Showing results: 946 - 960 of 4162 items found.
-
KH30935 -
Beijing KeHuan Century EMC Technology Co,.LTD
KH30935 active loop antenna is used for adjusting, testing, measuring and other receivers. It has many advantages:1. The antenna coverage frequency is wide: 150KHz ~ 30MHz .2. The field strength value is measured according to the correction coefficient within the effective frequency range, which is convenient to use.3. The antenna has a small outer diameter and light weight, which is convenient for outdoor measurement.
-
DOWNCONVERTER 10 GHz VXI -
Holding Informtest
The DOWNCONVERTER 10 GHz design assumes its use in closed mobile complexes for field testing of communications equipment. To do this, the device has applied advanced solutions to reduce the phase noise of the output signal in conditions of increased vibration and temperature. The device has a temperature-stabilized reference frequency generator with the ability to output a reference frequency signal. Also, it is possible to operate from an external reference generator.
-
RightMark Gathering
RMClock (formerly known as AMD64CLK) is a simple GUI utility designed for realtime CPU frequency monitoring and realtime adjustment of the CPU multiplier (FID) and voltage level (VID) of the supported CPUs via processor's power management model specific registers (MSRs). In auto-management mode it continuously monitors the CPU usage level (reported by CPU itself) and adjusts the CPU frequency and/or voltage level as required
-
50 GHz -
Virginia Panel Corporation
The 50 GHz coax contacts demonstrate outstanding RF performance from DC to 50 GHz. Our 50 GHz contacts offer the best density for higher frequency requirements, and can be used in micro coax modules for 90 Series systems and iSeries solutions. The contacts are available in patchcords using Flex 405 high frequency wire. For ordering inquires, please contact a Field Application Engineer.
-
28 AND 29 -
Picoprobe
Designed to serve the needs of integrated circuit engineers working in the most advanced high speed, submicron, MOS technology. These high frequency instruments include the attractive features of the Models 18C and 19 including full dc capability, negligible dc current drain, and extremely low input capacitance. In addition the frequency range of the Models 28 and 29 has been extended to a full 1 GHz.
-
E1709A -
Keysight Technologies
The measurement signal frequency changes as the stage velocity changes. The Keysight E1709A ensures minimal phase processing errors due to frequency changes. The receiver also provides immunity to errors induced by changes in measurement signal power that occur due to small pitch, roll and yaw movements during stage motion. These features help provide the most accurate measurements under system motion.
-
U1818B -
Keysight Technologies
The Keysight U1818B 100 kHz to 12 GHz active differential probe makes it easy to perform high frequency in-circuit measurements using network, spectrum and signal source analyzers. With flat frequency response, low noise floor, and direct power from instrument connection, the U1818B allows measurements to be made while taking full advantage of Keysight's RF analyzers dynamic range.
-
U1818A -
Keysight Technologies
The Keysight U1818A 100 kHz to 7 GHz active differential probe makes it easy to perform high frequency in-circuit measurements using network, spectrum and signal source analyzers. With flat frequency response, low noise floor, and direct power from instrument connection, the U1818A allows measurements to be made while taking full advantage of Keysight's RF analyzers dynamic range.
-
S93084B -
Keysight Technologies
The S93084B tunes the network analyzer’s receivers to the output frequency of the converter under test without having to access internal LOs or a common reference signals. For converters with embedded LOs, this enables measurements of match-corrected conversion loss/gain and absolute group delay (requires S93082B and S93083B), gain compression versus frequency (requires S93086B), intermodulation distortion (requires S93087B), and noise figure (requires S93029B).
-
RFA 600 -
Huber Signal Processing
The RFA 600 provides a gain of 20 dB, a highly linear frequency range with ±0.25 dB, a switchable 50 or 0 Ω output, and an output amplitude of 22 V. The frequency range now goes from DC up to 600 MHz. Typical Applications are radar, ultra sonic, ATE, VHF transmitter, data calbe drivers, HDTV cable drivers and many more.
-
COMM-connect
The 3030 RF Power Meter is a modern version of the traditional Antenna Watt and VSWR instrument. The instrument cover communication bands from 30MHz to 500MHz. The 3030 RF Power Meter will measure forward and reflected power in the range from milliWatts up to 100Watts. Built in frequency counter. The counter will show the transmit frequency and will call the calibration table for the actual frequency. Outside the range of the counter the instrument can be set into manual mode giving a wider dynamic range. The 3030 RF Power Meter will calculate VSWR or Return Loss, and features Peak and Hold mode. Accessory kit with soft or hard carrying bag, car charger and coax adapters for standard types are available
-
SHF Communication Technologies AG
SHF’s microwave components are broadband devices suitable up to 110 GHz. Our SHF BIAS TEES are well known but perhaps a slight variation does suit your application even better. DIPLEXERS are bias tees with a certain bandwidth in the low frequency path to combine or separate high frequency and low frequency signals into or out of a single line. DC-FEEDERS are bias tees without the capacitor. Therefore, it provides slightly lower insertion loss in case it is connected to an AC-coupled device which already has a capacitor on its input. Based on our air line construction, these passive components provide resonance-free transmission over the entire operating range.
-
ERAVANT
Dielectric resonator oscillators (DRO) are free running oscillators that utilize state-of-the-art planar circuits, three-terminal devices and dielectric resonator technology to generate high-quality microwave signals with excellent frequency stability. In addition, these oscillators are equipped with an internal voltage regulator that further improves the frequency stability by isolating the external bias pushing and modulation. In general, these oscillators are fixed. However, a small mechanical or electrical tuning range can be achieved by use of a self-locking screw or an integrated Varactor diode. The standard offering covers the frequency range of 2 to 40 GHz. While standard models are equipped with female SMA and K connectors at the RF port, other RF interface options are also available.
-
CMXHEAD50 -
Rohde & Schwarz GmbH & Co. KG
The R&S®CMXHEAD50 is the only remote radio head for signaling that offers bi-directional testing at five mmWave frequency bands and additional EVM booster ports - all within one hardware set. It covers all 3GPP frequency bands in FR2-1 between 22 and 50 GHz: n257, n258, n259, n260, n261 and even the new n262 frequency band that features 1000 MHz of bandwidth between 47.2 and 48.2 GHz. With active mmWave combiners from R&S up to four R&S®CMXHEAD50 can be combined to enable advanced scenarios such as interband carrier aggregation 28 GHz + 39 GHz.
-
8474E -
Keysight Technologies
The Keysight 8474E is a high-performance detector using a gallium arsenide, planar-doped barrier detecting element. It features extremely flat frequency response over its entire band of operation and very good frequency response stability versus temperature. The Keysight 8474E is also very rugged with high resistance to ESD damage. The Keysight 8474E detector is available with a 2.4-mm (0.01 to 50 GHz) connector. This detector offers the options for optimal square-law loads (Option 102) and for positive polarity output (Option 103). Because the unit-to-unit frequency response tracking of this device is typically better than plus or minus 0.3 dB, no matched response option is offered.
