Showing results: 121 - 135 of 136 items found.
-
N844-LOOP-12F -
Tripp Lite
Tripp Lite N844-LOOP-12F MTP / MPO OM3 Fiber Optic Loopback Tester is typically used for test and measurement procedures in networking environments. The device is ideal for a multitude of applications that require signal looping in a MTP / MPO form factor. Features push-pull tab for easy disconnect. A dust cap is included for protection during storage.
-
NEO TELE-TRONIX PVT. LTD
We are renowned as the foremost manufacturer and exporter of High Voltage Impulse Test Set Up. This testing equipment is demanded in electrical, power generation and engineering sector. It is incorporated with fiber optic isolated digitizers to test various types of transformers. We utilize excellent grade raw materials to engineer and develop this High Voltage Impulse Test Set Up in accordance with industry standards. Our clients can get this equipment from us at competitive price.
-
Radio Frequency Systems
RFS’ CPRI Interface Panels are used to test fiber connectivity between Optical Base Band Units (BBU) and Remote Radio Heads (RRH), allowing cell operations and system performance engineers to ensure the best performance without having to disconnect the fiber optical system or disrupt service. In addition, the CPRI panel enables easy RF over CPRI testing at the bottom of the tower, reducing the need for unnecessary tower climbs, thus minimizing maintenance cost and overall OPEX for customers. The RFS CPRI panel is bundled with RFS’ high-quality fiber optic jumpers, providing an end-to-end solution that includes HYBRIFLEX® fiber-to-the-antenna DC and F/O solutions.
-
Tessolve Services Pvt. Ltd
Tessolve provide Test & Product engineering Solutions & services from simple Logic ICs, high-speed digital, RF, Analog, PMIC, Mixed-signal, MCU/MPU, MEMS, Image Sensors, Memory to complex devices like ASIC/ASSP, SoC / SiP devices that go into Automotive, IoT, Wearable, Wireless, Computing, Network / Fiber optics and other consumer markets. We also engage ourselves in providing test solutions for emerging technologies in the 2.5D / 3D space.
-
Wuhan Sunma Technology Co., Ltd.
Optical Multimeter integrates both an optical power meter module and an optical light source module and can perform closed-loop tests by using both modules but work individually. It is specifically designed for technical support personnel to test a variety of instruments with a single meter and thus satisfy the user by providing a choice of greater convenience and more advantages. Contact us at Sales@SunmaFiber.com Buy other fiber optic products on SunmaFiber. Save your money & time right now!
-
CertiFiber -
Fluke Networks
The CertiFiber Pro Optical Loss Test Set improves the efficiency of fiber optics certification. The Taptive user interface simplifies set-up, eliminates errors and speeds troubleshooting. A set reference wizard ensures correct reference setting and eliminates negative loss errors. Built on the future-ready Versiv platform, CertiFiber Pro Optical Loss Test Set (OLTS) provides merged Tier 1 (Basic) / Tier 2 (Extended) testing and reporting when paired with OptiFiber Pro module.
-
OptiConcepts
The USB Connector Inspection System features easy focusing with high resolution imaging. The system includes standard software that provides image display, image capture, digital zoom, auto calibration, and basic analysis tools. Pass/Fail analysis and reporting features are optional software features. The Inspection System scope is fully compatible with the FiberWarrior Pro OTDR as well as other FiberWarrior Pro test sets, providing a full fiber optic testing solution.
-
STC-BTOPM2101-M -
Shanghai Stone Communication tech Co., Ltd
This multi-channel bench-top power meter is the high precision and wide measurement range test instrument. Which have intelligent micro processing control, and auto-shift of measurement range. This equipment have 8 laniary processing, which can avoid the difference caused by the non-laniary effect in different wavelength, and output power. And this will make the equipment much more stable and reliable in operation. With features of accurate measurements, durable use and easy operation, It becomes a perfect test equipment in fiber optic works which can instead the advanced imported products with its high cost-performance ratio.
