Showing results: 676 - 690 of 1081 items found.
-
PCI-9111 Series -
ADLINK Technology Inc.
ADLINK PCI-9111 series are 16-CH, 100 kS/s low cost multi-function DAQ card. The PCI-9111 series feature flexible configurations on analog inputs. A RC filter is implemented on each A/D input channel for user to attenuate or filter input signal. The PCI-9111 series provide analog inputs with 5 programmable input ranges for bipolar inputs. The PCI-9111 series also support automatic analog input scanning. PCI-9111DG provides 12-bit A/D resolution while PCI-9111HR provides 16-bit A/D resolution. The PCI-9111 series also feature 1-CH 12-bit analog output, 16-CH TTL digital inputs and 16-CH TTL digital outputs. ADLINK PCI-9111 series deliver cost-effective and reliable data acquisition capabilities, and is ideal for a broad variety of applications.
-
785989-01 -
NI
50 kS/s/ch, ±20 mA, 24-Bit, 8-Channel C Series Current Input Module - The NI-9253 is an 8-channel analog input module for ComapctDAQ and CompactRIO systems. Each channel provides a ±20 mA input range and 24 bits of resolution at a 50 kS/s sample rate. The NI-9253 has several diagnostic features to ensure your system is operating nominally at all times with open channel detection, power supply detection, and configurable thresholds. The NI-9253 has eight LEDs to indicate the status of each channel and the power supply so that a user in the field can easily validate that the system is operating normally. The NI-9253 also features a number of programmable hardware filters. By choosing the specific Butterworth and comb filters for your application, you can significantly reduce the noise in your system.
-
785989-02 -
NI
50 kS/s/ch, ±20 mA, 24-Bit, 8-Channel C Series Current Input Module - The NI-9253 is an 8-channel analog input module for ComapctDAQ and CompactRIO systems. Each channel provides a ±20 mA input range and 24 bits of resolution at a 50 kS/s sample rate. The NI-9253 has several diagnostic features to ensure your system is operating nominally at all times with open channel detection, power supply detection, and configurable thresholds. The NI-9253 has eight LEDs to indicate the status of each channel and the power supply so that a user in the field can easily validate that the system is operating normally. The NI-9253 also features a number of programmable hardware filters. By choosing the specific Butterworth and comb filters for your application, you can significantly reduce the noise in your system.
-
cPCIS-P2630R -
ADLINK Technology Inc.
*3U CompactPCI PlusIO backplane with five CompactPCI and four CPCI-S.0 peripheral slots and one system slot*Temperature, voltage, and fan monitoring LEDs*Supports rear I/O backplane with P2 connectors for CompactPCI 50mm depth RTMs*Hot-swappable cooling fans & filter*400 W ATX Power supply
-
Extech 401025 -
Extech Instruments Corporation
401025 is a Foot Candle/Lux Meter which measures light level to 5000FC (foot-candles) and 50,000 Lux with a 5% accuracy using a precision photo diode and color correction filter. Meter features fast/slow response time and an analog output (1mV per count) for capturing readings to a recorder. Comes complete with 9-Volt battery.
-
Pulse Electronics
Pulse’s complete offering of LTCC based Band Pass Filters, Balun’s, Diplexer’s and Couplers used in conjunction with our wireless antenna products will enhance your devices performance keeping attenuation and noise to a minimum. Many of Pulse’s IPD components are already qualified or referenced on various radio designs, so please contact us about the components already qualified on the radio you are using. From Wifi Networking devices, to smart phones and tablets, Pulse’s offering of IPD Components has you completely covered. Using the table below you can search our complete IPD Component offering.
-
NEX QC MFA -
Applied Rigaku Technologies, Inc
Specifically designed for marine fuel applications, the new Rigaku NEX QC MFA features an intuitive "icon-driven" touch screen interface for easy operation and a built-in printer for convenience. The shuttered 50 kV X-ray tube and Peltier cooled semiconductor detector deliver exceptional short-term repeatability and long-term reproducibility with excellent element peak resolution. This high voltage capability (50 kV), along with multiple automated X-ray tube filters, provides an analysis of sulfur (S), nickel (N), vanadium (V), iron (Fe) and zinc (Zn) ... all with low limits-of-detection (LOD).
