Filter Results By:

Products

Applications

Manufacturers

Showing results: 346 - 360 of 2956 items found.

  • Modulation Distortion For E5081A Up To 20 GHz

    S960704B - Keysight Technologies

    The Keysight S960704B modulation distortion software application enables fast and accurate active device modulation distortion characterization under modulated signal conditions up to 20 GHz. The wide dynamic range and vector error correction of the ENA-X yield an extremely low residual EVM of the test setup, delivering a complete picture of your device’s signal distortion performance without test system interference. S960704B software measures EVM, NPR, ACPR, and decomposes linear and nonlinear signals by spectrally correlating input and output spectrum without needing to demodulate. Integration with the ENA-X measurement flexibility enables quick modulated signal distortion measurements along with traditional VNA tests.

  • PXIe-5651, 3.3 GHz RF Signal Generator

    PXIe-5651 / 781216-01 - NI

    PXIe, 3.3 GHz, PXI RF Analog Signal Generator—The PXIe‑5651 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXIe‑5651 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.

  • PXI-5651, 3.3 GHz RF Signal Generator

    779670-01 - NI

    3.3 GHz PXI RF Analog Signal Generator—The PXI‑5651 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXI‑5651 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.

  • 26.5 GHz Single-Mode Lightwave Component Analyzer

    N4375E - Keysight Technologies

    The new N4375E single-Mode LCA is based on the latest 5222A series network analyzers with 2-port or 4-port configuration. This LCA is the ideal measurement solution for electro-optical components up 26.5GHz electro-optical components, as well as Radio over Fiber (RoF) and aerospace and defense (A&D) electro-optical test applications. The N4375D is traceable to international standards and provides guaranteed specifications for electro-optical responsively S-parameter measurements in a turn-key solution. In combination with N4691B electronic calibration kit you get fastest setup of your test, so you can focus on developing your components. The new N4375D replaces the industry standard 8703A/B series and supports specified modulation frequencies up to 26.5 GHz at 1310nm and 1550nm source wavelength or individual wavelength with external optical input.

  • 60 GHz WR-15 Waveguide Tx Module

    PEM010 - Pasternack Enterprises, Inc.

    The PEM010 is a highly integrated millimeter wave transmitter that covers the 60 GHz global unlicensed spectrum allocations packaged in a standard waveguide module. Transmitter architecture is a double conversion, sliding IF with wide bandwidth capability through the up-conversion chain from baseband to carrier. The I/Q interface accepts analog baseband signals which provides for flexibility in design and applications. The baseband input optionally supports FSK/MSK modulation for non-coherent applications. The transmitter incorporates a complete waveguide interface with low-loss transition between the chip and the WR15 waveguide port. The integrated package is small and lightweight, with a simple to use multi-pin ST4 connector for power, reference clock, digital control port and baseband signals. Either of two reference clocks can be used for setting 540 MHz or 500 MHz channel spacing.

  • Semi-Rigid Test Probes Up to 6 GHz

    Fairview Microwave Inc.

    Fairview Microwave’s semi-rigid test probe assemblies come in multiple cable diameters to help when attaching the unterminated end of the probe to a circuit board trace. There are two versions including straight-cut probe ends for those that would like to customize the dimensions of the center conductor and dielectric dimensions, as well as pre-stripped probe ends that are ready for immediate use. By soldering the outer conductor to the signal ground and the exposed center conductor to the trace carrying the signal of interest, simple sampling measurements can be made without having to create a separate subassembly circuit board or add a connector to the circuit layout which can take up valuable real estate. Fairview provides 3 diameters of semi-rigid coax and 3 different lengths from 3 inches to 12 inches to fit a variety of trace widths and applications. All test probes are 100% RF tested to ensure the cable assemblies operate to 6 GHz and also to make sure that the SMA connector interface meets the 1.35:1 VSWR specification prior to shipping. To protect the small diameter coax from damage, each part is shipped in a clear protective tube that can also be used for storing the probes for future use.

  • Coax Module, ITA, 20/26 GHz, 17 Position. For use with 20/26 GHz ITA contacts with SMA adapter

    510108240 - Virginia Panel Corporation

    Coax Module, ITA, 20/26 GHz, 17 position. For use with 20/26 GHz ITA contacts with SMA adapter.

  • Frequency Converter from 2 to 3 GHZ

    FCV 300 EVO - Unaohm Start S.r.l.

    The FCV300 EVO frequency converter is an external module that, combined with a field meter,

  • RF Signal Generators, Up to 6 GHz

    SG380 Series - Stanford Research Systems, Inc.

    The SG380 Series RF Signal Generators use a unique, innovative architecture (Rational Approximation Frequency Synthesis) to deliver ultra-high frequency resolution (1 µHz), excellent phase noise, and versatile modulation capabilities (AM, FM, ØM, pulse modulation and sweeps) at a fraction of the cost of competing designs.

  • Straight Waveguide Sections up to 110 GHz

    Fairview Microwave Inc.

    Fairview Microwave’s straight waveguide sections consists of 61 models that are available in sizes ranging from WR-10 to WR-137. These waveguide straights deliver VSWR as low as 1.03:1 and are available in section lengths from 3 inches to 12 inches. They are made of either painted copper alloy or gold-plated, oxygen-free hard copper (OFHC) and feature UG, CPR and UBR-style flanges. These waveguide straight sections are ideally suited for use in industrial, defense, aerospace, test and instrumentation, medical and telecom industries.

  • Source - 20 GHz Source with Amp Attenuator

    RI8554A - Roos Instruments, Inc.

    Automated Instruments, Powerful Development Tools and Worldwide Support

  • 10 MHz to 55 GHz Noise Sources

    CNS346 Series - Spanawave Corporation

    The Spanawave CNS346 Series is designed for precision noise figure measurement applications. The superior VSWR characteristics reduce multiple reflections of the test signals and significantly increase the measurement accuracy of most noise figure set-ups. The CNS346 Series noise sources have broadband coverage and extremely good temperature and voltage stability, for the finest noise figure meter-compatible laboratory standards. Outputs of 6, 15.5 and 22 dB ENR are available, allowing the units to accurately measure noise figures up to 20 ,30 and 36 dB respectively.

  • 13 GHz, 4 Channel Programmable Attentuator

    QPA13 - GigaBaudics Co.

    This device has low impedance mismatch, high bandwidth, wide dynamic range and is capable of rapid state change. The QPA13 can be an attractive alternative to either the manually operated microwave attenuator switches, which are expensive and are switched very slowly, or the relay attenuators which are expensive and wear out quickly.

  • 18 GHz Up/Down Converter & Signal Conditioning

    SC2250 - SignalCraft Technologies Inc.

    The SC2250 extends the useful range of traditional 6GHz RF instruments for operation at microwave frequencies up to 18GHz. It provides excellent integration capability with other modular products such as National Instrument’s Vector Signal Transceiver (VST). Selectable filtering is provided for signal conditioning applications requiring spurious and harmonic rejection.

Get Help