Showing results: 256 - 270 of 1121 items found.
-
F56 -
Beijing Airport Beiguang Instruments Co., Ltd
F56 Metal Tube Float Flow meter Series are used for measure instantaneous and accumulated flow rate of liquid, gas and steam in closed pipelines. It is suitable for metering flow value on site or electronic remote. The measuring principle is based on the hydrodynamic effects,This makes float moving from bottom to top in vertical Pipe. As the displacement of float is in related to flow rate, which can be read from the indicator by means of the magnetic drive system in non-contact form . Also, flowmeters output electrical signal (4-20)mA / hart communication protocol with high / low limit Warning switches/integrating flow PCB broad can be configured.
-
PTFM-ONE-DT -
HORIBA, Ltd.
The Dual Pitot Tube Flow Meter, PTFM-ONE DT is a standalone interface for measuring exhaust gas flow rate of combustion engines. The system uses the tried-and-tested pitot tube principle with high-frequency transducers, with a sampling rate of 1kHz to accurately measure highly pulsating exhaust flows. This rapid capture rate ensures that any pulsations or exotic behaviour caused by the engine is measured, and the unique design of the PTFM-ONE DT means reverse flows can be calculated, with the same guarantee of sensitivity.
-
R&B Instrument Inc.
The RBCM Coriolis or Thermal Mass flow meter is measurable of liquid, gas, liquid-solid and gas-solid two phase fluid mass flow instantaneous rate and cumulative total and realizes display and remote transmitter of all measuring parameters.
-
P117 -
Gentos Measurement & Control Co.
P117 is a hand-held flow meter equipped with external clip-on transducers, which can meet the needs of convenient and fast flow measurement, allowing you to quickly transfer and measure data between different working environments and improve work efficiency.
-
-
Criterion D500 -
HORIBA, Ltd.
This leading-edge pressure insensitive mass flow module is installed with differential pressure detection and a piezo actuator valve.
-
Endress+Hauser AG
Flow measurement for liquids, gases and steam. Consistent product quality, safety, process optimization and environmental protection – these are only a few reasons why industrial flow measurement is becoming more important all the time. Water, natural gas, steam, mineral oil, chemicals are some of the fluids that have to be measured day in, day out.
-
Fluke Calibration
The GFS dynamic gravimetric mass flow calibration system allows users to maintain the accuracy and traceability of molblocs or other high precision devices using the same primary reference used by Fluke Calibration. GFS is a true mass flow reference suitable for use in premier measurement institutes who require the lowest measurement uncertainty.
-
FSM3 -
CKD Corporation
It is a flow sensor that can support 5 types of gas such as air, nitrogen, argon, carbon dioxide, mixed gas with one unit.
-
TG050 -
TESTEX Testing Equipment Systems Ltd.
The flow of water within the plane of a geotextile or geotextile-related product is measured under varying normal compressive stresses, with typical hydraulic gradients and with defined contact surfaces.
-
P-Series -
MKS Instruments
P-Series High Performance Multi-gas, Multi-range, Thermal Mass Flow Controllers are designed for the most critical process applications where accuracy, repeatability as well as pressure insensitivity are requirements.
-
SEC-Z700X Series -
HORIBA, Ltd.
The SEC-Z700X Series is equipped with reliable thermal sensors and a pressure insensitive function for stable flow rate control. The on-board pressure measurement reduces the cost, size and complexity of gas delivery systems.
-
RealFlow -
HORIBA, Ltd.
The RealFlow ultrasonic sensor from HORIBA represents a breakthrough in fuel flow measurement technology, for both the compactness in size and its high level of accuracy.The RealFlow has been designed for the ultra low-volume fuel flow conditions found in today’s high-efficiency road car engines, making it an ideal tool for R&D as well as emissions testing to the RDE and WLTP standards - especially with its ability for true engine bay installation due to being so compact in size - a real game changer in the Automotive industry!
-
Ginolis Ltd.
We provide production automation solutions for lateral flow device manufacturing. Our standard modules give you the flexibility to make a wide range of products without compromising quality, with a single automation line taking a minimal footprint in your cleanroom.
-
ForTest Italia Srl
T8730 was designed for the precise task of measuring flows on parts such as filters (medicinal, diesel or petrol), tubes, nozzles, openings, valves, etc…Other than the classic flow measurement, the tool also has other ways of making it as versatile as possible in its category: ascent and descent ramps, opening tests and burst testing.Another separate function is the "continuous measurement", i.e. a test with infinite times allowing adjustment of the taps and part repairs in real time.The tool also avails of an intelligent pressure adjustment, which uses the automatic pressure regulator to continuously adjust the test pressure based on the variation in load loss, to ensure the reading is as stable and repetitive as possible.