Showing results: 2431 - 2445 of 4195 items found.
-
CRY6125 -
CRYSOUND
CRY6125 Electroacoustic tester is a full-featured electroacoustic device tester with resistance to environmental noises. It is designed to measure the performance indicators of microphones, electret microphones (MIC), transmitters, receivers, earphones, headset microphone assemblies, communication helmets, speakers/loudspeakers, buzzers and other electroacoustic devices, such as sensitivity (SPL), impedance, distortion (THD), resonance frequency F0, quality factor Q, equivalent volume, and audio power amplifier, etc. Its measurement frequency can be up to 10 Hz - 65 kHz.
-
AB-CLP -
Lisun Electronics Inc.
• EMI Receiver equipped with absorbing clamp can indirectly test radiated interference power of household electrical appliance, power tool and similar electrical appliance with frequency from 30~300MHz.
-
MCR9000 -
Matrix Technology Inc.
MCR-9000 Series is a high precision impedance analyzer with DC 10Hz-30MHz frequency and 10 mV-2Vrms (min. resolution 1mV) test signals, and is suitable for the LCR and DCR tests of AC signals.
-
KVIO-80 -
KV Hipot Power Test Equipment Co.,Ltd
Automatic Insulation Oil Breakdown Tester Is Used to carry on power frequency dielectric break down test on the transformer oil, capacitor oil, electric device, insulation tool etc.
-
AP2019 -
ZETLAB Company
*Can be used as shock sensors in equipment diagnostic systems;*Combination of high axial sensibility, intrinsic frequency and shock resistance;*Low sensitivity to electromagnetic fields;*Low intrinsic noise level.
-
6TL Engineering
Capable of performing the necessary switching between test points of the device under test, to give access to low frequency measuring instruments, in electronic test systems based on tool receivers.
-
1280Z -
Ametek Scientific Instruments
The Solartron Analytical 1280Z Electrochemical Test System is a complete instrument that packages the potentiostat hardware for DC and Frequency Response Analyzer (FRA) hardware for AC tests in a single compact unit.
-
3202 -
Tabor Electronics Ltd.
Model TE3202 is a dual channel RF amplifier in a single slot PXIe form factor that can operate from 100kHz to 20GHz, designed for high frequency, and high power signal amplification.
-
3201 -
Tabor Electronics Ltd.
Model TE3201 is a single channel RF amplifier in a single slot PXIe form factor that can operate from 100kHz to 20GHz, designed for high frequency, and high power signal amplification.
-
N4377A -
Keysight Technologies
The N4377A Lightwave Detector is a USB-powered optical-electrical converter with built-in optical power meter capability. If used with a vector network analyzer or a spectrum analyzer it enables frequency domain applications in photonics.
-
SAMPULSE20x2 -
Furaxa, Inc.
The SAMPULSE20x2 is a demonstration board for the Furaxa SiGe3 30GHz sampler/pulser IC. The SIGe3 IC is a dual channel sampler pulser chip, and the SAMPULSE20x2 demonstration board contains two 2.4mm combined TDR input/output connectors, one to each sampler/pulser channel in the IC. The SiGe3 IC's two sampler outputs are then sent to to two SMA jacks, the first outputting the sample taken on the rising edge of the sampler clock, and the second containing the sample taken on the falling edge of the sampler clock. The sampler clock input, which must be a square wave, may be set to any frequency from 5MHz to 1GHz, causing the board take two pairs of samples (one on each clock edge) at rates from 5 million to 1 billion per second. A pulser clock input, which may be set to any frequency from 5MHz to 2GHz, and MUST be a square wave (preferably differential) with rise time under 100pS, causes the board to produce concurrent pulses on both of the SiGe3's I/O pins, which produce near-concurrent pulses at the two 2.4mm sampler/pulser TDR input/output connectors.
-
Meco Instruments Pvt. Ltd.,
AC Current 40A, 400A, 1000A AC Voltage 4V, 40V, 400V, 750V (Auto) (40-500Hz) DC Voltage 4V, 40V, 400V, 1000V (Auto) Resistance 400Ω, 4KΩ, 40KΩ, 400KΩ, 4MΩ, 40MΩ (Auto) Frequency 10.00 Hz, 50.00 Hz, 500.0 Hz, 5.000 KHz, 50.00KHz, 500.0 KHz(Auto) Sp. Functions Data Hold, Audible Continuity, Diode Test, APO Jaw Opening 43mm Max.
-
HATS -
Brüel & Kjær Sound & Vibration A/S
Designed for realistic in situ electroacoustics tests on, for example, smartphones, headsets, audio conference devices, microphones, headphones, hearing aids and hearing protectors. High-frequency Head and Torso Simulator (HATS) Types 5128-C and -D are manikins with built-in realistic ear and mouth simulators that provide a realistic reproduction of the acoustic properties of an average adult human head and torso. High-frequency HATS is designed for in situ electroacoustics tests and can cover the full audible frequency range (up to 20 kHz).
-
Renesas Electronics Corp.
The ISL911xx buck-boost regulator family is capable of working with the ultra-small inductors and capacitors to fit within less than 14mm2 board footprint, making them the ideal 2A switching converter solution for space-constrained mobile devices. The advanced wafer-level CSP package requires only a single inductor and very few external components, which minimizes overall space requirements. The ISL911xx regulators’ 2.5MHz switching frequency further reduces the power supply solution size.
-
Guzik Technical Enterprises
The Guzik miniature AE sensor with isolated integral 30 dB preamplifier has a wide-band and excellent frequency response over the range of up-to 1 MHz. Its small size makes the sensor ideal for hard disk drive test or similar applications requiring very small size, low weight, wideband AE sensor response and high sensitivity. A small diameter, external flexible cable connects the sensor with a 3-pin JST connector on the other end.