-
FO-1553 -
Avionics Interface Technologies
Extends MIL-STD-1553 bus access to over 1 mile for remote access - Dual redundant, single and dual stream options available - Both Transformer and Direct coupling modes supported - Uses fiber optic 1.0625 Gbps data rates for low latency over long distances - Optical signaling is not affected by electrical noise and interference - Simple and easy to use solution, no software setup or configuration required - Ideal for applications where test equipment is separated from UUT
-
EV-SFP-171 -
UC Instruments, Corp.
The purpose of this SFP+ evaluation board is to provide the designer with a convenient means for evaluating SFP+ fiber optic transceiver such as 10 Gb/s(up to 16 Gb/s) SFP/SFP+ transceiver compliant with ANSI Fibre Channel FC‐PI‐5 for high speed electrical and optical specifications. This board provides SMA connectors for high speed TX and RX signals. The low speed control signals such as Tx_Fault, Rx_LOS and Rate_Selects can be controlled by using on board switches and test points. A connector for 2 wire serial interface to the module is also provided.
-
3621 -
Peaceful Thriving Enterprise Co Ltd
*Kit packs in a deluxe molded plastic case.*Set includes: 8 Noid lights for testing GM PFI, FORD TBI, GEO TBI, BOSCH PFI, GM TBI, GM SCPI, GM MULTEC 2 and BOSCH 2.*One IAC signal test lights for GM TBI and PFI fuel injection system, and one for GM Model 1987 or newer GM Model 700 TBI and PFI fuel injection system. Plus one fiber optic Noid Light extension.
-
B-1027 -
ROSS ENGINEERING CORPORATION
Ross Engineering Corporation’s High Voltage Calibration Lab provides high accuracy capability for conducting tough reliability tests on all our high voltage devices. In this facility we test and calibrate HV Relays, HV Dividers, HV Probes, Spark Gaps, our Fiber Optic Systems, and HV Digital Voltmeters up to 450kV. We provide our own in house test lab to ensure Ross products meet or exceed required safety standards as well as our own high standards of dependability, long life and quality. Our technicians use test equipment calibrated by or traceable to National Institute of Standards and Technology or other national metrology institute to provide the highest in testing accuracy.
-
ARINC 664 -
Avionics Interface Technologies
AIT’s ARINC 664 test instruments can be used in test and simulation applications that are required to transmit and receive data over the ARINC 664 avionics databus. AIT’s instruments use small form-factor pluggable transceivers (SFP) and support copper or fiber optic physical network interfaces.Using an FPGA based architecture, with multiple embedded processors, the ARINC 664 instruments provide onboard support for upper layer protocol processing (A653, UDP, IP) and utilize DMA to provide optimal data throughput. All ARINC 664 protocol operations, including VL traffic shaping, redundancy management, and IP fragmentation and reassembly, are handled onboard.
-
KI6512 -
Kingfisher International
KI6512 is an easy and economical handheld 100GBASE LR4/ER4 Wavelength Selective Power Meter for testing multi-λ single mode fiber optic systems. It scans and stores the absolute or relative power levels of all 4 channels in 0.8 seconds. Test data can be viewed in graphical or numerical form, and reference values can be stored for easy loss testing. An extra 50/125u power meter port gives additional flexibility at 850 / 1300 / 1550 nm. This port only supports basic functions, but is very handy for first-in fault finding and investigation.
-
LANTEK III Series -
IDEAL NETWORKS
New permanent link adapter saves money. Send test data anywhere using IDEAL AnyWARE app. Certifies multimode and single-mode fibre (optional). Professional PDF reports with free software. Certifies twisted pair cabling to TIA/ISO standards. The LanTEK III is an easy to use cable certifier that meets existing TIA and ISO/IEC performance requirements for testing up to Cat 7A/1000MHz. FiberTEK III adapters are used with LanTEK III for fast and simple certification of high bandwidth single-mode and multimode fiber optic cabling including support for encircled flux testing.