Showing results: 196 - 210 of 250 items found.
-
THA SERIES -
Transducer Techniques, Inc
Our THA Series through hole donut load cells offer an outside diameter of 1.00 inches and up to two different through hole diameter options per capacity range. These load cells are manufactured from heat treated 17-4 ph stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
THC SERIES -
Transducer Techniques, Inc
Our THC Series through hole donut load cells offer an outside diameter of 2.00 inches and up to six different through hole diameter options per capacity range. These load cells are manufactured from heat treated 17-4 ph stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
Accumetrics Associates, Inc.
The AT7000 multi-channel systems can combine any customized mix of ordinary sensors: strain gages, thermocouples, RTDs, accelerometers, as well as motor/generator field voltages, currents and ground fault currents. The received data is continuously streamed to the user as analog (+/- 10V or 4/20mA) or digital data.
-
Advanced Telemetrics International
ATi Telemetry Systems are typically used to transmit data from rotating shafts or machinery to a stationary telemetry receiver. The 2040BC Miniature Strain Gage Transmitter can be connected to strain gauges adhered to propellers or rotors in order to transmit blade strain or shaft torque in flight.
-
SLB SERIES -
Transducer Techniques, Inc
The SLB Series Subminiature load cells (Load Buttons) are offered for compression only applications where space is limited. The matching surface must be flat for ultimate accuracy. The loading diameter is slightly convex for accurate load distribution. These sensors are manufactured from heat treated 17-4ph stainless steel, and the sensing element incorporates bonded foil strain gages of the highest quality. They are sealed for protection against most industrial environments.
-
LCS-3 -
PENKO Engineering B.V.
Load cell simulator particularly useful in a test environment for example to check a program sequence of a controller. The LCS-3 is a simulator used as a substitute for strain gage transducers to generate the precise mV/V signals required in the development , checkout and pre-calibration of signal conditioners, digital and analog readouts and data loggers.
-
TRS SERIES -
Transducer Techniques, Inc
The TRS Series reaction torque sensors offer long term reliability due to non moving parts and state of the art bonded foil strain gages. The anodized aluminum TRS Series is also available as a two axis sensor, torque and thrust, on special request. Whenever possible, the best approach for precision torque measurements is via reaction torque sensing, eliminating high maintenance and high cost of slip rings, bearings, and brushes.
-
Series 668B/D -
Dwyer Instruments Inc.
Our low cost SERIES 668B/D Compact Differential Pressure Transmitters are capable of sensing differential gage pressure with ±0.8% FS accuracy, and converts this pressure difference to a proportional high level analog output for both unidirectional and bi-directional pressure ranges. These transmitters can withstand up to 15 psig overpressure with no damage to the unit. The compact, lightweight design makes installation simple and easy. Units are protected against incorrect wiring, and include a protective terminal cover.
-
Aero Nav Laboratories, Inc.
This test measures the structural stresses induced in equipment when subjected to various environmental and operational loads. Strain gages, which are resistive devices whose outputs are proportional to the amount that they are deformed under strain, are placed at selected locations to yield stress levels which may then be compared to design allowable limits.
-
STS SERIES -
Transducer Techniques, Inc
The STS Series is our general purpose reaction type shaft torque sensor. They are often installed between devices such as motors, switches, shafts or axles, and their mounting plate to provide bi-directional torque output. They are available in six capacity ranges from 600 in-lb through 12,000 in-lb, and are made from 17-4ph heat treated stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
RTS SERIES -
Transducer Techniques, Inc
The RTS Series torque sensors were designed to fill the need for accurate torque measurements below 62.5 in.lbs. without giving up stiffness or sensitivity to forces from other directions. They are manufactured from sensor quality aluminum and anodized for long term durability. Bonded foil strain gages and materials of the highest quality are installed assuring high reliability. The four bolt hole pattern with the use of our O.D. or I.D. pilots on either end allows simple adaptation to any application.
-
SWS SERIES -
Transducer Techniques, Inc
Our SWS Series reaction type socket wrench torque sensors are available in ranges from 10 ft-lbs. through 1000 ft-lbs. and provide accurate measurements of bolt or nut wrenching torques. These sensors are bi-directional so both tightening and break-away torques can be measured. These low cost sensors deliver high accuracy and outstanding frequency response. alibration of mechanical torque wrenches may be performed with this sensor. The sensing element incorporates bonded foil strain gages of the highest quality.
-
33600 -
S & G Tool Aid Corp
Use to test for clogged or obstructed catalytic converters and mufflers. Fast and easy to use - threads into Oxygen Sensor Port. Includes 12mm and 18mm adapters to fit most domestic and imported vehicles. Gage measures 2 1/2" diameter and has dual scale: 15 PSI and 1.00 Kg/Cm2. Hose is 41" long.
-
34500 -
S & G Tool Aid Corp
Check oil pressure in automotive transmissions and engines. Adapters provide coverage of most domestic and imported cars and light trucks. Gage calibrated from 0-600 PSI (0-4,000 kPa & 0-7.0 BAR). Includes 6 feet of oil proof hose and 10 assorted fittings. Supplied with instructions in a durable vinyl pouch.
-
GaGe
GaGe provides several eXpert FPGA processing firmware options for use with CompuScope Digitizers. All standard default CompuScope Digitizer model configurations can store raw acquired waveform data to onboard sample memory and then transfer them quickly to the user for analysis, display and/or storage. The addition of optional eXpert FPGA processing firmware features allow for some signal processing analysis, or other specific functionality, to be performed on the digitizer hardware itself within its onboard Field Programmable Gate Array (FPGA).
