Showing results: 226 - 240 of 250 items found.
-
LPU SERIES -
Transducer Techniques, Inc
Our LPU Series are low profile, universal tension or compression "pancake" type load cells. They are available in 14 ranges from 100 lb through 50,000 lb Hold down bolt holes are provided through the outer diameter and a threaded hole provided through the center for pushing or pulling from either end. The ALB load buttons located in our accessories section, are ideal for compression applications. The LPU Series are made from 17-4ph heat treated stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
33900 -
S & G Tool Aid Corp
Test gasoline fuel pump pressure on most domestic and imported fuel injection equipped vehicles.Kit contains adapters to test all GM vehicles with Multi-port and some Throttle Body Injection (TBI). Test all Chrysler cars with Multi-port turbos and some TBI.Use on older Ford TBI systems not equipped with small Schrader test valve.Includes Large Gage with hang-up hook calibrated from 1-100 PSI (0-7.0 BAR).
-
PCE Instruments
PCE Instruments' accurate, affordable coating thickness gauge, thickness meter, surface testing and film gauge devices are used for material testing, manufacturing quality control and automotive paint inspection applications. Choose from a variety of coating thickness gauge, mil gage or paint meter products used for the non-destructive measurement of nonmagnetic coating, insulating layer and dry film thickness (DFT) on ferrous and / or non-ferrous metal substrates such as steel and aluminum.
-
PCE Instruments
PCE Instruments' accurate, affordable coating thickness gauge, thickness meter, surface testing and film gauge devices are used for material testing, manufacturing quality control and automotive paint inspection applications. Choose from a variety of coating thickness gauge, mil gage or paint meter products used for the non-destructive measurement of nonmagnetic coating, insulating layer and dry film thickness (DFT) on ferrous and / or non-ferrous metal substrates such as steel and aluminum.
-
VPG Transducers
The heart of each weighing system is a load cell. Load cells are mechanical components which act as force sensors by employing strain gages to provide an electrical output proportional to the applied force. Typically the electrical output is either analog (voltage or current) or digital. Load cells have specific mechanical packaging and sensing orientation to fit into electronic scales, and testing and monitoring systems. Load cells can be used for tension, compression, and/or shear measurement.
-
90332 -
HITEC Sensor Solutions Inc.
The 90332 digital FM telemetry systems is designed to be used with full-bridge, strain gage sensors. The system features a miniature transmitter powered by a simple 9V battery, and a remote receiver capability of receiving the digital transmission over long distances. The digital technique eliminates many of the problems associated with traditional analog frequency modulated telemetry systems. Improvements with a digital technique include elimination of ripple, temperature drift characteristics, and higher signal resolution.
-
PCE Instruments
Choose from a variety of thickness meter, mil gage or paint meter products used for the non-destructive measurement of nonmagnetic coating, insulating layer and dry film thickness (DFT) on ferrous and / or non-ferrous metal substrates such as steel and aluminum. Explore PCE Instruments' selection of accurate, affordable thickness meter, coating thickness gauge, surface testing and film gauge devices used for automotive paint inspection, material testing and manufacturing quality control applications.
-
53900 -
S & G Tool Aid Corp
Quick couplers provide for fast and easy hook-up. Kit contains adapters to test all GM vehicles with Multi-port and some Throttle Body Injection (TBI). Tests all Chrysler cars with Multi-port turbos and some TBI. Use on Ford older TBI systems not equipped with small Schrader test valve. Includes Large Gage with hang-up hook calibrated from 1-100 PSI (0-7.0 BAR). Supplied with instructions in a vinyl pouch.
-
MLC SERIES -
Transducer Techniques, Inc
The MLC Series is our miniature high capacity compression only load cell/force sensor, featuring low profile compact size for a wide range of portable and dedicated applications up to 30,000 lb The load diameter is slightly convex for accurate load distribution. Low deflection through design results in ultra fast frequency response. The MLCs are designed to be mounted in a shallow machined flat pocket or smooth flat surface, either free or fastened via a bottom 6-32 tapped hole. These load cells are manufactured from heat treated 17-4 ph stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial Environments.
-
NI
The C Series Universal Analog Input Module helps you perform multi-purpose measurements. This module includes built-in support for accelerometer, powered sensor, full-bridge, and voltage measurements as well as quarter-bridge, half-bridge, 60 V, and current measurements using measurement-specific adapters. You also can choose options to measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors.The C Series Universal Analog Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
H337H-2 -
Howell Instruments, Inc.
• Verifies engine performance duringtroubleshooting and after modulereplacement • Permits on-wing Interturbine Temperature(ITT) trim adjustment • Verifies aircraft ITT, torque and speedaccuracies in the specific engine applications • Requires minimal time for set-up and testing • Measures and displays various engineparameters and calculates functions duringflight line and test cell engine runs including: - ITT Setting (Trim Resistor) - ITT and Gas Generator Speed Margins - Compressor Efficiency - Cockpit Gage Verification (ITT, Torque, GasGenerator Speed and Propeller Speed)
-
34000 -
S & G Tool Aid Corp
Test compression on all domestic and foreign cars and most trucks. Adapters fit vehicles with 14mm and 18mm plugs including long reach and 5/8" hex plugs. Flex hose eliminates need to remove auxiliary equipment such as power brakes and steering, air conditioning and manifold. Screw in adapters guarantee accuracy over push-in type testers. Quick side release valve permits retest without removal of adapters. Gage ranges 0-300 PSI and 0-21 BAR. Supplied in storage pouch.
-
779781-02 -
NI
100 S/s/channel, 4-Channel C Series Universal Analog Input Module - The NI‑9219 is designed for multipurpose testing. With the NI‑9219, you can measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors, as well as make quarter-bridge, half-bridge, and full-bridge current measurements, with built-in voltage and current excitation. Each channel is individually selectable, so you can perform a different measurement type on each channel.
-
785994-01 -
NI
100 S/s/channel, 4-Channel C Series Universal Analog Input Module - The NI‑9219 is designed for multipurpose testing. With the NI‑9219, you can measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors, as well as make quarter-bridge, half-bridge, and full-bridge current measurements, with built-in voltage and current excitation. Each channel is individually selectable, so you can perform a different measurement type on each channel.
-
General Purpose -
Encore Electronics, Inc.
Encore offers a complete line of General Purpose Signal Conditioning instrumentation to meet even the most demanding requirements. Packaged as interchangeable two-channel plug-in modules, Encore’s broad product line includes frequency to voltage converters, strain gage amplifiers, accelerometer conditioners, digital voltmeters and DC power supplies. All of our systems feature a common CAL input on the rear of the rack which allows for calibration of the entire rack. Calibration function varies based on the modules installed. For example, the Model 633 applies a shunt calibration resistor across the bridge, while the Model 149 applies a reference charge source to the input. Contact Encore today and let our team of design engineers help you determine which of our products is best for your application.
