Showing results: 751 - 765 of 997 items found.
-
NCT-100-S -
ShinewayTech
*NCT-100-S Multi-Function Cable Tester Kit can help you quickly find network cables with OOK audio during network construction and maintenance. *Use TDR diagnostic technology to quickly and accurately locate fault points and accurately measure wiring diagrams and lines. Cable identification, etc.
-
KI2724-INGAAS-APC -
Kingfisher International
A SM & MM Quad Optical Loss Test Set used to test power, insertion loss, continuity and faults on multimode and single mode fiber with an APC connector at 850 / 1300 nm & 1310 / 1550 nm. In a small package, it provides a powerful solution to improve test flexibility and productivity.
-
Greenlee Tools
*Dual stick MARK series measure voltage and perform phasing operations from 0V to 75kV*No batteries or calibration required*Determines in-phase or out-of-phase*Determines underground cable faults*Discharges underground cables and other equipment that hold capacitive charges*Versatile for overhead and underground applications
-
SpectraQuest, Inc.
VibraQuest is an integrated data acquisition and analysis solution package designed for diagnosing rotating/reciprocating machinery malfunctions, structural dynamics analysis and acoustical analysis. This novel software includes proprietary advanced signal processing algorithms specially designed for diagnosing faults in drivetrain components such as gearbox, bearings and rotor cracks.
-
Mors Smitt Group
The transducers are based on compensating the magnetic field by a closed loop system. Ensure high accuracy of voltage and current measuring in railway traction or substation power equipment for protetion against power surges, overload, ground fault detection. Hall effect measurement to offer maximum protection in railway applications.
-
NI
PXI Signal Insertion Switch Modules, also known as fault insertion units (FIUs), provide a set of feedthrough channels, which make the switch transparent to the system when closed. You can open or short these channels to one of two fault buses, allowing you to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI Signal Insertion Switch Module can validate the integrity of control systems including engine control units (ECUs) and full authority digital engine controls (FADECs). You can also use the FIU models for hardware-in-the-loop (HIL) applications and electronic reliability tests.
-
G4103 -
Gunson
Suitable for use on all petrol engines and easily fits to most vehicles. Accurately measures pressures within the range minus 1 bar (30mHg) to plus 0.7 bar (10psi). Applications include: Engine Fault Finding, by using the gauge as an inlet manifold vacuum tester the following faults can be diagnosed: spark misfires, poor engine compression, mixture tool weak or too rich, ignition too advanced or too retarded, inlet manifold and carburettor air leaks, incorrect valve timing. Turbo boost gauge; testing boost pressure up to 0.7bar (10psi) and Petrol Pump Tester; tests electrical and mechanical petrol pumps (excluding high pressure pumps used on fuel injection engines)
-
PeakTech Prüf- und Messtechnik GmbH
The PeakTech 2710 is a residual current tester, which is used to determine tripping currents and the tripping times of residual current circuit breakers, which are used in every new building according to current building regulations. Residual current circuit breakers are used for personal protection and switch off a circuit when a residual current is registered which flows off via the protective earth (PE). RCD testers let a fault current flow and thus determine at which fault current the RCD triggers. The tripping time is also measured. These two parameters, tripping current and tripping time, are the safety-relevant parameters of an RCD. The various selectable test currents and characteristics that can be set with this device make the PeakTech 2710 the ideal companion for every electrician.
-
778858-01 -
NI
96-Channel, 5 V, TTL/CMOS, 24 mA PXI Digital I/O Module—The PXI‑6509 can directly drive external digital devices such as solid-state relays (SSRs). You can configure each port for input or output, and no external power supply is required for outputs. Using programmable power-up states, you can configure the initial output states in software to ensure glitch-free, safe operations when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6509 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
779949-01 -
NI
48-Channel, Sink/Source Inputs, Channel-Channel Isolated PXI Digital I/O Module—The PXI‑6529 is an industrial, parallel digital input interface. PXI‑6529 devices are ideal for a variety of applications from automotive design, industrial factory automation, and machine control to aerospace, laboratory research, and biomedical applications. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6529 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
eloZ1-400 -
elowerk Testsystems
The eloZ1 Manufacturing Defects Analyzer is an in-circuit tester of the very latest generation, reliably detecting connection and assembly faults on printed circuit board assemblies. The eloZ1-400 is the compact version of the eloZ1. It is particularly suitable if there is only limited space to fit test appliances. The eloZ1-400 can also be used as a mobile test system.
-
KI27624-INGAAS -
Kingfisher International
A Quad Optical Loss Test Set used to test power, insertion loss, continuity and faults on multimode and single mode fiber optic systems at 850 / 1300 nm & 1310 / 1550 nm. In a small package, it provides a powerful optical multi-meter style solution to improve test flexibility and productivity.
-
FiberPal OT-8800 -
Radiantech, Inc.
OT-8800 series instruments are compact, cost-effective, portable and high dynamic range Mini Optical Time Domain Reflectometer (OTDR). By providing all the measurement functions and performance required for optical fiber construction and maintenance, it is designed for full-range fibre fault detection to solve FTTx, CATV and optical LANs problems
-
Baseline 9400 TDR/ICE -
K&S Engineering and Scientific Ltd
BASELINE 9400 TDR/ICE - the unique cable diagnostic system: - A state-of-the art cable fault locating instrument containing a high speed data recorder, capable of capturing and evaluating 40 million samples of electrical data per second, while also featuring amplifiers, attenuators and an adjustable pulse generator.
-
PFMonitor -
DIgSILENT GmbH
The PowerFactory Monitor (PFM) is multi-functional Dynamic System Monitor which fully integrates with DIgSILENT PowerFactory software. The PFM features grid and plant monitoring, fault recording, grid characteristics analysis by offering easy access to recorded data, analysis of trends, verification of system upset responses and test results.