-
44500 -
M. C. Miller Company
Rugged, lightweight case - safe to use on wet ground• Weatherproof, even with lid removed - IP67 rating for dust and water intrusion• Convenient case lid removal for ease of movement, with test leads attached, to new measurement locations• Resistance measurement range from 0.01Ω to 1.1MΩ • Resistance measurements are unaffected by any stray interference signals that may be present in the earth during readings, due to the use of narrow band-pass filters centered at 97Hz (the unit’s operating frequency)• Runs on a set of C-cell alkaline batteries...no need to periodically recharge the unit or to plug it into a power source
-
VRT2 -
Lectrosonics, Inc.
Up to six VRT2 modules may be installed per each 1RU Venue 2 receiver frame. Each module supports up to 3072 tunable frequencies across a 75 MHz range (three standard Lectrosonics blocks), matching the tuning ranges of SSM, LT and LMb "large bandwidth" transmitters. VRT2 modules incorporate Lectrosonics’ new IQ dynamic tracking filters, which accommodate a wide range of transmitter RF power levels while also enabling extremely tight channel spacing—critical features as the available RF spectrum continues to shrink.
-
Model 2215 -
Empower RF Systems, Inc.
The 2215 is suitable for octave bandwidth high power CW, modulated, and pulse applications. This amplifier utilizes high power GaN devices that provide wide frequency response, high gain, high peak power capability, and low distortions. Exceptional performance, long-term reliability and high efficiency are achieved by employing advanced broadband RF matching networks and combining techniques, EMI/RFI filters, and all qualified components. The amplifier is constructed within a single 5RU drawerincluding the forced air-cooling. Available operating voltage configurations are single-phase 220 VAC up to 400 Hz and 28 VDC.
-
380X Upgrade -
Teledyne FLIR
The Star SAFIRE® 380X is a hardware, firmware, and software upgrade to support advanced image aiding features for our globally renowned Star SAFIRE 380 gimbal systems, including Star SAFIRE 380-HD and 380-HDc. The new 380X skillet upgrade reduces operator workload for faster, smarter decision support and features customizable configurations for multi-tile video management and visual user interface, and touchscreen and streaming tablet support. It also features an integrated moving target indicator (MTI) and de-scintillation filter, that removes atmospheric effects to reveal clearer, sharper detail from greater distances.
-
Teledyne LABS
Teledyne Hanson's diverse range of dissolution tester accessories significantly expands the functionality of their instruments, catering to various applications such as small volume testing, Chinese small volume testing, semisolids testing, and immersion cell usage per USP <1724>. The lineup includes:- Precision dissolution vessels- Vessel covers- Paddles (USP Apparatus 2)- Baskets (USP Apparatus 1)- Paddle over disk “transdermal sandwich (USP Apparatus 5)- Rotating cylinder (USP Apparatus 6) - Sampling probes- Small volume kits- Filter block kits- Humidity-sealed dosage-drop chambers- Stationary basket and cover
-
CPCI-ADDA -
ALPHI Technology Corporation
The CPCI-ADDA module offers a complete solution forhigh performance data acquisition applications. Boththe ADC’s and the DAC’s use 10 mS converters thatwill support up to 100khz signals. The CPCI-ADDAsupports P.I.D. loop closure frame rates of up to 4 KHzper channel. The CPCI host can download gain andsetpoint changes on the fly. The CPCI host can readback the current values for feedback, error, setpointand output drive on each channel. The local DSPprocessor can be used for data processing such asdigital filters and FFT’s. The DSP can also be used asa waveform generator to drive the 16 bit DAC.
-
GDYT Series -
HV Hipot Electric Co.,Ltd.
GDYT series include partial discharge power frequency testing transformer(YDTW),partial discharge detector(GDJF2008),Isolation filter frequency doubling power device(GDSF-81G) and power frequency withstand voltage control table(GDYD table).It widely used in electrical manufacturing,power operation departments, research institutes and universities.
-
E4982A -
Keysight Technologies
The E4982A LCR Meter provides the best performance for the passive component manufacturing such as SMD inductors and EMI filters, where impedance testing at high frequencies (1 MHz to 300 M/500 M/1 G/3 GHz) is required. Not only for the manufacturing, the E4982A can also be utilized for R&D, quality assurance with the powerful functions such as list measurements.
