Showing results: 31 - 45 of 48 items found.
-
H71002400 -
6TL Engineering
The 6TL24 is the Base platform ideal for Combinational test (ICT+FCT) in low to mid volume, high-mix electronics productions. A dual-stage pushing mechanism will allow performing both, the FCT and the ICT test, without the need of changing the test platform and with a low cost fixturing technology. To do so, the exchangeable cassette fixture must be designed with two-level probes. IN the 6TL24, the second level is reached thanks to a pneumatic actuator.
-
5000 Series In-line Handler -
Circuit Check, Inc.
The Circuit Check 5000 Series In-line Handler is an integrated inline solution that combines automation, fixturing and measurement hardware in addition to other in-line PCBA probe based test stations, while adding a standardized quick change fixture interface. The 5000 series in-line is a unified solution that is software and hardware agnostic, enabling adaptability to a variety of off-the-shelf lower cost ICT, flash and functional test software and hardware.
-
Keystone Compliance
Vibration testing is essential to determining the ability of a product to withstand the conditions that it might experience either during operation or transit. As important as vibration testing is, selecting the right vibration lab to work with is even more important. It is common for units to be over-tested or improperly fixtured. An incorrect fixture can either mask problems with a unit or create a failures that do not actually exist. Proper vibration fixturing is crucial and something that the dynamics testing team at Keystone Compliance is very experienced with.
-
310104435 -
Virginia Panel Corporation
Runners along the platform provide a smooth-sliding action, ideal when using fixtures up to 180 pounds. The 9025TR can be adapted to accommodate vacuum or mechanical fixturing. VPC modules can be intermixed to establish flexible custom interfaces which are ideal for functional and system testing applications. The 9025TR uses all standard VPC 90 series modules and contacts, includes a microswitch and is available with optional table legs and keyboard tray kit. Slide kit required, but not included.
-
F9 Systems, Inc.
The CalBlade backplane calibration fixture isdesigned to permit accurate and convenient impedance and transmission measurements of a HM-Zd backplane. The CalBlade is used to calibratethe logic card connector interface to the backplane rather than to the usual far-end of the coaxial measurement cables. Very accurate impedance, skew and propagation delay measurements are possible since parasitic fixturing effects are removed.
-
DC1000A -
Voltech
To guarantee the quality and performance of inductive components such as inductors, chokes and transformers they are tested at their real-life operating point. If the inductor is designed to carry a DC current, then its inductance must be measured with that DC current present. Until now, these measurements were made by an LCR meter connected via special interfacing to a DC bias supply available only from the manufacturer of the LCR meter. The unique NEW DC1000A can be used with any precision LCR meter and connects simply into existing test fixturing.
-
FixGenius -
Ucamco N.V.
Tests show that FixGenius’ rule-based probe-mapping algorithms reduce pin deflection by up to 25% compared with traditional fixturing packages. FixGenius comes with a powerful Fixture Editor that allows the user to change the probe mapping. If a solution is mathematically possible, FixGenius’ algorithms will find it, and pick the one with least deflection. If the job simply cannot be done with one single fixture, FixGenius will fully automatically split the test into multiple fixtures or into fixture and flying probe test sets, with guaranteed test integrity.
-
Circuit Check, Inc.
Functional test typically applies full operational power to a final product or a loaded printed circuit board in order to determine if the Product/ PCB performs functions as designed. This type of test often involves custom built test equipment and custom test fixturing. Circuit Check supports all forms of functional test strategies within its Signature Series functional test fixtures.
-
10753B -
Keysight Technologies
The Keysight 10753B Tripod provides a mounting for the Keysight 5519A/B laser head. The tripod allows Keysight 5530Laser Calibrationsystem optics to be located remotely from the laser head, yielding greater accuracy and simplifying fixturing. The remote setup also eliminates heat-caused distortions. The Keysight 10753B adjusts for height, rotation, tilt, and lateral offset. The tripod is collapsible, covers a height range of 900 mm (35.5 in) to 1630 mm (64.0 in), and has a net weight of 14 kg (31 lb). The Keysight 10753B tripod complements a family of measurement optics and lasers that comprise Keysight laser interferometer calibration systems.
-
Pacific Testing Laboratories
Careful attention to specimen preparation is critical to obtaining top quality test data. Pacific Testing Laboratories has, what it believes to be, the most extensively equipped machine shop in any commercial laboratory. Its function is dedicated to fabricating test specimens and fixturing. Principal equipment includes diamond coated tooling, surface grinders, milling machines, lathes, a 30 ton precision press, laboratory presses, and a 4-axisCNC milling machine.
-
ESS5/11 SERIES -
ESPEC North America, INC.
The ESS5/11 Series provides the unique capability of stress screening products in a small, lab-type chamber. Pre-qualification for ESS, troubleshooting, and small scale ESS programs would all benefit from high air flow, high change rate testing in this compact design. This series can accommodate up to six product drawers from our standard ESS systems. Other features include non-CFC/HCFC design, and wide variety of control systems, refrigeration system sizes, and product fixturing options.
-
SCR ELEKTRONIKS
The High voltage tester for routine testing of MCBs combines a conventional high voltage tester with a specially designed robust fixture to hold 20 single pole MCBs at a time. The solution comes as a single trolley with easy-to-set test parameters with safety interlocks designed for user safety with respect to electric shock and mechanical fixturing. An advantage of the system is – it gives a high yield (20 MCBs are tested in about one minute) thus yielding user safety at a high value for money.
-
PA-3000-A ETCHER -
TEK-VAC INDUSTRIES Inc.
Process chamber with plasma view window and full access hinged door. RF hot process shelves with opposing ground electrodes. Throttle valve. Capacitance manometer. Internal pumping system with option for Fomblin filled chemical series mechanical pump. Flow control electronics and cabinet. Up to four mass flow control assemblies can be incorporated into our system. RF matching network and 600 watt maximum power supply. Fully enclosed cabinet. Custom internal fixturing to accommodate specific substrate shapes and sizes. Plasma gas selection for optimal performance.
-
5530 -
Keysight Technologies
The configurable system offers all the components you need to perform a variety of measurements using the USB on your PC as the host controller and power source. For basic linear measurements you will need the USB Axis Module, USB Sensor Hub, Air and Material Sensors, Sensor Cables, Software, Laser, Laser Cable, Remote Control (optional)and the Linear Optics Set. Other available options include the Laser Tripod (with laser mounting plate), optics and fixturing kits for making additional types of measurements, and wheeled transit cases.
-
Equip-Test Kft.
More then ten years of experience in special, customized engineering and manufacturing brought us to the highest level of creating reliable, flexible and robust Test Fixtures. Currently our HQ is located in Vecsés, Hungary together with our R&D. Equip Group has Test Fixture Kit manufacturing plant in Serbia, focusing on supplying competitive, high – quality and high – volume products for the global market.With more then 180 employees, Equip – Test is able to offer our customers turnkey solutions in fixturing with test program generation. No matter if you have a simple or complex, high-density PCB (Printed Circuit Boards), or if you have DUT (Device Under Test) already assembled into metal or plastic housing, we can offer you a very stable technical solution.
