Showing results: 2881 - 2895 of 2953 items found.
-
Transcom Instruments
The G6 VSG from Transcom Instruments is a Vector Signal Generator that operates from 10 MHz to 6 GHz. It can simulate GSM, EDGE, CDMA, TD-SCDMA, WCDMA, CDMA2000, TD-LTE, FDD-LTE, NB-IoT, and LoRa base station signals for production and calibration of UE, chips. The signal generator has a dynamic range (power range) from -100 to 10 dBm and an in-built automatic gain control function. It is available in a module that measures 180 x 50 x 290 mm and is ideal for educational practices, wireless monitoring, mobile communication, aerospace and national defense industry in terms of research, manufacturing, testing and measurement, and electronic countermeasure.
-
Cuming-Lehman Chambers
– 80dB RF shielded enclosure (inside dim.- 5’ high x 5’ wide x 7’ long)– Fabrication, Construction, and Transportation– Free standing shielded enclosure design including structural support system– Enclosure will be installed over a continuous 1/8″ dielectric underlay and polyethylene vapor barrier– Modular wood-core panel construction– Bulkhead connector panel – (1) 12” x 12”– RF shielded doors – (2) 2’ x 2’– One (1) Antenna Sinclair Model SP-440-SF2SNF– Shield test per IEEE –STD 299- supersedes MIL-STD-285 (Tested @ 1 GHz)– RAM
-
Teledyne RF & Microwave
For over three decades, Teledyne Microwave Solutions has built a strong heritage delivering advanced value added services to the military, space and industry sectors of aerospace. With test capabilities up to 40 GHz, TMS offers chip and wire assembly of products ranging from single die through complex hybrids which can then be submitted to a combination of customer-specified RF and DC testing and environmental screening. TMS offers a complete portfolio of screening and testing services for device sorting, labeling, lead forming and tinning, and tape-and-reel packaging, as well as LAT services on packaged devices or bare-die, including diodes, transistors, and MMICs.
-
Innovative Technical Systems
Innovative Technical Systems has designed many instrumentation systems for radar cross section (RCS) measurements. Some of the designs are based around standard network analyzers for signal processing, while utilizing high PRF short-pulse RF transceivers with gated IF architecture. The modular design approach uses separate transmitter and receiver modules for monostatic or bistatic measurements. Compact module design provides flexibility to mount the transmitters and receivers close to the antennas. Dual-channel designs permit full polarization matrix measurements with either electromechanical or solid-state switches. Modules are available in various bandwidths that extend from 100 MHz to over 100 GHz.
-
BBA130 -
Rohde & Schwarz GmbH & Co. KG
The R&S®BBA130 broadband amplifiers provide RF output power between 22 W and 13000 W over the frequency range between 80 MHz and 6 GHz. The robust amplifiers offer flexible setting options so that an optimal RF signal can be generated for the specific application. It is therefore possible during operation to adjust the bias point for the transistors between Class A and Class AB and to change the mismatch tolerance at the output to provide more power. The air cooled amplifiers have a compact, modular design and are suitable as desktop models or can be installed in a rack. Its upgradability in frequency and power safeguards customers' investment.
-
SMB100A -
Rohde & Schwarz GmbH & Co. KG
The compact, versatile R&S®SMB100A microwave signal generator with a frequency range up to 40 GHz provides outstanding spectral purity and high output power. In addition, it features easy operation, comprehensive functionality and low cost of ownership. The R&S®SMB100A provides microwave characteristics that are exceptional in its class, making it an excellent general purpose instrument. Its outstanding characteristics, compact size and low weight make the instrument ideal for a wide range of applications. The R&S®SMB100A is optimally suited for use in development, production and service, or simply wherever an analog microwave signal is needed.
-
Teledyne Defense Electronics
For over three decades, Teledyne RF & Microwave has built a strong heritage delivering advanced value added services to the military, space and industry sectors of aerospace. With test capabilities up to 40 GHz, Teledyne offers chip and wire assembly of products ranging from single die through complex hybrids which can then be submitted to a combination of customer-specified RF and DC testing and environmental screening. We offer a complete portfolio of screening and testing services for device sorting, labeling, lead forming and tinning, and tape-and-reel packaging, as well as LAT services on packaged devices or bare-die, including diodes, transistors, and MMICs.
-
Z‑Series -
Keysight Technologies
At the extremes of electrical and optical measurements, you need to make rise time measurements without being limited by scope bandwidth. You need to see your signal and not oscilloscope noise, and you need fast analysis and hardware acceleration. The Infiniium Z-Series delivers this and more with its RealEdge technology enabling 63 GHz of oscilloscope bandwidth and superior signal integrity. The Z-Series takes advantage of indium phosphide chip technology and custom thin film packaging to give you extremely low noise, low jitter, and high effective number of bits. These technologies allow you to see the true representation of your signal.
