Showing results: 2146 - 2160 of 4221 items found.
-
743 Family -
CAEN S.p.A.
The 743 is the Switched Capacitor Digitizer family, based on the SAMLONG chip and developed in collaboration with CEA/IRFU, with a good compromise between high sampling frequency (3.2GS/s) and channel density. It can record very fast signals from scintillators coupled to PMTs, Silicon Photomultipliers, APD, Diamond detectors and others, and save them with high efficiency and precision for advanced timing analysis.
-
Typhoon 4.0 PLUS -
Qualmark Corporation
This system is designed specifically for the task of performing Highly Accelerated Stress Screening (HASS) and HALT on large products. With the Lowest Total Cost of Ownership within the AST industry, the 48" x 48" vibration table is capable of supporting hundreds of pounds of products and fixturing, and delivers more energy in the lower frequency ranges necessary to stimulate failures in these large products.
-
7052PH -
ACO Pacific, Inc.
The 7052PH Type 1.5TM phantom powered measurement microphone system offers a cost effective solution to acoustic measurements from phantom powered sources. Type 1.5TM - a superior Type 2. Frequency Response: <3 Hz to > 20kHz typ.(capsule). Sensitivity: 22 mV/Pa (-33 dBV/Pa)typ. Dynamic Range (capsule) 1% THD: <20dBA-150dBSPL (Capsule).
-
IOScope -
Faber Acoustical, LLC
With IOScope, measure loudspeaker impedance, frequency response, and sensitivity. Measure a room impulse response. Tune a large sound reinforcement system, time-align a set of surround sound speakers, or optimize your home stereo. Determine the actual cutoff frequencies of your latest speaker crossover circuit, or teach your students the fundamentals of Fourier analysis of dynamic systems.
-
Radiant Technologies, Inc.
The Precision Multiferroic tester is Radiant's most advanced test system. The Multiferroic has fast built-in frequency at 30kHz measurements using the 200V internal amplifier and 50kHz measurements using the 100V internal amplifier. This system comes in a built-in option of +/-100V, 200V, and 500V and can be expanded to 10kV. This unit also comes with a 18 bit ADC and requires no configuration changes.
-
Microchip Technology Inc.
With the massive growth of the Internet of Things, wireless connectivity has never been more important. Quickly incorporate connectivity into your designs with wireless ICs, modules, software and development kits that make connecting effortless for your customers. Our comprehensive wireless portfolio has the technology to meet your range, data rate, interoperability, frequency and topology needs.
-
T-SENSE -
HÜBNER Photonics
The Terahertz imager T-SENSE ® visualizes enclosed hazardous substances precisely in letters as well as small parcels safely and effectively.The process is safe, fast and without risk to the health of the user. Unlike conventional visualizing processes such as x-ray technology, the T-SENSE ® functions on the lower Terahertz frequency level with safe millimeter waves that enable non-transparent materials to be illuminated.
-
openQCM
The sensor is a surface sensitive quartz crystal capable of measuring phenomena at molecular scale. It works in vacuum, air and liquid environments. The QCM sensor is based on the piezoelectric properties of the quartz crystal. The application of an alternating current causes the mechanical vibration of the quartz crystal in the MHz range. The QCM technique measures the variations in quartz frequency for measuring the mass variations on its surface.
-
Altair Engineering, Inc.
Altair software is used across industries to solve a broad range of electromagnetic problems from static to low and high frequencies. Whether your application requires multiple frequency and time-domain techniques with true hybridization to enable efficient exploration of a broad spectrum of electromagnetic performance, or the simulation of magneto static, steady-state and transient conditions, we have the tools you need.
-
Wayfind'r -
Timco Instruments, LLC
The WAYFIND'R Impulse Cable Tracer was originally designed for electric utility use to accurately identify the route of buried secondary cables. Because the WAYFIND'R imposes an audio frequency signal on the cable, the signal is not induced into adjacent cables or pipes, eliminating false signals. The WAYFIND'R may also be used fro tracing indoor wiring and buried shielded primary cables.
-
M9182A -
Keysight Technologies
The Keysight M9182A is a 6digit PXI digital multimeter that measures common parameters such as DCV, DCI, ACV, ACI, 2- and 4-wire resistance, frequency, capacitance, and temperature. It offers 40 ppm basic DCV measurement accuracy, excellent noise rejection, and handles inputs of up to 300 V. The M9182A offers advanced triggering capabilities, including pre and post triggering.
-
S95029B -
Keysight Technologies
The S95029B noise figure application enables high-accuracy noise figure and noise-power measurements of amplifiers, frequency converters, and mixers by using the Keysight vector-source-correction technique. Using a source-impedance tuner to remove the effects of imperfect system-source match, this technique produces higher accuracy results than Y-factor method and other cold-source implementations--especially for in-fixture, on-wafer, and automated-test environments.
-
M8195A -
Keysight Technologies
Sample rate up to 65 GSa/s High channel density: 1, 2 or 4 channels per module, synchronization of up to 16 channels on 4 modules with the M8197A multi-channel synchronization module Built-in frequency and phase response calibration Embedded DSP enables real-time waveform and impairment generation(in conjunction with the 81195A optical modulation generator software)
-
Applied Image, Inc.
Sinusoidal Target Arrays have been recognized as a superior test method for a variety of applications, from moiré contouring to reliable MTF Evaluation of materials, lenses, cameras, and electro-optical systems (Follow the hyperlink to learn about using Sinusoids for MTF eval). Sinusoidal Pattern Arrays are manufactured on two different materials for both reflective and transmissive applications. Because of the inherent limitations of reflective materials, the maximum spatial frequency of the reflective pattern arrays is limited to 20 cycles per mm, while the transmission film arrays are offered in various sizes up to 256 cycles per mm. In addition, the sinusoidal arrays are available in a Single Frequency Grating or with Multi-Frequency Gratings. If instead of continuous sinusoidal frequency, you are looking for a square wave frequency design, then look to the Ronchi Gratings page. Should you need to alter the size of the pattern or the substrate, fill out our Custom Test Targets and Charts form and start the conversation.
-
Fairview Microwave Inc.
Our waveguide detectors cover a broad frequency range of 26.5 GHz to 110 GHz and are available with waveguide sizes ranging from WR-28 to WR-10. The video output ports utilize SMA female connectors. These high performance zero-biased waveguide detectors exhibit excellent performance in Ka, Q, U, V, E and W frequency bands. These types of waveguide detectors are commonly used in various aerospace, defense and commercial wireless applications used in instrumentation, power detection, power monitoring, direct detection receivers, high frequency communications, radar, SATCOM, point-to-point radio, telecom, data links and R&D. The detector circuits use high performance GaAs Schottky Barrier Beam lead diodes with extremely low junction capacitance. These waveguide detector designs perform with minimal sensitivity variation resulting in a flat frequency response across the entire waveguide band. All of the waveguide detectors are in-stock and ready to ship.
