufacturers, trading standards, consumer bodies, CPSC, CPSIA laboratories and regulatory authorities to check that they meet the requirements of ASTM F963 - 08 Standard Consumer Safety Specification for Toy Safety and ISO 8124-1:2009 projectile Safety of Toys –Part 1:Safety aspects related to mechanical and physical properties. It may also be valuable for certain sports equipment and related tests.
-
T015-POE -
Tripp Lite
The T015-POE Network and PoE Tester consists of an emitter and a remote. Its functions include standard and non-standard PoE equipment detection, PoE power online test, network cable continuity test, DC power test and switch loopback test. It is a practical tool for technical personnel to use during installation and maintenance of security monitoring equipment, communications wiring, integrated wiring and other weak-current systems.
-
Diamond SA
OTDR measuring devices are used in various ways in fibre optic technology. They enable extensive characterisation of existing fibre optic cabling networks. The use of launch and receive fibres is advantageous when it comes to ensuring precise results evaluations. With bidirectional backscatter measurements with launch and receive fibres, the attenuation values of the first and last plug-in connection can be determined precisely by averaging and device dead zones can be avoided. Measuring device manufacturers recommend different lengths of launch and receives fibres to avoid “phantom reflections”. These launch and receive fibres are also subject to measuring equipment monitoring and should regularly undergo revision in accordance with the OTDR measuring devices. A good measurement result depends on the state and quality of the measuring equipment used. Diamond offers various types of launch and receive fibres, one with standard telecommunications connectors and the other with an outdoor connector for harsh environments.
-
Applied Image, Inc.
The UPC Verification Calibration standards are a unique set of symbols that assures an exact and reliable primary bar code standard exists for UPC codes based on ANSI X3.182/ISO 15416 methodology. These standards assures that manufactures of verification equipment, scanners, QC labs and end users now have an accurate basis for checking the measurement capabilities of their equipment. These standards are intended as a fundamental calibration tool for an QC program, providing a continuous scale from best to worse case characteristics of each parameter. With complete NIST traceable data supplied, it is ideally suited to those requiring traceability, such as ISO certification. Each symbol is individually calibrated to ANSI X3.182/ISO 15416 standards using a custom built microdensitometer. These cards are supplied calibrated for use with a 6 mil scan aperture and 660nm wavelength. (calibration wit other aperture sizes or wavelengths is available)
-
PEC N.V.
PEC is the worldwide leader in cell, module and pack test equipment for advanced batteries and energy storage systems. Our test equipment combines very high control and measurement accuracy with an excellent dynamic behavior. This results in very precise, near real time simulations of demanding applications in electro-mobility, renewable energy, aerospace and defense. PEC also supplies test systems for primary batteries and consumer applications.
-
FT3151 -
HIOKI E.E. Corp
Earthing or grounding of electrical equipment is essential to maintain safety, protecting lives, as well as prevent damage to equipment. • Three-electrode method, Two-electrode method (Simple Measurement) • Wide measurement range for 0 to 1150 Ω, based on EN standard •Switchable measurement frequency to reduce the effects of power supply harmonics • Dramatically faster setup: Comes with improved grounding rods and cord winders. CAT II 300 V
-
AMETEK Sensors, Test & Calibration
Our configuration software provides a quick and easy way to customize your AMETEK equipment to fit your specific needs. Remove unused pressure units, add custom units, add task specific modes, disable buttons, password protect, download recorded runs, set logging intervals, remove and reorder display screens, and much more.
-
MI-2550e -
MEGABRAS srl
The MI-2550e general purposes megohmmeter is a truly portable equipment suitable to measure insulation resistances using test voltages up to 2,5 kV. It employs high-reliable, state-of-the-art technology for accurate measurements of ultra high insulation resistances up to 5.000.000 MΩ with four test voltages: 0,5 kV - 1 kV - 1,5 kV - 2,5 kV.
