Showing results: 511 - 525 of 989 items found.
-
COMBI519 -
HT Italia Srl
COMBI519 carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type B, A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
COMBI521 -
HT Italia Srl
COMBI521 carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type B, A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
EASYTEST -
HT Italia Srl
EASYTEST carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
DtifEasy Series -
Marvin Test Solutions, Inc.
DtifEasy is a full-featured tool set for importing, converting, and executing IEEE-1445 compliant digital test vectors generated by a LASAR simulation. All four IEEE-1445 file types - UUT model group, Stimulus and Response group, Fault Dictionary group, and Probe group are supported by DtifEasy; providing the user with the ability to execute go/no-go, fault dictionary, and guided probe sequences. DtifEasy supports MTS' 3U PXI GX529x series of dynamic digital instrumentation to 200 MHZ as well as the 6U PXI GX5960, 50 MHz digital instrumentation. All of these instrument families are compatible with the digital logic probe.
-
JHPD-10 -
Xiamen Jiahua Electrical Technology Co.,Ltd
JHPD-10 quickly and accurately detects various kinds of partial discharge signals that occur with insulation defects in GIS. Attached on the surface of GIS the detector collects the inside discharge signal of impure gas, suspension potential and solid insulation material. The diagnostic software analyzes the fault character and locates the fault to avoid electricity accident. The device is for daily patrol inspection with high efficiency and easy operation features. Designed with two UHF signal channels, one detects the partial discharge signal; another excludes the disturbance signal like corona discharge in the air and mobile phone communication.
-
779313-01 -
NI
16-Channel, ±30 VDC, 8 Sink/Source Inputs, 8 Relay Outputs, Isolated PXI Digital I/O Module—The PXI‑6521 is an industrial digital I/O module with high channel isolation and industry-standard 24 V logic levels. For added safety, the PXI‑6521 requires a keyed connector. If a computer or application fault occurs, the PXI‑6521 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. It also features programmable power-up states, digital filtering, and change detection for optimal control over your application.
-
CALEX
The 4:1 Input Voltage 75 Watt WDE includes remote sensing, ultra-wide output voltage trim, and remote ON/ OFF. The digital power management enables increased reliability, configurability, voltage / current precision and fault management.
-
EOFL-C -
Teledyne Marine ODI
Optical Extended CAN Bus Jumper, using fault tolerant to optical conversion to extend the range, can extend up to 5 kilometers subsea.Qualified repeater housing protected on each side by highly reliable glass to metal sealed penetrators.
-
Schweitzer Engineering Laboratories, Inc.
SEL transmission protection solutions provide complete primary and backup protection from all types of faults. Using these devices helps you avoid expensive equipment damage and failure while maintaining system performance and increasing availability.
-
Schweitzer Engineering Laboratories, Inc.
SEL distribution protection solutions provide complete primary and backup protection from all types of faults. Using these devices helps you avoid expensive equipment damage and failure while maintaining system performance and increasing availability.
-
Schweitzer Engineering Laboratories, Inc.
SEL generator protection solutions provide complete primary and backup protection from all types of faults. Using these devices helps you avoid expensive equipment damage and failure while maintaining system performance and increasing availability.
-
AUTO DIAGNOSTECH LTD
The probe can be used in 12/24 volt system with ECM/ECU either independently or used together with a diagnostic scanner to distinguish faults that lie in the sensor itself or the connection wires. The simulated voltage is used to emulate signals generated by different types of sensors.
-
ISM-200 -
Kongter Test & Measurement Co., Limited
ISM-200 Insulation monitoring system is a high accurate and secure online monitoring equipment for DC system insulation. It is designed for the measurement of different types of ground fault, insulation decreasing, AC signal interruption, DC signal interruption and so on.
-
CodeDynamics -
Rogue Wave Software Inc.
CodeDynamics provides faster fault isolation, advanced thread debugging, and powerful reverse debugging for your enterprise applications. CodeDynamics is an easy to use and intuitive dynamic analysis tool for inspecting, debugging, and fixing your C and C++ applications.
-
HVNCVT-1 -
Klein Tools, Inc.
Use to check for the presence of voltage in overhead conductors or find faults in cables.LOW range for 50V AC to 1.5kV AC.HIGH range for 1.5kV AC to 132kV AC.Audible and visual signals indicate the presence of voltage.Water resistant.Includes durable carrying case.