Showing results: 241 - 255 of 690 items found.
-
16196C -
Keysight Technologies
The 16196C surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results - reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement - now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
16196B -
Keysight Technologies
The 16196B surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results, reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement. Now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
16196A -
Keysight Technologies
The 16196A surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results - reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement - now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
CAMI Research Inc. (CableEye®)
A USB Type-C test interface board for CableEye® cable and harness testing systems. Consisting of a daughter board, populated with two USB-C female connectors, it allows users to continuity-check USB Type-C terminated cables using the CableEye tester while seeing the connectors-under-test rendered graphically. The CB26U fits all CableEye models. Configuration A leader in development of PC-based cable and wire harness, continuity, resistance and hipot test systems for over 20 years, CAMI offers the CableEye suite of products complete with accessories – including “connector boards”. The selection of these test fixture boards is constantly growing and is currently numbering over 60 – most of which are populated with ‘families’ of connectors. When pre-populated boards are used, the tester GUI automatically displays a graphic of the connectors under test. Sold as a set of two boards, each CB26U accepts two USB Type-C connectors. In addition to the latest CableEye software, it requires the CB26 small-frame motherboard (Item 756) for operation, and plugs into one of two available slots – two USB-C-connectors can be tested simultaneously. The CB26 (with CB26U) attaches to the tester like a regular connector board. Contact sales@camiresearch.com or +1 (978) 266-2655 for a quote.
-
AUT20044 Rev:B0 -
Allion
The original Intel USB-C 3.1 Tx Test Fixtures includes two types of fixtures, UFP and DPF. Allion Pre-Cert Test Fixture integrates functions of the two fixtures into an one-board solution, eliminating the hassel to frequent switching of two fixtures.
-
PinMap™ -
CAMI Research Inc. (CableEye®)
Check out this fast and super-easy pin-mapping process enabled by our optional CableEye® PinMap™ software. Map as fast as you can move the probe from one pin to the next. Use on your custom connectors, test fixtures, specially-built connector panels, or pigtail adapters to your CableEye tester. This software assigns test point numbers to connector types and applies standard pin designations to the pin numbers. For each custom connector, first choose a connector graphic from our large library to match your connector. Then touch the tester probe to the connector pins one-by-one to automatically detect and assign a test point to each pin. A synthetic voice reads probed pins as you touch them so you don’t need to take your eyes off the connector you’re probing. Finally, enter pin labels of your choice if you wish to override the standard designations.
-
AUT17094 -
Allion
This product is designed for USB-C USB2.0 Receptacle Host Electrical Test.
-
B1505AP -
Keysight Technologies
B1505AP provides eight different pre-configured packages that satisfy a wide variety of power device measurement requirements. The package can be selected according to voltage / current range and the requirement for capacitance measurement.
-
atg Luther & Maelzer
For higher quantities universal fixture tester are the best economical solution.They combine highest throughput with affordable fixture technology especially in comparison to testers utilizing dedicated fixtures.
-
Iwasaki Electric Co., Ltd.
EYE / Iwasaki has developed a family of products to address the most demanding test requirements. This includes Overhead Fixtures, Portable Floor and Pit Fixtures, and On-Board Lighting Fixtures.
-
Testing House, Inc.
In Circuit Test Program Development. Provide you with programming and fixture build as well as schematic review. Will order the fixture from one of our preferred vendors or any Fixture Vendor you prefer.
-
ATE Systems
There are no good measurements without good test fixtures. Ideally the test fixture needs to make the electrical connection between the test instrument and the device-under-test (DUT) and be electrically transparent. ATE has developed fixtures for SMT components, leadless packages, and miniature coaxial interfaces, in such a way that the fixture effects can be removed, and the measurement reference plane can be brought right down to the DUT.
-
Kyoritsu Testsystem Co., Ltd.
Various type fixtures which are hand-press type checker, air press type test fixture , Integrated inspection circuit checker cam be produced as per requests.
-
Circuit Check, Inc.
Circuit Check’s bi-level and multi-stage fixtures combine multiple test levels in a single fixture using controlled actuation and selected probe travels for powered and unpowered tests.
-