-
LMS Series -
Vaunix Technology Corporation
The Lab Brick LMS series of high frequency RF and microwave USB-compatible, synthesized signal generators cover a frequency range from 0.5 MHz - 20 GHz with low noise, fast 100-microsecond switching time, and fine 100 Hz frequency resolution. They require no additional DC supply voltage and offer advanced features such as phase-continuous linear-frequency sweeping, internal/external 10 MHz reference, and optional pulse modulation. GUI software can track and control several connected signal generators, simplifying multiple-signal test setups. Each device stores settings in internal memory, allowing it to power up in a specific instrument state.
-
S95011B -
Keysight Technologies
This application enables the analyzer to perform enhanced time domain analysis for high-speed data applications. All functionality of the S95010B are included (TDR/TDT mode). In addition, the S95011B enables more detailed measurements and evaluations, such as eye-diagram / mask modes, without adding PLTS software. Jitter and emphasis / equalization capabilities enable simulation of real-world signals and environment. The S95011B covers up to 53 GHz bandwidth. Full calibration is available and the automatic deskew ensures easy removal of fixture and probe effects. To get the best accuracy, mechanical calibration kits or ECal with DC option (i.e., N469xD or N4433D with Option 0DC) are recommended.
-
S96011B -
Keysight Technologies
Use S96011B to perform enhanced time domain analysis for high-speed data applications. Includes all functionality of the S96010B (TDR/TDT mode). In addition, the S96011B enables more detailed measurements and evaluations, such as eye diagram / mask modes, without adding PLTS software. Jitter and emphasis / equalization capabilities enable simulation of real-world signals and environment. The S96011B covers up to 53 GHz bandwidth. Full calibration is available and the automatic deskew ensures easy removal of fixture and probe effects. To get the best accuracy, use mechanical calibration kits or ECal with DC option (i.e. N469xD or N4433D with Option 0DC).
-
MixAMC-I -
Virginia Diodes, Inc.
Virginia Diodes'' standard Spectrum Analyzer Extension Modules (SAXs) provide high performance broadband down-conversion and frequency extension of microwave specturm analyzers into the THz range. VDI now offers integrated MixAMC modules that provide industry leading performance in a compact package. These integrated MixAMC modules are used to down-convert millimeter-wave / THz signals only. Spectrum Analyzer Extension mode is not currently available for the MixAMC-I products. Integrated MixAMC modules utilize a low frequency LO input (<20 GHz) and have a seprate IF output port. Integrated MixAMC modules configured for high IF bandwidth may be available upon request.
-
Narda Safety Test Solutions
Real-Time Outdoor Remote Analyzer for the Detection, Analysis, Classification and Localization of RF Signals between 8 kHz and 8 GHz. Supports automatic direction finding and localization via AoA and TDOA. For fixed installation or semi-static use on demand. Solves complex measurement and analysis tasks reliably and quickly with outstanding RF performance. Windows 10-based open platform for third-party applications. The "SignalShark 3330 Outdoor Unit" series is characterized by a robust and weatherproof die-cast aluminum housing with IP65 protection class, which is also used as a heat sink. The compact size allows the receiver to be mounted close to the antennas, keeping the antenna cables short and the resulting sensitivity high.
-
A.H.Systems, Inc.
For many years most standards called for the use of a half-wave dipole antenna set for frequencies above 80 MHz. However, to reduce test time, broadband antennas such as the biconical antenna and log periodic antennas began to be accepted. Broadband antennas, compared to half wave dipoles, reduce test time because the technician did not have to stop the test to adjust the dipole antenna for each frequency. A.H. Systems'' 7 models of Biconical Antennas operate efficiently over the frequency range of 20 MHz to 18 GHz. Suitable for FCC, MIL-STD, VDE, TEMPEST, and immunity testing, each Biconical antenna will provide reliable, repeatable measurements.
-
ERAVANT
Coaxial attenuators are constructed with passivated stainless steel for durable use in both engineering labs and production line environments. These coaxial attenuators are designed and manufactured for low VSWR, low insertion loss and high attenuation value accuracy. The standard offering covers the frequency range of DC to 110 GHz and includes various interface options from 2.4 mm to 1 mm connector types as well as both male and female interfaces. The power handling of standard models is 0.5 to 1 watt continuous wave (CW). Higher power handling levels and different attenuation values and connector types from those listed below can also be requested.
